参数资料
型号: JN5139/001,531
厂商: NXP Semiconductors
文件页数: 27/82页
文件大小: 0K
描述: MCU 802.15.4 32BIT 2.4G 56-QFN
标准包装: 500
系列: JN5139-001Rx
频率: 2.4GHz
调制或协议: 802.15.4 Zigbee
应用: 通用
功率 - 输出: 3dBm
灵敏度: -96dBm
电源电压: 2.7 V ~ 3.6 V
电流 - 接收: 37mA
电流 - 传输: 37mA
数据接口: PCB,表面贴装
存储容量: 96kB RAM,192kB ROM
天线连接器: PCB,表面贴装
工作温度: -40°C ~ 85°C
封装/外壳: 56-VFQFN
包装: 带卷 (TR)
for transmission. During the passage of the bitstream to the modem, it passes through a CRC checksum generator
that calculates the checksum on-the-fly, and appends it to the end of the frame.
If using slotted access, it is possible for a transmission to overrun the time in its allocated slot; the Baseband
Processor handles this situation autonomously and notifies the protocol software via interrupt, rather than requiring it
to handle the overrun explicitly.
8.3.2 Reception
During reception, the radio is set to receive on a particular channel. On receipt of data from the modem, the frame is
directed into the Tx/Rx Frame Buffer where both header and frame data can be read by the protocol software. An
interrupt may be provided on receipt of the frame header. As the frame data is being received from the modem it is
passed through a checksum generator; at the end of the reception the checksum result is compared with the
checksum at the end of the message to ensure that the data has been received correctly. An interrupt may be
provided to indicate successful packet reception.
During reception, the modem determines the Link Quality, which is made available at the end of the reception as part
of the requirements of IEEE802.15.4.
8.3.3 Auto Acknowledge
Part of the protocol allows for transmitted frames to be acknowledged by the destination sending an acknowledge
packet within a very short window after the transmitted frame has been received. The JN5139 baseband processor
can automatically construct and send the acknowledgement packet without processor intervention and hence avoid
the protocol software being involved in time-critical processing within the acknowledge sequence. The JN5139
baseband processor can also request an acknowledge for packets being transmitted and handle the reception of
acknowledged packets without processor intervention.
8.3.4 Beacon Generation
In beaconing networks, the baseband processor can automatically generate and send beacon frames; the repetition
rate of the beacons is programmed by the CPU, and the baseband then constructs the beacon contents from data
delivered by the CPU. The baseband processor schedules the beacons and transmits them without CPU
intervention.
8.3.5 Security
The baseband processor supports the transmission and reception of secured frames using the Advanced Encryption
Standard (AES) algorithm transparently to the CPU. This is done by passing incoming and outgoing data through an
in-line security engine that is able to perform encryption and decryption operations on-the-fly, resulting in minimal
processor intervention. The CPU must provide the appropriate encrypt/decrypt keys for the transmission or
reception. On transmission, the key can be programmed at the same time as the rest of the frame data and setup
information.
During reception, the CPU must look up the key and provide it from information held in the header of the incoming
frame. However, the hardware of the security engine can process data much faster than the incoming frame data
rate. This means that it is possible to allow the CPU to receive the interrupt from the header of an incoming packet,
read where the frame originated, look up the key and program it to the security hardware before the end of the frame
has arrived. By providing a small amount of buffering to store incoming data while the lookup process is taking place,
the security engine can catch up processing the frame so that when the frame arrives in the receive frame buffer it is
fully decrypted.
8.4 Security Coprocessor
As well as being used during in-line encryption/decryption operations over a streaming interface and in external
memory encryption, it is also possible to use the AES core as a coprocessor to the CPU of the JN5139. To allow the
hardware to be shared between the two interfaces an arbiter ensures that the streaming interface to the AES core
always has priority, to ensure that in-line processing can take place at any time.
Some protocols require that security operations can be performed on buffered data rather than in-line. A hardware
implementation of the encryption engine significantly speeds up the processing of the contents of these buffers. The
Security Coprocessor can be accessed through software to allow the contents of memory buffers to be transformed.
? NXP Laboratories UK 2010
JN-DS-JN5139 1v9
27
相关PDF资料
PDF描述
JN5139-EK000 KIT EVAL IEEE802.15.4 JN5139
JN5139/Z01,515 IC MCU ZIGBEE 32BIT 2.4G 56QFN
JN5139-Z01-M/02R1V MODULE ZIGBEE SMA CONN HP JN5139
JN5148/001M04T,534 MODULE ZIGBEE PRO HP U.FL CONN
JN5148-UG010 KIT UPGRADE ZIGBEE PRO
相关代理商/技术参数
参数描述
JN5139-001-M/00R1T 功能描述:Zigbee/802.15.4模块 WIRELESS MCU IEEE802.15.4 TRNSCVR RoHS:否 制造商:Digi International 频带:902 MHz to 928 MHz 视线范围: 数据速率: 灵敏度: 工作电源电压:2.4 V to 3.6 V 传输供电电流:215 mA 接收供电电流:26 mA 输出功率:250 mW 天线连接器类型:Wire 最大工作温度:+ 85 C 尺寸:32.94 mm x 22 mm x 2.03 mm
JN5139-001-M/01R1V 功能描述:Zigbee/802.15.4模块 WIRELESS MCU IEEE802.15.4 TRNSCVR RoHS:否 制造商:Digi International 频带:902 MHz to 928 MHz 视线范围: 数据速率: 灵敏度: 工作电源电压:2.4 V to 3.6 V 传输供电电流:215 mA 接收供电电流:26 mA 输出功率:250 mW 天线连接器类型:Wire 最大工作温度:+ 85 C 尺寸:32.94 mm x 22 mm x 2.03 mm
JN5139-001-M/02R1V 功能描述:Zigbee/802.15.4模块 WIRELESS MCU IEEE802.15.4 TRNSCVR RoHS:否 制造商:Digi International 频带:902 MHz to 928 MHz 视线范围: 数据速率: 灵敏度: 工作电源电压:2.4 V to 3.6 V 传输供电电流:215 mA 接收供电电流:26 mA 输出功率:250 mW 天线连接器类型:Wire 最大工作温度:+ 85 C 尺寸:32.94 mm x 22 mm x 2.03 mm
JN5139-001-M/03R1T 功能描述:Zigbee/802.15.4模块 WIRELESS MCU IEEE802.15.4 TRNSCVR RoHS:否 制造商:Digi International 频带:902 MHz to 928 MHz 视线范围: 数据速率: 灵敏度: 工作电源电压:2.4 V to 3.6 V 传输供电电流:215 mA 接收供电电流:26 mA 输出功率:250 mW 天线连接器类型:Wire 最大工作温度:+ 85 C 尺寸:32.94 mm x 22 mm x 2.03 mm
JN5139-001-M/04R1T 功能描述:Zigbee/802.15.4模块 WIRELESS MCU IEEE802.15.4 TRNSCVR RoHS:否 制造商:Digi International 频带:902 MHz to 928 MHz 视线范围: 数据速率: 灵敏度: 工作电源电压:2.4 V to 3.6 V 传输供电电流:215 mA 接收供电电流:26 mA 输出功率:250 mW 天线连接器类型:Wire 最大工作温度:+ 85 C 尺寸:32.94 mm x 22 mm x 2.03 mm