- 您现在的位置：买卖IC网 > PDF目录1834 > LTC4160EUDC-1#TRPBF (Linear Technology)IC SWITCH POWER MANAGER 20-QFN PDF资料下载
参数资料
| 型号： | LTC4160EUDC-1#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 17/32页 |
| 文件大小： | 0K |
| 描述： | IC SWITCH POWER MANAGER 20-QFN |
| 标准包装： | 2,500 |
| 系列： | Bat-Track™, PowerPath™ |
| 功能： | 电源管理 |
| 电池化学： | 锂离子（Li-Ion）、锂聚合物（Li-Pol） |
| 电源电压： | 4.35 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-WFQFN 裸露焊盘 |
| 供应商设备封装： | 20-QFN（3x4） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页当前第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页
LTC4160/LTC4160-1
OPERATION
the voltage at V OUT is approximately 15mV (V FWD ) below
the voltage at BAT. Within the amplifier’s linear range, the
small-signal resistance of the ideal diode will be quite low,
keeping the forward drop near 15mV. At higher current
levels, the MOSFET will be in full conduction.
To supplement the internal ideal diode, an external P-
channel MOSFET may be added from BAT to V OUT . The
IDGATE pin of the LTC4160/LTC4160-1 drives the gate of
the external P-channel MOSFET for automatic ideal diode
control. The source of the external P-channel MOSFET
should be connected to V OUT and the drain should be con-
nected to BAT. Capable of driving a 1nF load, the IDGATE
pin can control an external P-channel MOSFET having an
on-resistance of 30m? or lower.
Suspend LDO
If the LTC4160/LTC4160-1 is configured for USB suspend
mode, the bidirectional switching regulator is disabled and
the suspend LDO provides power to the V OUT pin (pre-
suming there is power available at V BUS ). This LDO will
prevent the battery from running down when the portable
product has access to a suspended USB port. Regulating at
4.6V, this LDO only becomes active when the bidirectional
switching regulator is disabled (suspended). The sus-
pend LDO sends a scaled copy of the V BUS current to the
CLPROG pin, which will servo to approximately 100mV in
this mode. In accordance with the USB specification, the
input to the LDO is current limited so that it will not exceed
the low power suspend specification. If the load on V OUT
exceeds the suspend current limit, the additional current
will come from the battery via the ideal diode(s).
3.3V Always-On LDO Supply
The LTC4160/LTC4160-1 include a low quiescent current
low dropout regulator that is always powered. This LDO
can be used to provide power to a system pushbutton
controller, standby microcontroller or real time clock.
Designed to deliver up to 20mA, the always-on LDO re-
quires at least a 1μF multilayer ceramic bypass capacitor
for compensation. The LDO is powered from V OUT , and
therefore will enter dropout at loads less than 20mA as
V OUT falls near 3.3V. If the LDO3V3 output is not used, it
should be disabled by connecting it to V OUT .
Battery Charger
The LTC4160/LTC4160-1 include a constant-current/con-
stant-voltage battery charger with automatic recharge,
automatic termination by safety timer, low voltage trickle
charging, bad cell detection, and thermistor sensor input
for out-of-temperature charge pausing. The charger can
be disabled using the ENCHARGER pin.
Battery Preconditioning
When a battery charge cycle begins, the battery charger
first determines if the battery is deeply discharged. If the
battery voltage is below V TRKL , typically 2.85V, an automatic
trickle charge feature sets the battery charge current to
10% of the programmed value. If the low voltage persists
for more than a 1/2 hour, the battery charger automatically
terminates and indicates via the CHRG and FAULT pins that
the battery was unresponsive.
Once the battery voltage is above 2.85V, the charger begins
charging in full power constant-current mode. The cur-
rent delivered to the battery will try to reach 1030/R PROG .
Depending on available input power and external load
conditions, the battery charger may or may not be able
to charge at the full programmed rate. The external load
will always be prioritized over the battery charge current.
Likewise, the USB current limit programming will always
be observed and only additional power will be available to
charge the battery. When system loads are light, battery
charge current will be maximized.
Charge Termination
The battery charger has a built-in safety timer. When the
voltage on the battery reaches the pre-programmed float
voltage, the battery charger will regulate the battery volt-
age and the charge current will decrease naturally. Once
the battery charger detects that the battery has reached
the float voltage, the four hour safety timer is started.
After the safety timer expires, charging of the battery will
discontinue and no more current will be delivered.
Automatic Recharge
After the battery charger terminates, it will remain off
drawing only microamperes of current from the battery.
If the portable product remains in this state long enough,
41601fa
17
相关PDF资料 |
PDF描述 |
|---|---|
| LTC4410ES6#TRPBF | IC POWER MANAGER USB TSOT23-6 |
| LTC4411ES5#TRMPBF | IC IDEAL DIODE LOW LOSS TSOT23-5 |
| LTC4412IS6#TRMPBF | IC PWR PATH CNTRLR TSOT23-6 |
| LTC4413EDD-1#PBF | IC IDEAL DIODE DUAL 10-DFN |
| LTC4413EDD#PBF | IC IDEAL DIODE DUAL 10-DFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC4210 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Dual Supply Hot Swap Controller for Advanced Mezzanine Card |
| LTC4210-1 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Hot Swap Controller in 6-Lead SOT-23 Package |
| LTC42101CS6 | 制造商:Linear Technology 功能描述: |
| LTC4210-1CS6 | 制造商:Linear Technology 功能描述:Hot Swap Controller 1-CH 16.5V 6-Pin TSOT-23 |
| LTC4210-1CS6#PBF | 制造商:Linear Technology 功能描述:Hot Swap Controller 1-CH 16.5V 6-Pin TSOT-23 制造商:Linear Technology 功能描述:IC HOT SWAP CONT 制造商:Linear Technology 功能描述:HOT SWAP CNTRL 16.5VIN 6SOT23 制造商:Linear Technology 功能描述:HOT SWAP, CNTRL, 16.5VIN, 6SOT23 制造商:Linear Technology 功能描述:IC, HOT SWAP CONT; Controller Applications:Hot Board Insertion, Electronic Circuit Breaker, Industrial High Side Switch; Input Voltage:16.5V; Internal Switch:Yes; Supply Voltage Min:2.7V; Supply Voltage Max:16.5V; No. of Pins:6 ;RoHS Compliant: Yes |
发布紧急采购，3分钟左右您将得到回复。