- 您现在的位置：买卖IC网 > PDF目录11585 > KSZ8841-16MQL (Micrel Inc)IC MAC CTRLR 8/16BIT 128-PQFP PDF资料下载
参数资料
| 型号： | KSZ8841-16MQL |
| 厂商： | Micrel Inc |
| 文件页数： | 32/105页 |
| 文件大小： | 0K |
| 描述： | IC MAC CTRLR 8/16BIT 128-PQFP |
| 标准包装： | 66 |
| 控制器类型： | 以太网控制器，MAC |
| 接口： | 总线 |
| 电源电压： | 3.1 V ~ 3.5 V |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 128-BFQFP |
| 供应商设备封装： | 128-PQFP（14x20） |
| 包装： | 托盘 |
| 产品目录页面： | 1080 (CN2011-ZH PDF) |
| 配用： | 576-1631-ND - BOARD EVALUATION KSZ8841-16MQL |
| 其它名称： | 576-2112 KSZ8841-16MQL-ND |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页当前第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页
Micrel, Inc.
KSZ8841-16/32 MQL/MVL/MBL
October 2007
32
M9999-102207-1.6
LinkMD Cable Diagnostics
The KSZ8841M LinkMD uses time domain reflectometry (TDR) to analyze the cabling plant for common cabling problems
such as open circuits, short circuits, and impedance mismatches.
LinkMD works by sending a pulse of known amplitude and duration down the MDI and MDI-X pairs and then analyzes the
shape of the reflected signal. Timing the pulse duration gives an indication of the distance to the cabling fault with a
maximum distance of 200m and an accuracy of +/–2m. Internal circuitry displays the TDR information in a user-readable
digital format in register P1VCT[8:0].
Note: cable diagnostics are only valid for copper connections – fiber-optic operation is not supported.
Access
LinkMD is initiated by accessing register P1VCT, the LinkMD Control/Status register, in conjunction with register P1CR4,
the 100BASE-TX PHY Controller register.
Usage
LinkMD can be run at any time by ensuring that Auto-MDIX has been disabled. To disable Auto-MDIX, write a ‘1’ to
P1CR4[10] to enable manual control over the pair used to transmit the LinkMD pulse. The self-clearing cable diagnostic
test enable bit, P1VCT[15], is set to ‘1’ to start the test on this pair.
When bit P1VCT[15] returns to ‘0’, the test is complete. The test result is returned in bits P1VCT[14:13] and the distance
is returned in bits P1VCT[8:0]. The cable diagnostic test results are as follows:
00 = Valid test, normal condition
01 = Valid test, open circuit in cable
10 = Valid test, short circuit in cable
11 = Invalid test, LinkMD failed
If P1VCT[14:13]=11, this indicates an invalid test, and occurs when the KSZ8841M is unable to shut down the link
partner. In this instance, the test is not run, as it is not possible for the KSZ8841M to determine if the detected signal is a
reflection of the signal generated or a signal from another source.
Cable distance can be approximated by the following formula:
P1VCT[8:0] x 0.4m for port 1 cable distance
This constant may be calibrated for different cabling conditions, including cables with a velocity of propagation that varies
significantly from the norm.
Media Access Control (MAC) Operation
The KSZ8841M strictly abides by IEEE 802.3 standards to maximize compatibility.
Inter Packet Gap (IPG)
If a frame is successfully transmitted, then the minimum 96-bit time for IPG is measured between two consecutive
packets. If the current packet is experiencing collisions, the minimum 96-bit time for IPG is measured from carrier sense
(CRS) to the next transmit packet.
Back-Off Algorithm
The KSZ8841M implements the IEEE standard 802.3 binary exponential back-off algorithm in half-duplex mode. After 16
collisions, the packet is dropped.
Late Collision
If a transmit packet experiences collisions after 512 bit times of the transmission, the packet is dropped.
Flow Control
The KSZ8841M supports standard 802.3x flow control frames on both transmit and receive sides.
On the receive side, if the KSZ8841M receives a pause control frame, the KSZ8841M will not transmit the next normal
frame until the timer, specified in the pause control frame, expires. If another pause frame is received before the current
timer expires, the timer will be updated with the new value in the second pause frame. During this period (while it is flow
controlled), only flow control packets from the KSZ8841M are transmitted.
On the transmit side, the KSZ8841M has intelligent and efficient ways to determine when to invoke flow control. The flow
相关PDF资料 |
PDF描述 |
|---|---|
| PIC12CE518-04E/SM | IC MCU OTP 512X12 W/EE 8-SOIC |
| KSZ8895RQ | IC 10/100-T 5 PORT SW 128PQFP |
| PIC16LC620A-04/P | IC MCU OTP 512X14 COMP 18DIP |
| KSZ8863FLLI | IC ETHERNET SWITCH 3PORT 48-LQFP |
| PIC16C505-04E/SL | IC MCU OTP 1KX12 14SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| KSZ8841-16MQL A6 | 功能描述:IC MAC CTRLR 8/16BIT 128-PQFP RoHS:是 类别:集成电路 (IC) >> 接口 - 控制器 系列:- 标准包装:4,900 系列:- 控制器类型:USB 2.0 控制器 接口:串行 电源电压:3 V ~ 3.6 V 电流 - 电源:135mA 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:36-VFQFN 裸露焊盘 供应商设备封装:36-QFN（6x6） 包装:* 其它名称:Q6396337A |
| KSZ8841-16MQL-EVAL | 功能描述:以太网开发工具 KSZ8841-16MQL Evaluation Board RoHS:否 制造商:Micrel 产品:Evaluation Boards 类型:Ethernet Transceivers 工具用于评估:KSZ8873RLL 接口类型:RMII 工作电源电压: |
| KSZ8841-16MVL | 功能描述:以太网 IC Single Ethernet Port + Generic (8, 16-bit) bus interface(Lead Free) RoHS:否 制造商:Micrel 产品:Ethernet Switches 收发器数量:2 数据速率:10 Mb/s, 100 Mb/s 电源电压-最大:1.25 V, 3.45 V 电源电压-最小:1.15 V, 3.15 V 最大工作温度:+ 85 C 封装 / 箱体:QFN-64 封装:Tray |
| KSZ8841-16MVL TR | 功能描述:以太网 IC Single Ethernet Port + Generic (8, 16-bit) bus interface(Lead Free) RoHS:否 制造商:Micrel 产品:Ethernet Switches 收发器数量:2 数据速率:10 Mb/s, 100 Mb/s 电源电压-最大:1.25 V, 3.45 V 电源电压-最小:1.15 V, 3.15 V 最大工作温度:+ 85 C 封装 / 箱体:QFN-64 封装:Tray |
| KSZ8841-16MVL-EVAL | 功能描述:BOARD EVALUATION KSZ8841-16MVL RoHS:是 类别:编程器，开发系统 >> 过时/停产零件编号 系列:- 标准包装:1 系列:- 类型:MCU 适用于相关产品:Freescale MC68HC908LJ/LK（80-QFP ZIF 插口） 所含物品:面板、缆线、软件、数据表和用户手册 其它名称:520-1035 |
发布紧急采购，3分钟左右您将得到回复。