- 您现在的位置：买卖IC网 > PDF目录1834 > LTC4160EUDC-1#TRPBF (Linear Technology)IC SWITCH POWER MANAGER 20-QFN PDF资料下载
参数资料
| 型号： | LTC4160EUDC-1#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 15/32页 |
| 文件大小： | 0K |
| 描述： | IC SWITCH POWER MANAGER 20-QFN |
| 标准包装： | 2,500 |
| 系列： | Bat-Track™, PowerPath™ |
| 功能： | 电源管理 |
| 电池化学： | 锂离子（Li-Ion）、锂聚合物（Li-Pol） |
| 电源电压： | 4.35 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-WFQFN 裸露焊盘 |
| 供应商设备封装： | 20-QFN（3x4） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页当前第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页
LTC4160/LTC4160-1
OPERATION
For very low-battery voltages, the battery charger acts like
a load and, due to limited input power, its current will tend
to pull V OUT below the 3.6V instant-on voltage. To prevent
V OUT from falling below this level, an undervoltage circuit
automatically detects that V OUT is falling and reduces the
battery charge current as needed. This reduction ensures
that load current and voltage are always prioritized while
allowing as much battery charge current as possible. See
Over Programming the Battery Charger in the Applications
Information section.
The voltage regulation loop compensation is controlled by
the capacitance on V OUT . A multilayer ceramic capacitor of
10μF is required for loop stability. Additional capacitance
beyond this value will improve transient response.
An internal undervoltage lockout circuit monitors V BUS and
keeps the switching regulator off until V BUS rises above
4.30V and is about 200mV above the battery voltage.
When both conditions are met, VBUSGD goes low and
the switching regulator turns on. Hysteresis on the UVLO
forces VBUSGD high and turns off the switching regulator
if V BUS falls below 4.00V or to within 50mV of the battery
voltage. When this happens, system power at V OUT will
be drawn from the battery via the ideal diode(s).
4.5
4.2
3.9
NO LOAD
3.6
300mV
3.3
3.0
2.7
2.4
2.4 2.7 3.0 3.3 3.6 3.9 4.2
BAT (V)
41601 F02
Figure 2. V OUT vs BAT
Bidirectional PowerPath Switching Regulator –
Step-Up Mode
For USB On-The-Go applications, the bidirectional
PowerPath switching regulator acts as a step-up converter
to deliver power from V OUT to V BUS . The power from V OUT
comes from the battery via the ideal diode(s). As a step-up
converter, the bidirectional switching regulator produces
5V on V BUS and is capable of delivering at least 500mA.
USB On-The-Go can be enabled by either of the external
control pins, ENOTG or ID. Figure 3 shows the power flow
in step-up mode.
An undervoltage lockout circuit monitors V OUT and prevents
step-up conversion until V OUT rises above 2.8V. To prevent
backdriving of V BUS when input power is available, the V BUS
undervoltage lockout circuit prevents step-up conversion
if V BUS is already greater than 4.3V at the time step-up
mode is enabled. The switching regulator is also designed
to allow true output disconnect by eliminating body diode
conduction of the internal PMOS switch. This allows V BUS
to go to zero volts during a short-circuit condition or while
shutdown, drawing zero current from V OUT .
The voltage regulation loop is compensated by the capaci-
tance on V BUS . A 4.7μF multilayer ceramic capacitor is
required for loop stability. Additional capacitance beyond
this value will improve transient response. The V BUS volt-
age has approximately 3% load regulation up to an output
current of 500mA. At light loads, the switching regulator
goes into Burst Mode ? operation. The regulator will deliver
power to V BUS until it reaches 5.1V after which the NMOS
and PMOS switches shut off. The regulator delivers power
again to V BUS once it falls below 5.1V.
The switching regulator features both peak inductor and
average output current limit. The peak current-mode
architecture limits peak inductor current on a cycle-by-
cycle basis. The peak current limit is equal to V BUS /2Ω to
a maximum of 1.8A so that in the event of a sudden short
circuit, the current limit will fold back to a lower value.
In step-up mode, the voltage on CLPROG represents the
average output current of the switching regulator when
a programming resistor and an averaging capacitor are
connected from CLPROG to GND. With a 3.01k resistor
on CLPROG, the bidirectional switching regulator has an
output current limit of 680mA. As the output current ap-
proaches this limit, CLPROG servos to 1.15V and V BUS falls
rapidly to V OUT . When V BUS is close to V OUT there may not
be sufficient negative slope on the inductor current when
the PMOS switch is on to balance the rise in the inductor
41601f
15
相关PDF资料 |
PDF描述 |
|---|---|
| LTC4410ES6#TRPBF | IC POWER MANAGER USB TSOT23-6 |
| LTC4411ES5#TRMPBF | IC IDEAL DIODE LOW LOSS TSOT23-5 |
| LTC4412IS6#TRMPBF | IC PWR PATH CNTRLR TSOT23-6 |
| LTC4413EDD-1#PBF | IC IDEAL DIODE DUAL 10-DFN |
| LTC4413EDD#PBF | IC IDEAL DIODE DUAL 10-DFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC4210 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Dual Supply Hot Swap Controller for Advanced Mezzanine Card |
| LTC4210-1 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Hot Swap Controller in 6-Lead SOT-23 Package |
| LTC42101CS6 | 制造商:Linear Technology 功能描述: |
| LTC4210-1CS6 | 制造商:Linear Technology 功能描述:Hot Swap Controller 1-CH 16.5V 6-Pin TSOT-23 |
| LTC4210-1CS6#PBF | 制造商:Linear Technology 功能描述:Hot Swap Controller 1-CH 16.5V 6-Pin TSOT-23 制造商:Linear Technology 功能描述:IC HOT SWAP CONT 制造商:Linear Technology 功能描述:HOT SWAP CNTRL 16.5VIN 6SOT23 制造商:Linear Technology 功能描述:HOT SWAP, CNTRL, 16.5VIN, 6SOT23 制造商:Linear Technology 功能描述:IC, HOT SWAP CONT; Controller Applications:Hot Board Insertion, Electronic Circuit Breaker, Industrial High Side Switch; Input Voltage:16.5V; Internal Switch:Yes; Supply Voltage Min:2.7V; Supply Voltage Max:16.5V; No. of Pins:6 ;RoHS Compliant: Yes |
发布紧急采购，3分钟左右您将得到回复。