- 您现在的位置：买卖IC网 > PDF目录11585 > KSZ8841-16MQL (Micrel Inc)IC MAC CTRLR 8/16BIT 128-PQFP PDF资料下载
参数资料
| 型号： | KSZ8841-16MQL |
| 厂商： | Micrel Inc |
| 文件页数： | 27/105页 |
| 文件大小： | 0K |
| 描述： | IC MAC CTRLR 8/16BIT 128-PQFP |
| 标准包装： | 66 |
| 控制器类型： | 以太网控制器，MAC |
| 接口： | 总线 |
| 电源电压： | 3.1 V ~ 3.5 V |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 128-BFQFP |
| 供应商设备封装： | 128-PQFP（14x20） |
| 包装： | 托盘 |
| 产品目录页面： | 1080 (CN2011-ZH PDF) |
| 配用： | 576-1631-ND - BOARD EVALUATION KSZ8841-16MQL |
| 其它名称： | 576-2112 KSZ8841-16MQL-ND |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页当前第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页
Micrel, Inc.
KSZ8841-16/32 MQL/MVL/MBL
October 2007
28
M9999-102207-1.6
Magic Packet is a standard feature integrated into the KSZ8841M. The controller implements multiple advanced power-
down modes including Magic Packet to conserve power and operate more efficiently.
Once the KSZ8841M has been put into Magic Packet Enable mode (WFCR[7]=1), it scans all incoming frames addressed
to the node for a specific data sequence, which indicates to the controller this is a Magic Packet (MP) frame.
A Magic Packet frame must also meet the basic requirements for the LAN technology chosen, such as Source Address
(SA), Destination Address (DA), which may be the receiving station’s IEEE address or a multicast or broadcast address
and CRC.
The specific sequence consists of 16 duplications of the IEEE address of this node, with no breaks or interruptions. This
sequence can be located anywhere within the packet, but must be preceded by a synchronization stream. The
synchronization stream allows the scanning state machine to be much simpler. The synchronization stream is defined as
6 bytes of FFh. The device will also accept a broadcast frame, as long as the 16 duplications of the IEEE address match
the address of the machine to be awakened.
example
If the IEEE address for a particular node on a network is 11h 22h, 33h, 44h, 55h, 66h, the LAN controller would be
scanning for the data sequence (assuming an Ethernet frame):
DESTINATION SOURCE – MISC - FF FF FF FF FF FF - 11 22 33 44 55 66 - 11 22 33 44 55 66 - 11 22 33 44 55 66 -
11 22 33 44 55 66 - 11 22 33 44 55 66 - 11 22 33 44 55 66 - 11 22 33 44 55 66 - 11 22 33 44 55 66 - 11 22 33 44 55 66 -
11 22 33 44 55 66 - MISC - CRC.
There are no further restrictions on a Magic Packet frame. For instance, the sequence could be in a TCP/IP packet or an
IPX packet. The frame may be bridged or routed across the network without affecting its ability to wake-up a node at the
frame’s destination.
If the LAN controller scans a frame and does not find the specific sequence shown above, it discards the frame and takes
no further action. If the KSZ8841M controller detects the data sequence, however, it then alerts the PC’s power
management circuitry (assert the PMEN pin) to wake up the system.
Physical Layer Transceiver (PHY)
100BASE-TX Transmit
The 100BASE-TX transmit function performs parallel-to-serial conversion, 4B/5B coding, scrambling, NRZ-to-NRZI
conversion, and MLT3 encoding and transmission.
The circuitry starts with a parallel-to-serial conversion, which converts the MII data from the MAC into a 125MHz serial bit
stream. The data and control stream is then converted into 4B/5B coding, followed by a scrambler. The serialized data is
further converted from NRZ-to-NRZI format, and then transmitted in MLT3 current output. An external 1% 3.01K
resistor
for the 1:1 transformer ratio sets the output current.
The output signal has a typical rise/fall time of 4ns and complies with the ANSI TP-PMD standard regarding amplitude
balance, overshoot, and timing jitter. The wave-shaped 10BASE-T output driver is also incorporated into the 100BASE-TX
driver.
相关PDF资料 |
PDF描述 |
|---|---|
| PIC12CE518-04E/SM | IC MCU OTP 512X12 W/EE 8-SOIC |
| KSZ8895RQ | IC 10/100-T 5 PORT SW 128PQFP |
| PIC16LC620A-04/P | IC MCU OTP 512X14 COMP 18DIP |
| KSZ8863FLLI | IC ETHERNET SWITCH 3PORT 48-LQFP |
| PIC16C505-04E/SL | IC MCU OTP 1KX12 14SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| KSZ8841-16MQL A6 | 功能描述:IC MAC CTRLR 8/16BIT 128-PQFP RoHS:是 类别:集成电路 (IC) >> 接口 - 控制器 系列:- 标准包装:4,900 系列:- 控制器类型:USB 2.0 控制器 接口:串行 电源电压:3 V ~ 3.6 V 电流 - 电源:135mA 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:36-VFQFN 裸露焊盘 供应商设备封装:36-QFN（6x6） 包装:* 其它名称:Q6396337A |
| KSZ8841-16MQL-EVAL | 功能描述:以太网开发工具 KSZ8841-16MQL Evaluation Board RoHS:否 制造商:Micrel 产品:Evaluation Boards 类型:Ethernet Transceivers 工具用于评估:KSZ8873RLL 接口类型:RMII 工作电源电压: |
| KSZ8841-16MVL | 功能描述:以太网 IC Single Ethernet Port + Generic (8, 16-bit) bus interface(Lead Free) RoHS:否 制造商:Micrel 产品:Ethernet Switches 收发器数量:2 数据速率:10 Mb/s, 100 Mb/s 电源电压-最大:1.25 V, 3.45 V 电源电压-最小:1.15 V, 3.15 V 最大工作温度:+ 85 C 封装 / 箱体:QFN-64 封装:Tray |
| KSZ8841-16MVL TR | 功能描述:以太网 IC Single Ethernet Port + Generic (8, 16-bit) bus interface(Lead Free) RoHS:否 制造商:Micrel 产品:Ethernet Switches 收发器数量:2 数据速率:10 Mb/s, 100 Mb/s 电源电压-最大:1.25 V, 3.45 V 电源电压-最小:1.15 V, 3.15 V 最大工作温度:+ 85 C 封装 / 箱体:QFN-64 封装:Tray |
| KSZ8841-16MVL-EVAL | 功能描述:BOARD EVALUATION KSZ8841-16MVL RoHS:是 类别:编程器，开发系统 >> 过时/停产零件编号 系列:- 标准包装:1 系列:- 类型:MCU 适用于相关产品:Freescale MC68HC908LJ/LK（80-QFP ZIF 插口） 所含物品:面板、缆线、软件、数据表和用户手册 其它名称:520-1035 |
发布紧急采购，3分钟左右您将得到回复。