参数资料
型号: LTC4155IUFD#TRPBF
厂商: Linear Technology
文件页数: 22/52页
文件大小: 0K
描述: IC I2C POWER MANAGER DUAL 28QFN
标准包装: 2,500
系列: PowerPath™
功能: 充电管理,电源管理
电池化学: 锂离子(Li-Ion)、锂聚合物(Li-Pol)
电源电压: 4.35 V ~ 5.5 V
工作温度: -40°C ~ 125°C
安装类型: 表面贴装
封装/外壳: 28-WFQFN 裸露焊盘
供应商设备封装: 28-QFN(4x5)
包装: 带卷 (TR)
LTC4155
OPERATION
WALLSNS pins. The voltage threshold values previously
listed and specified in the Electrical Characteristics table
are valid when each input is connected to its respective
sense pin through a 3.6k resistor.
The status of the USB and WALL inputs is monitored
continuously and reported by I 2 C, with the option of
generating several interrupts. When all three conditions
previously listed are true, the LTC4155 will report the input
valid by asserting USBSNSGD or WALLSNSGD in the I 2 C
port. Optionally, if external power interrupts are enabled,
an interrupt request will be generated.
When power is applied simultaneously to both inputs,
the LTC4155 will draw power from the WALL input by
default. If the I 2 C PRIORITY bit is asserted, the LTC4155
will instead draw power from the USB input when both
inputs are present. The USB On-The-Go step-up regulator
delivers power only to the USB input, and the PRIOR-
ITY bit is ignored in this mode. The input current limits
USBILIM[4:0] and WALLILIM[4:0] also reset to 100mA
If overvoltage protection is not necessary in the application,
connect USBSNS to V BUS with a 3.6k resistor, as shown
in Figure 3. If the USB On-The-Go step-up regulator is
not used in the application, it is also possible to connect
WALLSNS to V BUS through 3.6k and leave USBSNS open.
100mA Linear Battery Charger Mode
The LTC4155 features a mode to support USB low power
operation. Total input current to the LTC4155 is guaranteed
to remain below 100mA in this mode when the recom-
mended resistor is used on the CLPROG2 pin. The step-
down switching regulator does not operate in this mode.
Instead, a linear regulator provides power from V BUS to
V OUT and the battery. The linear battery charger follows
the same constant-current/constant-voltage algorithm as
the switching regulator, but regulates input current rather
than battery charge current. The voltage on the CLPROG2
pin represents the input current in this mode, using the
expression:
default mode under different criteria. In all other respects,
the two inputs are identical.
I VBUS =
V CLPROG2
R CLPROG2
? ( 80 )
An optional capacitor may be placed between the OVGCAP
pin and GND to minimize input current disruption when
switching from one input to the other while operating at
Battery charge current is represented by the voltage on
the PROG pin, but it is not regulated in this mode.
high power levels. The capacitor must be rated to withstand
at least 13V and should be approximately ten times larger
than the total gate capacitance of the series NMOS power
I CHARGE =
V PROG
R PROG
? ( 1000 )
transistors. Capacitance on this pin can also be used to
slow the gate charging if the application requires controlled
inrush current to any additional input capacitance on the
V BUS pin. If fast switching between input or inrush control
is not necessary, OVGCAP may be left unconnected.
V OUT will generally be very close to the battery voltage when
the battery charger is enabled, except when the battery
voltage is very low, the LTC4155 will increase the imped-
ance between V OUT and BATSNS to facilitate instant-on
operation. If the system load plus battery charge current
exceeds the available input current, battery charge current
TO POWER
INPUT
R1
WALLSNS
WALLGT
LTC4155
V BUS
USBGT
USBSNS
OVGCAP
4155 F03
will be sacrificed to give priority to the load. If the system
load alone exceeds the available input current, V OUT must
fall to the battery voltage so that the battery may provide
the supplemental current.
The battery will charge to the float voltage specified by
the I 2 C setting VFLOAT[1:0]. See Table 12.
When the battery charger is disabled or terminated, V OUT
will be regulated to 4.35V.
Figure 3. No Overvoltage Protection
4155fc
22
相关PDF资料
PDF描述
LTC4160EUDC-1#TRPBF IC SWITCH POWER MANAGER 20-QFN
LTC4410ES6#TRPBF IC POWER MANAGER USB TSOT23-6
LTC4411ES5#TRMPBF IC IDEAL DIODE LOW LOSS TSOT23-5
LTC4412IS6#TRMPBF IC PWR PATH CNTRLR TSOT23-6
LTC4413EDD-1#PBF IC IDEAL DIODE DUAL 10-DFN
相关代理商/技术参数
参数描述
LTC4156EUFD#PBF 功能描述:IC POWER LI-ION CHARGER 28-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:* 其它有关文件:STC3100 View All Specifications 特色产品:STC3100 - Battery Monitor IC 标准包装:4,000 系列:- 功能:燃料,电量检测计/监控器 电池化学:锂离子(Li-Ion) 电源电压:2.7 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-TSSOP,8-MSOP(0.118",3.00mm 宽) 供应商设备封装:8-MiniSO 包装:带卷 (TR) 其它名称:497-10526-2
LTC4156EUFD#TRPBF 功能描述:IC POWER LI-ION CHARGER 28-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:* 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 功能:电池监控器 电池化学:碱性,锂离子,镍镉,镍金属氢化物 电源电压:1 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-6 包装:带卷 (TR)
LTC4156IUFD#PBF 功能描述:IC POWER LI-ION CHARGER 28-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:* 其它有关文件:STC3100 View All Specifications 特色产品:STC3100 - Battery Monitor IC 标准包装:4,000 系列:- 功能:燃料,电量检测计/监控器 电池化学:锂离子(Li-Ion) 电源电压:2.7 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-TSSOP,8-MSOP(0.118",3.00mm 宽) 供应商设备封装:8-MiniSO 包装:带卷 (TR) 其它名称:497-10526-2
LTC4156IUFD#TRPBF 功能描述:IC POWER LI-ION CHARGER 28-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:* 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 功能:电池监控器 电池化学:碱性,锂离子,镍镉,镍金属氢化物 电源电压:1 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-6 包装:带卷 (TR)
LTC4160 制造商:LINER 制造商全称:Linear Technology 功能描述:Switching Power Manager with USB On-The-Go And Overvoltage Protection