参数资料
型号: JN5139/001,531
厂商: NXP Semiconductors
文件页数: 44/82页
文件大小: 0K
描述: MCU 802.15.4 32BIT 2.4G 56-QFN
标准包装: 500
系列: JN5139-001Rx
频率: 2.4GHz
调制或协议: 802.15.4 Zigbee
应用: 通用
功率 - 输出: 3dBm
灵敏度: -96dBm
电源电压: 2.7 V ~ 3.6 V
电流 - 接收: 37mA
电流 - 传输: 37mA
数据接口: PCB,表面贴装
存储容量: 96kB RAM,192kB ROM
天线连接器: PCB,表面贴装
工作温度: -40°C ~ 85°C
封装/外壳: 56-VFQFN
包装: 带卷 (TR)

14 Two-Wire Serial interface
The JN5139 includes an industry standard two-wire synchronous serial interface (SIF) that provides a simple and
efficient method of data exchange between devices. The system operates as a master only and uses a serial data
line (SIF_D) and a serial clock line (SIF_CLK) to perform bi-directional data transfers; includes the following features:
?
?
?
?
?
?
?
Compatible with both I 2 C and SMbus peripherals (master only mode)
Software programmable clock frequency
Clock stretching and wait state generation
Software programmable acknowledge bit
Interrupt or bit-polling driven byte-by-byte data-transfers
Bus busy detection
Support for 7 and 10 bit addressing modes
Prescale
Register
Command
Register
Byte
Command
Clock
Generator
Bit
Command
SIF_CLK
Controller
Controller
SIF_D
Status
Register
Transmit
Register
Data I/O
Shift
Register
Receive
Register
Figure 35: SIF Block Diagram
The software libraries allow full control of the underlying registers and give access to the following features.
A configurable prescale register allows the interface to be configured to operate at up to 400kbit/s. The clock
generator handles the clock stretching required by some slave devices.
The Byte Command Controller handles traffic at the byte level. It takes data from the Command Register and
translates it into sequences based on the transmission of a single byte. By setting the start, stop, read, write and
acknowledge control bits in the command register it is possible to generate read or write sequences on the bus.
The data I/O shift register contains the data associated with the current transfer. During a read operation, data is
shifted into this register from the SIF_D line. When the read is complete the byte is copied into the receive register
and can be accessed.
During a write operation the contents of the transmit register are copied into the shift register and then onto the SIF_D
line. It is possible to generate an interrupt upon the completion of a byte transmission or reception. If interrupt-driven
communication is not desired it is possible to poll the status of the interface.
44
JN-DS-JN5139 1v9
? NXP Laboratories UK 2010
相关PDF资料
PDF描述
JN5139-EK000 KIT EVAL IEEE802.15.4 JN5139
JN5139/Z01,515 IC MCU ZIGBEE 32BIT 2.4G 56QFN
JN5139-Z01-M/02R1V MODULE ZIGBEE SMA CONN HP JN5139
JN5148/001M04T,534 MODULE ZIGBEE PRO HP U.FL CONN
JN5148-UG010 KIT UPGRADE ZIGBEE PRO
相关代理商/技术参数
参数描述
JN5139-001-M/00R1T 功能描述:Zigbee/802.15.4模块 WIRELESS MCU IEEE802.15.4 TRNSCVR RoHS:否 制造商:Digi International 频带:902 MHz to 928 MHz 视线范围: 数据速率: 灵敏度: 工作电源电压:2.4 V to 3.6 V 传输供电电流:215 mA 接收供电电流:26 mA 输出功率:250 mW 天线连接器类型:Wire 最大工作温度:+ 85 C 尺寸:32.94 mm x 22 mm x 2.03 mm
JN5139-001-M/01R1V 功能描述:Zigbee/802.15.4模块 WIRELESS MCU IEEE802.15.4 TRNSCVR RoHS:否 制造商:Digi International 频带:902 MHz to 928 MHz 视线范围: 数据速率: 灵敏度: 工作电源电压:2.4 V to 3.6 V 传输供电电流:215 mA 接收供电电流:26 mA 输出功率:250 mW 天线连接器类型:Wire 最大工作温度:+ 85 C 尺寸:32.94 mm x 22 mm x 2.03 mm
JN5139-001-M/02R1V 功能描述:Zigbee/802.15.4模块 WIRELESS MCU IEEE802.15.4 TRNSCVR RoHS:否 制造商:Digi International 频带:902 MHz to 928 MHz 视线范围: 数据速率: 灵敏度: 工作电源电压:2.4 V to 3.6 V 传输供电电流:215 mA 接收供电电流:26 mA 输出功率:250 mW 天线连接器类型:Wire 最大工作温度:+ 85 C 尺寸:32.94 mm x 22 mm x 2.03 mm
JN5139-001-M/03R1T 功能描述:Zigbee/802.15.4模块 WIRELESS MCU IEEE802.15.4 TRNSCVR RoHS:否 制造商:Digi International 频带:902 MHz to 928 MHz 视线范围: 数据速率: 灵敏度: 工作电源电压:2.4 V to 3.6 V 传输供电电流:215 mA 接收供电电流:26 mA 输出功率:250 mW 天线连接器类型:Wire 最大工作温度:+ 85 C 尺寸:32.94 mm x 22 mm x 2.03 mm
JN5139-001-M/04R1T 功能描述:Zigbee/802.15.4模块 WIRELESS MCU IEEE802.15.4 TRNSCVR RoHS:否 制造商:Digi International 频带:902 MHz to 928 MHz 视线范围: 数据速率: 灵敏度: 工作电源电压:2.4 V to 3.6 V 传输供电电流:215 mA 接收供电电流:26 mA 输出功率:250 mW 天线连接器类型:Wire 最大工作温度:+ 85 C 尺寸:32.94 mm x 22 mm x 2.03 mm