参数资料
型号: KSZ8851-16MQL
厂商: Micrel Inc
文件页数: 41/88页
文件大小: 0K
描述: IC CTLR MAC/PHY NON-PCI 128-PQFP
产品培训模块: KSZ8851 10/100 Embedded Controllers
标准包装: 66
控制器类型: 以太网控制器,MAC/PHY
接口: 总线
电源电压: 1.8V,2.5V,3.3V
工作温度: 0°C ~ 70°C
安装类型: 表面贴装
封装/外壳: 128-BFQFP
供应商设备封装: 128-PQFP(14x20)
包装: 托盘
产品目录页面: 1081 (CN2011-ZH PDF)
配用: 576-3292-ND - BOARD EVALUATION KSZ8851-16MLL
其它名称: 576-3253
PIC16F8X
1998 Microchip Technology Inc.
DS30430C-page 47
8.7
Time-out Sequence and Power-down
Status Bits (TO/PD)
and Figure 8-13) the time-out sequence is as follows:
First PWRT time-out is invoked after a POR has
expired. Then the OST is activated. The total time-out
will vary based on oscillator configuration and PWRTE
configuration bit status. For example, in RC mode with
the PWRT disabled, there will be no time-out at all.
TABLE 8-5
TIME-OUT IN VARIOUS
SITUATIONS
Since the time-outs occur from the POR reset pulse, if
MCLR is kept low long enough, the time-outs will
expire. Then bringing MCLR high, execution will begin
immediately (Figure 8-10). This is useful for testing
purposes or to synchronize more than one PIC16F8X
device when operating in parallel.
Table 8-6 shows the significance of the TO and PD bits.
Table 8-3 lists the reset conditions for some special
registers, while Table 8-4 lists the reset conditions for
all the registers.
TABLE 8-6
STATUS BITS AND THEIR
SIGNIFICANCE
8.8
Reset on Brown-Out
A brown-out is a condition where device power (VDD)
dips below its minimum value, but not to zero, and then
recovers. The device should be reset in the event of a
brown-out.
To reset a PIC16F8X device when a brown-out occurs,
external brown-out protection circuits may be built, as
FIGURE 8-14: BROWN-OUT PROTECTION
CIRCUIT 1
FIGURE 8-15: BROWN-OUT PROTECTION
CIRCUIT 2
Oscillator
Configuration
Power-up
Wake-up
from
SLEEP
PWRT
Enabled
PWRT
Disabled
XT, HS, LP
72 ms +
1024TOSC
RC
72 ms
——
TO
PD
Condition
11
Power-on Reset
0x
Illegal, TO is set on POR
x0
Illegal, PD is set on POR
01
WDT Reset (during normal operation)
00
WDT Wake-up
11
MCLR Reset during normal operation
10
MCLR Reset during SLEEP or interrupt
wake-up from SLEEP
This circuit will activate reset when VDD goes below
(Vz + 0.7V) where Vz = Zener voltage.
VDD
33k
10k
40k
VDD
MCLR
PIC16F8X
This brown-out circuit is less expensive, although less
accurate. Transistor Q1 turns off when VDD is below a
certain level such that:
VDD
R1
R1 + R2
= 0.7V
R2
40k
VDD
MCLR
PIC16F8X
R1
Q1
VDD
相关PDF资料
PDF描述
LTC4278CDKD#PBF IC PD IEEE 802.3AT 25.5W 32-DFN
KSZ8873MLL IC ETHERNET SWITCH 3PORT 64-LQFP
KSZ8863RLL IC ETHERNET SW 3PORT 48-LQFP
KSZ8863MLL IC ETHERNET SW 3PORT 48-LQFP
KSZ8863FLL IC ETHERNET SW 3PORT 48-LQFP
相关代理商/技术参数
参数描述
KSZ8851-16MQL-EVAL 功能描述:以太网开发工具 Single Ethernet Port + Generic (16-bit) Bus Interface(Lead Free) Eval Board RoHS:否 制造商:Micrel 产品:Evaluation Boards 类型:Ethernet Transceivers 工具用于评估:KSZ8873RLL 接口类型:RMII 工作电源电压:
KSZ8851-16MQLI 功能描述:以太网 IC Single Ethernet Port + Generic (16-bit) Bus Interface(Lead Free, I-Temp) RoHS:否 制造商:Micrel 产品:Ethernet Switches 收发器数量:2 数据速率:10 Mb/s, 100 Mb/s 电源电压-最大:1.25 V, 3.45 V 电源电压-最小:1.15 V, 3.15 V 最大工作温度:+ 85 C 封装 / 箱体:QFN-64 封装:Tray
KSZ8851-32MQL 功能描述:以太网 IC 10/100BT Ethernet MAC + PHY with Generic (32-bit) Bus Interface, Lead Free RoHS:否 制造商:Micrel 产品:Ethernet Switches 收发器数量:2 数据速率:10 Mb/s, 100 Mb/s 电源电压-最大:1.25 V, 3.45 V 电源电压-最小:1.15 V, 3.15 V 最大工作温度:+ 85 C 封装 / 箱体:QFN-64 封装:Tray
KSZ8851-32MQLI 功能描述:以太网 IC 10/100BT Ethernet MAC + PHY with Generic (32-bit) Bus Interface (I-Temp) RoHS:否 制造商:Micrel 产品:Ethernet Switches 收发器数量:2 数据速率:10 Mb/s, 100 Mb/s 电源电压-最大:1.25 V, 3.45 V 电源电压-最小:1.15 V, 3.15 V 最大工作温度:+ 85 C 封装 / 箱体:QFN-64 封装:Tray
KSZ8851MLL 制造商:MICREL 制造商全称:Micrel Semiconductor 功能描述:Single Port MAC/PHY Controller with Non PCI Interface