- 您现在的位置：买卖IC网 > Datasheet目录466 > JN5139/001,531 (NXP Semiconductors)MCU 802.15.4 32BIT 2.4G 56-QFN Datasheet资料下载
参数资料
| 型号： | JN5139/001,531 |
| 厂商： | NXP Semiconductors |
| 文件页数： | 41/82页 |
| 文件大小： | 0K |
| 描述： | MCU 802.15.4 32BIT 2.4G 56-QFN |
| 标准包装： | 500 |
| 系列： | JN5139-001Rx |
| 频率： | 2.4GHz |
| 调制或协议： | 802.15.4 Zigbee |
| 应用： | 通用 |
| 功率 - 输出： | 3dBm |
| 灵敏度： | -96dBm |
| 电源电压： | 2.7 V ~ 3.6 V |
| 电流 - 接收： | 37mA |
| 电流 - 传输： | 37mA |
| 数据接口： | PCB，表面贴装 |
| 存储容量： | 96kB RAM，192kB ROM |
| 天线连接器： | PCB，表面贴装 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 56-VFQFN |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页当前第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页
if the device is asleep then the interrupt may be used as an event to end the sleep period. See Section 16 for further
details on how they are used during sleep periods. Features include:
?
?
?
32-bit down-counter
Optionally runs during sleep periods
Clocked from either:
?
?
32kHz RC Oscillator
32kHz External Clock
A wakeup timer consists of a 32-bit down counter clocked from the 32 kHz system clock. An interrupt or wakeup
event can be generated when the counter reaches zero. On reaching zero the counter will continue to count down
until stopped, which allows the latency in responding to the interrupt to be measured. If an interrupt or wakeup event
is required, the timer interrupt should be enabled before loading the count value for the period. Once the count value
is loaded and counter started, the counter begins to count down; the counter can be stopped at any time through
software control. The counter will remain at the value it contained when the timer was stopped and no interrupt will
be generated. The status of the timers can be read to indicate if the timers are running and/or have expired; this is
useful when the timer interrupts are masked. This operation will reset any expired status flags.
12.3.1 RC Oscillator Calibration
The RC oscillator that can be used to time sleep periods is designed to require very little power to operate and be
self-contained, requiring no external timing components and hence is lower cost. As a consequence of using on-chip
resistors and capacitors, the inherent absolute accuracy and temperature coefficient is lower than that of a crystal
oscillator, but once calibrated the accuracy approaches that of a crystal oscillator. Sleep time periods should be as
close to the desired time as possible in order to allow the device to wake up in time for important events, for example
beacon transmissions in the IEEE802.15.4 protocol. If the sleep time is accurate, the device can be programmed to
wake up very close to the calculated time of the event and so keep current consumption to a minimum. If the sleep
time is less accurate, it will be necessary to wake up earlier in order to be certain the event will be captured. If the
device wakes earlier, it will be awake for longer and so reduce battery life.
In order to allow sleep time periods to be as close to the desired length as possible, the true frequency of the RC
oscillator needs to be determined to better than the initial 30% accuracy. The calibration factor can then be used to
calculate the true number of nominal 32kHz periods needed to make up a particular sleep time. A calibration
reference timer, clocked from the crystal oscillator, is provided to allow comparisons to be made between the RC
clock and the 16MHz crystal oscillator when the JN5139 is awake. Operation is as follows:
?
?
?
?
Wakeup timer0 is disabled and programmed with a number of 32kHz ticks
Timer0 event status must be cleared
Calibration mode is enabled which causes the Calibration Reference counter to be zeroed. Both counters
start counting, the wakeup timer decrementing and the calibration counter incrementing
When the wakeup timer reaches zero the Reference Counter is stopped, allowing software to read the
number of 16MHz clock ticks generated during the time represented by the number of 32kHz ticks
programmed in the wakeup timer. The true period of the 32kHz clock can thus be determined and used
when programming a wakeup timer to achieve a better accuracy and hence more accurate sleep periods
For a RC oscillator running at exactly 32kHz the value returned by the calibration procedure should be 10000, for a
calibration period of twenty 32kHz clock periods. If the oscillator is running faster than 32kHz the count will be less
than 10000, if running slower the value will be higher. For a calibration count of 9000, indicating that the RC oscillator
period is running at approximately 35kHz, to time for a period of 2 seconds the timer should be loaded with 71,111
((10000/9000) x (32000 x 2)) rather than 64000.
? NXP Laboratories UK 2010
JN-DS-JN5139 1v9
41
相关PDF资料 |
PDF描述 |
|---|---|
| JN5139-EK000 | KIT EVAL IEEE802.15.4 JN5139 |
| JN5139/Z01,515 | IC MCU ZIGBEE 32BIT 2.4G 56QFN |
| JN5139-Z01-M/02R1V | MODULE ZIGBEE SMA CONN HP JN5139 |
| JN5148/001M04T,534 | MODULE ZIGBEE PRO HP U.FL CONN |
| JN5148-UG010 | KIT UPGRADE ZIGBEE PRO |
相关代理商/技术参数 |
参数描述 |
|---|---|
| JN5139-001-M/00R1T | 功能描述:Zigbee/802.15.4模块 WIRELESS MCU IEEE802.15.4 TRNSCVR RoHS:否 制造商:Digi International 频带:902 MHz to 928 MHz 视线范围: 数据速率: 灵敏度: 工作电源电压:2.4 V to 3.6 V 传输供电电流:215 mA 接收供电电流:26 mA 输出功率:250 mW 天线连接器类型:Wire 最大工作温度:+ 85 C 尺寸:32.94 mm x 22 mm x 2.03 mm |
| JN5139-001-M/01R1V | 功能描述:Zigbee/802.15.4模块 WIRELESS MCU IEEE802.15.4 TRNSCVR RoHS:否 制造商:Digi International 频带:902 MHz to 928 MHz 视线范围: 数据速率: 灵敏度: 工作电源电压:2.4 V to 3.6 V 传输供电电流:215 mA 接收供电电流:26 mA 输出功率:250 mW 天线连接器类型:Wire 最大工作温度:+ 85 C 尺寸:32.94 mm x 22 mm x 2.03 mm |
| JN5139-001-M/02R1V | 功能描述:Zigbee/802.15.4模块 WIRELESS MCU IEEE802.15.4 TRNSCVR RoHS:否 制造商:Digi International 频带:902 MHz to 928 MHz 视线范围: 数据速率: 灵敏度: 工作电源电压:2.4 V to 3.6 V 传输供电电流:215 mA 接收供电电流:26 mA 输出功率:250 mW 天线连接器类型:Wire 最大工作温度:+ 85 C 尺寸:32.94 mm x 22 mm x 2.03 mm |
| JN5139-001-M/03R1T | 功能描述:Zigbee/802.15.4模块 WIRELESS MCU IEEE802.15.4 TRNSCVR RoHS:否 制造商:Digi International 频带:902 MHz to 928 MHz 视线范围: 数据速率: 灵敏度: 工作电源电压:2.4 V to 3.6 V 传输供电电流:215 mA 接收供电电流:26 mA 输出功率:250 mW 天线连接器类型:Wire 最大工作温度:+ 85 C 尺寸:32.94 mm x 22 mm x 2.03 mm |
| JN5139-001-M/04R1T | 功能描述:Zigbee/802.15.4模块 WIRELESS MCU IEEE802.15.4 TRNSCVR RoHS:否 制造商:Digi International 频带:902 MHz to 928 MHz 视线范围: 数据速率: 灵敏度: 工作电源电压:2.4 V to 3.6 V 传输供电电流:215 mA 接收供电电流:26 mA 输出功率:250 mW 天线连接器类型:Wire 最大工作温度:+ 85 C 尺寸:32.94 mm x 22 mm x 2.03 mm |
发布紧急采购，3分钟左右您将得到回复。