- 您现在的位置：买卖IC网 > PDF目录11595 > KSZ8851-16MQL (Micrel Inc)IC CTLR MAC/PHY NON-PCI 128-PQFP PDF资料下载
参数资料
| 型号： | KSZ8851-16MQL |
| 厂商： | Micrel Inc |
| 文件页数： | 15/88页 |
| 文件大小： | 0K |
| 描述： | IC CTLR MAC/PHY NON-PCI 128-PQFP |
| 产品培训模块： | KSZ8851 10/100 Embedded Controllers |
| 标准包装： | 66 |
| 控制器类型： | 以太网控制器，MAC/PHY |
| 接口： | 总线 |
| 电源电压： | 1.8V，2.5V，3.3V |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 128-BFQFP |
| 供应商设备封装： | 128-PQFP（14x20） |
| 包装： | 托盘 |
| 产品目录页面： | 1081 (CN2011-ZH PDF) |
| 配用： | 576-3292-ND - BOARD EVALUATION KSZ8851-16MLL |
| 其它名称： | 576-3253 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页当前第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页
Micrel, Inc.
KSZ8851-16/32 MQL/MQLI
August 2009
22
M9999-083109-2.0
Functional Description
The KSZ8851M is a single-chip Fast Ethernet MAC/PHY controller consisting of a 10/100 physical layer transceiver
(PHY), a MAC, and a Bus Interface Unit (BIU) that controls the KSZ8851M via an 8-bit, 16-bit or 32-bit host bus interface.
The KSZ8851M is fully compliant to IEEE802.3u standards.
Functional Overview
Power Management
The KSZ8851M supports enhanced power management feature in low power state with energy detection to ensure low-
power dissipation during device idle periods. There are four operation modes under the power management function
which is controlled by two bits in PMECR (0xD4) register as shown below:
PMECR[1:0] = 00 Normal Operation Mode
PMECR[1:0] = 01 Energy Detect Mode
PMECR[1:0] = 10 Soft Power Down Mode
PMECR[1:0] = 11 Power Saving Mode
Table 1 indicates all internal function blocks status under four different power management operation modes.
Power Management Operation Modes
KSZ8851M
Function Blocks
Normal mode
Power saving mode
Energy detect mode
Soft power down mode
Internal PLL Clock
Enabled
Disabled
Tx/Rx PHY
Enabled
Rx unused block disabled
Energy detect at Rx
Disabled
MAC
Enabled
Disabled
Host Interface
Enabled
Disabled
Table 1. Internal Function Blocks Status
Normal Operation Mode
This is the default setting bit[1:0]=00 in PMECR register after the chip power-up or hardware reset (pin 67). When
KSZ8851M is in this normal operation mode, all PLL clocks are running, PHY and MAC are on and the host interface is
ready for CPU read or write.
During the normal operation mode, the host CPU can set the bit[1:0] in PMECR register to transit the current normal
operation mode to any one of the other three power management operation modes.
Energy Detect Mode
The energy detect mode provides a mechanism to save more power than in the normal operation mode when the
KSZ8851M is not connected to an active link partner. For example, if cable is not present or it is connected to a powered
down partner, the KSZ8851M can automatically enter to the low power state in energy detect mode. Once activity
resumes due to plugging a cable or attempting by the far end to establish link, the KSZ8851M can automatically power up
to normal power state in energy detect mode.
Energy detect mode consists of two states, normal power state and low power state. While in low power state, the
KSZ8851M reduces power consumption by disabling all circuitry except the energy detect circuitry of the receiver. The
energy detect mode is entered by setting bit[1:0]=01 in PMECR register. When the KSZ8851M is in this mode, it will
monitor the cable energy. If there is no energy on the cable for a time longer than pre-configured value at bit[7:0] Go-
Sleep time in GSWUTR register, KSZ8851M will go into a low power state. When KSZ8851M is in low power state, it will
keep monitoring the cable energy. Once the energy is detected from the cable and is continuously presented for a time
longer than pre-configured value at bit[15:8] Wake-Up time in GSWUTR register, the KSZ8851M will enter either the
normal power state if the auto-wakeup enable bit[7] is set in PMECR register or the normal operation mode if both auto-
wakeup enable bit[7] and wakeup to normal operation mode bit[6] are set in PMECR register.
The KSZ8851M will also assert PME output pin if the corresponding enable bit[8] is set in PMECR (0xD4) register or
相关PDF资料 |
PDF描述 |
|---|---|
| LTC4278CDKD#PBF | IC PD IEEE 802.3AT 25.5W 32-DFN |
| KSZ8873MLL | IC ETHERNET SWITCH 3PORT 64-LQFP |
| KSZ8863RLL | IC ETHERNET SW 3PORT 48-LQFP |
| KSZ8863MLL | IC ETHERNET SW 3PORT 48-LQFP |
| KSZ8863FLL | IC ETHERNET SW 3PORT 48-LQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| KSZ8851-16MQL-EVAL | 功能描述:以太网开发工具 Single Ethernet Port + Generic (16-bit) Bus Interface(Lead Free) Eval Board RoHS:否 制造商:Micrel 产品:Evaluation Boards 类型:Ethernet Transceivers 工具用于评估:KSZ8873RLL 接口类型:RMII 工作电源电压: |
| KSZ8851-16MQLI | 功能描述:以太网 IC Single Ethernet Port + Generic (16-bit) Bus Interface(Lead Free, I-Temp) RoHS:否 制造商:Micrel 产品:Ethernet Switches 收发器数量:2 数据速率:10 Mb/s, 100 Mb/s 电源电压-最大:1.25 V, 3.45 V 电源电压-最小:1.15 V, 3.15 V 最大工作温度:+ 85 C 封装 / 箱体:QFN-64 封装:Tray |
| KSZ8851-32MQL | 功能描述:以太网 IC 10/100BT Ethernet MAC + PHY with Generic (32-bit) Bus Interface, Lead Free RoHS:否 制造商:Micrel 产品:Ethernet Switches 收发器数量:2 数据速率:10 Mb/s, 100 Mb/s 电源电压-最大:1.25 V, 3.45 V 电源电压-最小:1.15 V, 3.15 V 最大工作温度:+ 85 C 封装 / 箱体:QFN-64 封装:Tray |
| KSZ8851-32MQLI | 功能描述:以太网 IC 10/100BT Ethernet MAC + PHY with Generic (32-bit) Bus Interface (I-Temp) RoHS:否 制造商:Micrel 产品:Ethernet Switches 收发器数量:2 数据速率:10 Mb/s, 100 Mb/s 电源电压-最大:1.25 V, 3.45 V 电源电压-最小:1.15 V, 3.15 V 最大工作温度:+ 85 C 封装 / 箱体:QFN-64 封装:Tray |
| KSZ8851MLL | 制造商:MICREL 制造商全称:Micrel Semiconductor 功能描述:Single Port MAC/PHY Controller with Non PCI Interface |
发布紧急采购，3分钟左右您将得到回复。