- 您现在的位置：买卖IC网 > PDF目录1836 > MAX15035ETL+T (Maxim Integrated Products)IC REG BOOST SYNC 15A 40TQFN PDF资料下载
参数资料
| 型号： | MAX15035ETL+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 15/27页 |
| 文件大小： | 0K |
| 描述： | IC REG BOOST SYNC 15A 40TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 类型： | 升压（升压） |
| 输出类型： | 固定 |
| 输出数： | 1 |
| 输出电压： | 1.05V，1.5V |
| 输入电压： | 4.5 V ~ 26 V |
| PWM 型： | 电流模式 |
| 电流 - 输出： | 15A |
| 同步整流器： | 是 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 40-WFQFN 裸露焊盘 |
| 包装： | 带卷 (TR) |
| 供应商设备封装： | 40-TQFN-EP（6x6） |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页当前第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页
15A Step-Down Regulator with Internal Switches
V FB FB
t START = =
V FB FB
t SHDN = =
Power-on reset (POR) occurs when V CC rises above
approximately 3V, resetting the fault latch and prepar-
ing the controller for operation. The V CC UVLO circuitry
inhibits switching until V CC rises above 4.25V. The con-
troller powers up the reference once the system
enables the controller, V CC exceeds 4.25V, and EN is
driven high. With the reference in regulation, the con-
troller ramps the output voltage to the target REFIN volt-
age with a 1.2mV/μs slew rate:
V
1 . 2 mV μ s 1 . 2 V ms
The soft-start circuitry does not use a variable current
limit, so full output current is available immediately.
PGOOD becomes high impedance approximately
200μs after the target REFIN voltage has been reached.
The MAX15035 automatically uses pulse-skipping mode
during soft-start and uses forced-PWM mode during
soft-shutdown, regardless of the SKIP configuration.
For automatic startup, the input voltage should be pre-
sent before V CC . If the controller attempts to bring the
output into regulation without the input voltage present,
the fault latch trips. The controller remains shut down
until the fault latch is cleared by toggling EN or cycling
the V CC power supply below 0.5V.
If the V CC voltage drops below 4.25V, the controller
assumes that there is not enough supply voltage to
make valid decisions. To protect the output from over-
voltage faults, the controller shuts down immediately
and forces a high impedance on LX.
Shutdown
When the system pulls EN low, the MAX15035 enters
low-power shutdown mode. PGOOD is pulled low
immediately, and the output voltage ramps down with a
1.2mV/μs slew rate:
V
1 . 2 mV μ s 1 . 2 V ms
Slowly discharging the output capacitors by slewing
the output over a long period of time (typically 0.5ms to
2ms) keeps the average negative inductor current low
(damped response), thereby preventing the negative
output-voltage excursion that occurs when the con-
troller discharges the output quickly by permanently
turning on the low-side MOSFET (underdamped
When a fault condition—output UVP or thermal shut-
down—activates the shutdown sequence, the protection
circuitry sets the fault latch to prevent the controller from
restarting. To clear the fault latch and reactivate the
controller, toggle EN or cycle V CC power below 0.5V.
The MAX15035 automatically uses pulse-skipping mode
during soft-start and uses forced-PWM mode during
soft-shutdown, regardless of the SKIP configuration.
Modes of Operation
Ultrasonic Mode ( S K I P = Open = 3.3V)
Leaving SKIP unconnected activates a unique pulse-
skipping mode with a minimum switching frequency of
18kHz. This ultrasonic pulse-skipping mode eliminates
audio-frequency modulation that would otherwise be
present when a lightly loaded controller automatically
skips pulses. In ultrasonic mode, the controller automati-
cally transitions to fixed-frequency PWM operation when
the load reaches the same critical conduction point
(I LOAD(SKIP) ) that occurs when normally pulse skipping.
An ultrasonic pulse occurs when the controller detects
that no switching has occurred within the last 33μs.
Once triggered, the ultrasonic controller turns on the
low-side MOSFET to induce a negative inductor current
(Figure 3). After the inductor current reaches the nega-
tive ultrasonic current threshold, the controller turns off
the low-side MOSFET and triggers a constant on-time.
33 μ s (typ)
INDUCTOR
CURRENT
ZERO-CROSSING
DETECTION
0
response). This eliminates the need for the Schottky
diode normally connected between the output and
ground to clamp the negative output-voltage excursion.
After the controller reaches the zero target, the
MAX15035 shuts down completely—the drivers are dis-
abled (high impedance on LX)—the reference turns off,
and the supply currents drop to about 0.1μA (typ).
I SONIC
Figure 3. Ultrasonic Waveform
ON-TIME (t ON )
______________________________________________________________________________________
15
相关PDF资料 |
PDF描述 |
|---|---|
| MAX15037ATE+ | IC REG BUCK BST SYNC ADJ 16TQFN |
| MAX15038ETG+T | IC REG BUCK SYNC ADJ 4A 24TQFN |
| MAX15039ETG+T | IC REG BUCK SYNC ADJ 6A 24TQFN |
| MAX15041ETE+T | IC REG BUCK SYNC ADJ 3A 16TQFN |
| MAX15046AAEE+T | IC REG CTRLR BUCK PWM VM 16-QSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX15035EVKIT+ | 功能描述:电源管理IC开发工具 MAX15035 Eval Kit RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| MAX15036ATE/V+ | 功能描述:直流/直流开关转换器 2.2MHz 3A Buck wInt High-Side Switch RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| MAX15036ATE/V+T | 功能描述:直流/直流开关转换器 2.2MHz 3A Buck wInt High-Side Switch RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| MAX15036ATE+ | 功能描述:直流/直流开关转换器 2.2MHz 3A Buck wInt High-Side Switch RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| MAX15036ATE+T | 功能描述:直流/直流开关转换器 2.2MHz 3A Buck wInt High-Side Switch RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
发布紧急采购，3分钟左右您将得到回复。