- 您现在的位置：买卖IC网 > Datasheet目录340 > MAX15018BASA+ (Maxim Integrated Products)IC MOSF DRVR HALF BRDG HS 8-SOIC Datasheet资料下载
参数资料
| 型号： | MAX15018BASA+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 10/14页 |
| 文件大小： | 0K |
| 描述： | IC MOSF DRVR HALF BRDG HS 8-SOIC |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 100 |
| 配置： | 半桥 |
| 输入类型： | 反相和非反相 |
| 延迟时间： | 33ns |
| 电流 - 峰： | 3A |
| 配置数： | 1 |
| 输出数： | 2 |
| 高端电压 - 最大（自引导启动）： | 125V |
| 电源电压： | 8 V ~ 12.6 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm Width）裸露焊盘 |
| 供应商设备封装： | 8-SOICN 裸露焊盘 |
| 包装： | 管件 |
125V/3A, High-Speed,
Half-Bridge MOSFET Drivers
Bootstrap Capacitor
The bootstrap capacitor is used to ensure adequate
charge is available to switch the high-side MOSFET.
This capacitor is charged from V DD through the internal
bootstrap diode when the low-side MOSFET is on. The
bootstrap capacitor value should be selected carefully
to avoid oscillations during turn-on and turn-off at the
DH output. Choose a capacitor value approximately 20
times greater than the total gate capacitance of the
MOSFET being switched. Use a low-ESR, X7R-type
dielectric ceramic capacitor (typically a 0.1μF ceramic
is adequate). The high-side MOSFET’s continuous on-
time is limited due to the charge loss from the high-side
driver’s quiescent current. The maximum on-time is
dependent on the size of C BST , I BST (190μA max), and
V BST_UVLO. Note that the bootstrap capacitor requires
time to charge up to V DD , according to the time con-
stant of the charging loop through the lower MOSFET
(see the Typical Operating Circuit ). Ensure that the
lower MOSFET is on for at least the minimum time
required to charge C BST .
Driver Logic Inputs (IN_H, IN_L)
The MAX15018_ are CMOS (V DD /2) logic-input drivers,
and the MAX15019_ are TTL-compatible logic-input dri-
vers. The required logic-input levels are independent of
V DD . For example, the IC can be powered by a 10V sup-
ply while the logic inputs are provided from 12V CMOS
logic. Additionally, the logic inputs are protected against
voltage spikes up to 15V, regardless of V DD voltage. The
TTL and CMOS logic inputs have 400mV and 1.6V hys-
teresis, respectively, to avoid double pulsing during sig-
nal transition. The logic inputs are high-impedance pins
(500k ? typ) and should not be left unconnected to
ensure the input logic state is at a known level. With the
logic inputs unconnected, the DH and DL outputs pull
low as V DD rises up above the UVLO threshold. The
PWM output from the controller must assume a proper
state while powering up the device.
Applications Information
Supply Bypassing and Grounding
Careful attention is required when choosing the bypass-
ing and grounding scheme of the MAX15018_/
MAX15019_. Peak supply and output currents may
exceed 6A when both drivers are simultaneously driving
large external capacitive loads in phase. Supply drops
and ground shifts create forms of negative feedback for
inverterting topologies and may degrade the delay and
transition times. Ground shifts due to insufficient device
grounding may also disturb other circuits sharing the
same AC ground return path. Any series inductance in
the V DD , DH, DL, and/or GND paths can cause oscilla-
tions due to the very high di/dt when switching the
MAX15018_/MAX15019_ with any capacitive load. Place
one or more 0.1μF ceramic capacitors in parallel from
V DD to GND as close as possible to the device to
bypass the input supply. Use a ground plane to minimize
ground return resistance and series inductance. Place
the external MOSFETs as close as possible to the
MAX15018_/MAX15019_ to reduce trace length and fur-
ther minimize board inductance and AC path resistance.
Power Dissipation
Power dissipation in the MAX15018_/MAX15019_ is pri-
marily due to power loss in the internal boost diode and
the internal nMOS and pMOS FETS. For capacitive
loads, the total power dissipation for the device is:
P D = (C L x V DD 2 x f SW ) + (I VDDO + I BSTO ) x V DD
where C L is the combined capacitive load at DH and
DL, V DD is the supply voltage, and f SW is the switching
frequency of the IC. P D includes the power dissipated in
the internal bootstrap diode (P DIODE ). The internal
power dissipation reduces by P DIODE , if an external
bootstrap Schottky diode is used. The power dissipation
in the internal boost diode (when driving a capacitive
load) will be the charge through the diode per switching
period multiplied by the maximum diode forward voltage
drop (V F = 1V) as given in the following equation.
P DIODE = C DH x (V DD - 1) x f SW x V F
where C DH is the capacitive load at DH, V DD is the sup-
ply voltage, f SW is the switching frequency of the con-
verter, V F is the maximum diode forward voltage drop.
The total power dissipation when using the internal
boost diode will be P D and, when using an external
Schottky diode, will be P D - P DIODE . The total power
dissipated in the device must be kept below the maxi-
mum of 1.95W for the 8-pin SO with exposed pad at T A
= +70°C ambient.
10
______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| MAX15022EVKIT+ | KIT EVAL FOR MAX15022 |
| MAX15025EATB+T | IC GATE DRVR 2CH 16NS 10TDFN-EP |
| MAX15053EVKIT+ | BOARD EVAL FOR MAX15053 |
| MAX15054AUT+T | IC MOSFET DVR HIGH SIDE SOT-23-6 |
| MAX15070BEUT+T | IC MOSFET DRIVER HNM LL SOT23-6 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX15018BASA+ | 功能描述:功率驱动器IC 125V/3A High-Speed Half-B MOSFET Drvr RoHS:否 制造商:Micrel 产品:MOSFET Gate Drivers 类型:Low Cost High or Low Side MOSFET Driver 上升时间: 下降时间: 电源电压-最大:30 V 电源电压-最小:2.75 V 电源电流: 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube |
| MAX15018BASA+T | 功能描述:功率驱动器IC 125V/3A High-Speed Half-B MOSFET Drvr RoHS:否 制造商:Micrel 产品:MOSFET Gate Drivers 类型:Low Cost High or Low Side MOSFET Driver 上升时间: 下降时间: 电源电压-最大:30 V 电源电压-最小:2.75 V 电源电流: 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube |
| MAX15019AASA+ | 功能描述:功率驱动器IC 125V/3A High-Speed Half-B MOSFET Drvr RoHS:否 制造商:Micrel 产品:MOSFET Gate Drivers 类型:Low Cost High or Low Side MOSFET Driver 上升时间: 下降时间: 电源电压-最大:30 V 电源电压-最小:2.75 V 电源电流: 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube |
| MAX15019AASA+T | 功能描述:功率驱动器IC 125V/3A High-Speed Half-B MOSFET Drvr RoHS:否 制造商:Micrel 产品:MOSFET Gate Drivers 类型:Low Cost High or Low Side MOSFET Driver 上升时间: 下降时间: 电源电压-最大:30 V 电源电压-最小:2.75 V 电源电流: 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube |
| MAX15019BASA+ | 功能描述:功率驱动器IC 125V/3A High-Speed Half-B MOSFET Drvr RoHS:否 制造商:Micrel 产品:MOSFET Gate Drivers 类型:Low Cost High or Low Side MOSFET Driver 上升时间: 下降时间: 电源电压-最大:30 V 电源电压-最小:2.75 V 电源电流: 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。