- 您现在的位置：买卖IC网 > PDF目录32287 > L6740L (STMICROELECTRONICS) SPECIALTY ANALOG CIRCUIT, PQFP48 PDF资料下载
参数资料
| 型号： | L6740L |
| 厂商： | STMICROELECTRONICS |
| 元件分类： | 模拟信号调理 |
| 英文描述： | SPECIALTY ANALOG CIRCUIT, PQFP48 |
| 封装： | 7 X 7 MM, 1 MM HEIGHT, HTQFP-48 |
| 文件页数： | 14/44页 |
| 文件大小： | 755K |
| 代理商： | L6740L |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页当前第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页
L6740L
Hybrid CPU support and CPU_TYPE detection
5.4.2
PWROK de-assertion
Anytime PWROK de-asserts while EN is asserted, the controller uses the previously stored
Pre-PWROK Metal VID and regulates all the planes to that level performing an On-the-Fly
transition to that level.
PWRGOOD is treated appropriately being de-asserted in case the Pre-PWROK Metal VID
voltage is out of the initial voltage specifications.
5.4.3
PSI_L and efficiency optimization at light-load
PSI_L is an active-low flag (i.e. low logic level when asserted) that can be set by the CPU to
allow the VR to enter power-saving mode to maximize the system efficiency when in light-
load conditions. The status of the flag is communicated to the controller through the SVI bus
and it is reported on the PSI_L pin (open-drain).
The controller monitors the PSI_L pin also to define the PSI Strategy, that is the action
performed by the controller when PSI_L is asserted. According to Table 10, by programming
different voltage divider on PSI_L, it is possible to configure the device to disable one or two
phases while PSI_L is asserted. The device can also be configured to take no action so
phase number will not change after PSI_L assertion.
In case the phase number is changed, the device will disable one or two phases starting
from the highest one (i.e. if working at 3 phases, phase 3 will be disabled in case of 1 phase
reduction; phase 2 and 3 in case of 2phase reduction). To disable Phases, the controller will
set HiZ on the related PWM and re-configure internal phase-shift to maintain the
interleaving. Furthermore, the internal current-sharing will be adjusted to consider the phase
number reduction. ENDRV will remain asserted.
When PSI_L is de-asserted, the device will return to the original configuration.
Start-up is performed with all the configured phases enabled. In case of on-the-fly VID
transitions, the device will maintain the phase configuration set before.
PSI strategy (i.e. the voltage across PSI_L) is read and stored when PWRGOOD is
asserted at the end of the Soft-Start phase.
The phase number management is affected by the external driver selected.
●
If the external driver features the EN function, PSI_L can be tied directly to the EN of
the drivers of the phases that will be disabled.
Furthermore, in case the desired strategy is to work in single phase when 4phases are
configured, PSI_L can be tied also to the EN of the driver connected to Phase2
(apparently, from 4phases the max reduction would be to 2phase min.) in order to
disable also this phase during low-power mode.
●
If the external driver manages HiZ through the PWM input, PSI_L will be connected
only to the external divider used to set the strategy. The system can be down-graded to
single-phase only if configured for three phases.
Since PSI_L can be used to enable some of the external drivers connected, the status of the
pin is the logic AND between the PSI_L Flag and the status of the ENDRV pin: if the
controller wants to disable the external drivers pulling low ENDRV (because of protections
or simply for start-up synchronization) also PSI_L will be tied low.
NB section is not impacted by PSI_L status change. Figure 8 shows an example of the
efficiency improvement that can be achieved by enabling the PSI management.
相关PDF资料 |
PDF描述 |
|---|---|
| L9705D013TR | SPECIALTY ANALOG CIRCUIT, PDSO20 |
| L9953LXPTR | SPECIALTY CONSUMER CIRCUIT, PDSO36 |
| L9953LXP | SPECIALTY CONSUMER CIRCUIT, PDSO36 |
| LA1177 | 1-BAND, AUDIO TUNER, PSIP9 |
| LA1178M | 1-BAND, AUDIO TUNER, PDSO10 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| L6740LTR | 功能描述:DC/DC 开关控制器 Hybrid controller RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| L6741 | 功能描述:功率驱动器IC SnglPphase Dual MOSFET Driver RoHS:否 制造商:Micrel 产品:MOSFET Gate Drivers 类型:Low Cost High or Low Side MOSFET Driver 上升时间: 下降时间: 电源电压-最大:30 V 电源电压-最小:2.75 V 电源电流: 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube |
| L6741TR | 功能描述:功率驱动器IC SnglPphase Dual MOSFET Driver RoHS:否 制造商:Micrel 产品:MOSFET Gate Drivers 类型:Low Cost High or Low Side MOSFET Driver 上升时间: 下降时间: 电源电压-最大:30 V 电源电压-最小:2.75 V 电源电流: 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube |
| L6743 | 功能描述:功率驱动器IC SnglPphase Dual MOSFET Driver RoHS:否 制造商:Micrel 产品:MOSFET Gate Drivers 类型:Low Cost High or Low Side MOSFET Driver 上升时间: 下降时间: 电源电压-最大:30 V 电源电压-最小:2.75 V 电源电流: 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube |
| L6743_08 | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:High current MOSFET driver |
发布紧急采购，3分钟左右您将得到回复。