- 您现在的位置：买卖IC网 > PDF目录80446 > M38D24G6-XXXFP 8-BIT, FLASH, 6.25 MHz, MICROCONTROLLER, PQFP64 PDF资料下载
参数资料
| 型号： | M38D24G6-XXXFP |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 8-BIT, FLASH, 6.25 MHz, MICROCONTROLLER, PQFP64 |
| 封装： | 14 X 14 MM, 0.80 MM PITCH, PLASTIC, LQFP-64 |
| 文件页数： | 25/136页 |
| 文件大小： | 2856K |
| 代理商： | M38D24G6-XXXFP |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页当前第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页第129页第130页第131页第132页第133页第134页第135页第136页
Rev.3.02
Apr 10, 2008
Page 120 of 131
REJ03B0177-0302
38D2 Group
3. Direction Registers
4. Pull-Up Control
Only for the pin set to input mode, pull-up is controlled by the
PULL register and the segment output disable register.
Notes on Termination of Unused Pins
1. Termination of Unused Pins
Perform the following at the shortest possible distance (20 mm or
less) from the MCU pins.
(1) I/O ports
Set the ports to input mode and connect each pin to VCC or VSS
through a resistor of 1 k to 10 k
Ω. An internal pull-up resistor can
also be used for the port where the internal pull-up resister is
selectable.
To set the ports to output mode, leave open at “L” or “H” output.
When setting the ports to output mode and leave open,
input mode in the initial state remains until the mode of the
ports are switched to output mode by a program after a
reset. This may cause the voltage level of the pins to be
undefined and the power source current to increase while
the ports remains in input mode. For any effects on the
system, careful system evaluations should be implemented
on the user side.
The direction registers may be changed due to a program
runaway or noise, so reset the registers periodically by a
program to increase the program reliability.
2. Termination Concerns
(1) When setting I/O ports to input mode
[1] Do not leave open
<Reason>
The power source current may increase depending on the
first-stage circuit.
The ports are more likely affected by noise when compared
with the termination shown on the above “1. (1) I/O ports”
[2] Do not connect to VCC or VSS directly
<Reason>
If the direction registers are changed to output mode due to a
program runaway or noise, a short circuit may occur.
[3] Do not connect multiple ports in a lump to VCC or VSS
through a resistor.
<Reason>
If the direction registers are changed to output mode due to a
program runaway or noise, a short circuit may occur between the
ports.
相关PDF资料 |
PDF描述 |
|---|---|
| MC68HC705MC4MS | 8-BIT, UVPROM, 3 MHz, MICROCONTROLLER, CDIP28 |
| MPC8270VRMHBX | 32-BIT, 266 MHz, RISC PROCESSOR, PBGA516 |
| MC9S12HZ64VFU | 16-BIT, FLASH, 25 MHz, MICROCONTROLLER, PQFP80 |
| MC6805P6P | 8-BIT, MROM, 1 MHz, MICROCONTROLLER, PDIP28 |
| MC6805S2P | 8-BIT, MROM, MICROCONTROLLER, PDIP28 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| M38D24G6XXXHP | 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M38D24G7XXXFP | 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M38D24G7XXXHP | 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M38D24G8XXXFP | 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M38D24G8XXXHP | 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
发布紧急采购，3分钟左右您将得到回复。