- 您现在的位置：买卖IC网 > PDF目录13065 > LTC3734EUH#TR (Linear Technology)IC CTRLR DC/DC 1PH HI EFF 32QFN PDF资料下载
参数资料
| 型号： | LTC3734EUH#TR |
| 厂商： | Linear Technology |
| 文件页数： | 24/28页 |
| 文件大小： | 0K |
| 描述： | IC CTRLR DC/DC 1PH HI EFF 32QFN |
| 标准包装： | 2,500 |
| 应用： | 控制器，Intel 移动式 CPU |
| 输入电压： | 4 V ~ 30 V |
| 输出数： | 1 |
| 输出电压： | 0.7 V ~ 1.71 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-WFQFN 裸露焊盘 |
| 供应商设备封装： | 32-QFN 裸露焊盘（5x5） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页当前第24页第25页第26页第27页第28页
LTC3734
APPLICATIONS INFORMATION
PC Board Layout Checklist
When laying out the printed circuit board, the following
checklist should be used to ensure proper operation of
the LTC3734. Check the following in your layout:
1) Are the signal and power grounds segregated? Keep
the SGND at one end of a PC board to prevent MOSFET
currents from traveling under the IC. The IC signal ground
pin (Pin 5) should be used to hook up all control circuitry
on one side of the IC, routing the copper through SGND,
under the IC covering the “shadow” of the package, con-
necting to the PGND pin (Pin 20) and then continuing on
to the (–) plate of C OUT .
2) Is the PV CC decoupling capacitor connected immedi-
ately adjacent to the PV CC and PGND pins? A 1μF ceramic
capacitor of the X7R or X5R material is small enough to
fit very close to the IC to minimize the ill effects of the
large current pulses drawn to drive the power MOSFETs.
An additional 4.7μF ~ 10μF of ceramic, tantalum or other
low ESR capacitor is recommended in order to keep PV CC
stable. The power ground returns to the sources of the bot-
tom N-channel MOSFETs, anodes of the Schottky diodes,
and (–) plates of C IN , which should have the shortest trace
length possible.
3) Are the SENSE – and SENSE + leads routed together
with minimum PC trace spacing? The filter capacitors
between SENSE + and SENSE – pin pairs should be as
close as possible to the LTC3734. Ensure accurate cur-
rent sensing with Kelvin connections at the current sense
resistor. See Figure 8.
4) Does the (+) plate of C IN connect to the drains of the
topside MOSFETs as closely as possible? This capacitor
provides the AC current to the MOSFETs. Keep the input
current path formed by the input capacitor, top and bot-
tom MOSFETs, and the Schottky diode on the same side
of the PC board in a tight loop to minimize conducted and
radiated EMI.
5) Keep the “noisy” nodes, SW, BOOST, TG and BG away
from sensitive small-signal nodes. Ideally the switch
nodes should be placed at the furthest point from the
LTC3734.
It is critical to keep the high-switching-current paths to a
small physical size. High electric and magnetic fields will
radiate from these “loops” just as radio stations transmit
signals. The output capacitor ground should return to the
negative terminal of the input capacitor and not share a
common ground path with any switched current paths.
The left half of the circuit gives rise to the “noise” gener-
ated by a switching regulator. The ground terminations
of the sychronous MOSFETs and Schottky diodes should
return to the negative plate(s) of the input capacitor(s)
with a short isolated PC trace since very high switched
currents are present. A separate isolated path from the
negative plate(s) of the input capacitor(s) should be used
to tie in the IC power ground pin (PGND) and the signal
ground pin (SGND). This technique keeps inherent signals
generated by high current pulses from taking alternate
current paths that have finite impedances during the total
period of the switching regulator. External OPTI-LOOP
compensation allows overcompensation for PC layouts
which are not optimized but this is not the recommended
design procedure.
PADS OF SENSE RESISTOR
TRACE TO INDUCTOR
SENSE +
SENSE –
TRACE TO OUTPUT CAP (+)
3734 F08
Figure 8. Proper Current Sense Connections
3734fa
24
相关PDF资料 |
PDF描述 |
|---|---|
| C0603X7R1E222M | CAP CER 2200PF 25V 20% X7R 0201 |
| LTC3720EGN#TR | IC STP-DN CNTRLR SNGL-PHS 28SSOP |
| UWZ1E151MCL1GS | CAP ALUM 150UF 25V 20% SMD |
| LT1184CS#TRPBF | IC SW REG CCFL CONTRAST 16-SOIC |
| 450USC150MEFCSN25X30 | CAP ALUM 150UF 450V 20% SNAP-IN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC3735EG | 功能描述:IC CTRLR DC/DC 2PH HI EFF 36SSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:43 系列:- 应用:控制器，Intel VR11 输入电压:5 V ~ 12 V 输出数:1 输出电压:0.5 V ~ 1.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商设备封装:48-QFN（7x7） 包装:管件 |
| LTC3735EG#PBF | 功能描述:IC CTRLR DC/DC 2PH HI EFF 36SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:2,000 系列:- 应用:控制器，DSP 输入电压:4.5 V ~ 25 V 输出数:2 输出电压:最低可调至 1.2V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:30-TFSOP（0.173"，4.40mm 宽） 供应商设备封装:30-TSSOP 包装:带卷 (TR) |
| LTC3735EG#TR | 功能描述:IC CTRLR DC/DC 2PH HI EFF 36SSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:43 系列:- 应用:控制器，Intel VR11 输入电压:5 V ~ 12 V 输出数:1 输出电压:0.5 V ~ 1.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商设备封装:48-QFN（7x7） 包装:管件 |
| LTC3735EG#TRPBF | 功能描述:IC CTRLR DC/DC 2PH HI EFF 36SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:43 系列:- 应用:控制器，Intel VR11 输入电压:5 V ~ 12 V 输出数:1 输出电压:0.5 V ~ 1.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商设备封装:48-QFN（7x7） 包装:管件 |
| LTC3735EUHF | 功能描述:IC CTRLR DC/DC 2PH HI EFF 38-QFN RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:43 系列:- 应用:控制器，Intel VR11 输入电压:5 V ~ 12 V 输出数:1 输出电压:0.5 V ~ 1.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商设备封装:48-QFN（7x7） 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。