- 您现在的位置：买卖IC网 > PDF目录1836 > MAX15035ETL+T (Maxim Integrated Products)IC REG BOOST SYNC 15A 40TQFN PDF资料下载
参数资料
| 型号： | MAX15035ETL+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 16/27页 |
| 文件大小： | 0K |
| 描述： | IC REG BOOST SYNC 15A 40TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 类型： | 升压（升压） |
| 输出类型： | 固定 |
| 输出数： | 1 |
| 输出电压： | 1.05V，1.5V |
| 输入电压： | 4.5 V ~ 26 V |
| PWM 型： | 电流模式 |
| 电流 - 输出： | 15A |
| 同步整流器： | 是 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 40-WFQFN 裸露焊盘 |
| 包装： | 带卷 (TR) |
| 供应商设备封装： | 40-TQFN-EP（6x6） |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页当前第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页
15A Step-Down Regulator with Internal Switches
When the on-time expires, the controller re-enables the
low-side MOSFET until the controller detects that the
inductor current drops below the zero-crossing thresh-
old. Starting with a negative inductor current pulse
greatly reduces the peak output voltage when com-
pared to starting with a positive inductor current pulse.
The output voltage at the beginning of the ultrasonic
pulse determines the negative ultrasonic current
threshold, resulting in the following equation:
V ISONIC = I L × 0 . 006 = ( V REFIN ? V FB ) × 0 . 7
where V FB > V REFIN .
Forced-PWM Mode ( S K I P = V DD )
The low-noise, forced-PWM mode ( SKIP = V DD ) dis-
ables the zero-crossing comparator, which controls the
low-side switch on-time. This forces the low-side gate-
drive waveform to constantly be the complement of the
high-side gate-drive waveform, so the inductor current
reverses at light loads while LX maintains a duty factor
of V OUT /V IN . The benefit of forced-PWM mode is to
keep the switching frequency fairly constant. However,
forced-PWM operation comes at a cost: the no-load 5V
bias current remains between 10mA to 50mA, depend-
ing on the switching frequency.
Automatic Pulse-Skipping Mode ( S K I P = GND or REF)
In skip mode ( SKIP = GND or 3.3V), an inherent auto-
matic switchover to PFM takes place at light loads. This
switchover is affected by a comparator that truncates
the low-side switch on-time at the inductor current’s
zero crossing. The zero-crossing comparator threshold
is set by the differential across LX to PGND.
DC output-accuracy specifications refer to the threshold
of the error comparator. When the inductor is in continu-
ous conduction, the MAX15035 regulates the valley of
the output ripple, so the actual DC output voltage is
higher than the trip level by 50% of the output ripple
voltage. In discontinuous conduction ( SKIP = GND and
I OUT < I LOAD(SKIP) ), the output voltage has a DC regu-
lation level higher than the error-comparator threshold
by approximately 1.5% due to slope compensation.
When SKIP is pulled to GND, the MAX15035 remains in
pulse-skipping mode. Since the output is not able to
sink current, the timing for negative dynamic output-volt-
age transitions depends on the load current and output
capacitance. Letting the output voltage drift down is
typically recommended to reduce the potential for audi-
ble noise since this eliminates the input current surge
during negative output-voltage transitions. See Figures
4 and 5.
The MAX15035 automatically always uses forced-PWM
operation during shutdown, regardless of the SKIP
configuration.
DYNAMIC REFIN WINDOW
REFIN
ACTUAL V OUT
OUTPUT
VOLTAGE
INTERNAL
PWM CONTROL
LX
INTERNAL TARGET
SKIP
NO PULSES: V OUT > V TARGET
PGOOD
OVP
DYNAMIC TRANSITION WHEN SKIP# = GND
Figure 4. Dynamic Transition when SKIP = GND
BLANK HIGH-Z
SET TO REF + 300mV
BLANK HIGH-Z
EA TARGET + 300mV
16
______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| MAX15037ATE+ | IC REG BUCK BST SYNC ADJ 16TQFN |
| MAX15038ETG+T | IC REG BUCK SYNC ADJ 4A 24TQFN |
| MAX15039ETG+T | IC REG BUCK SYNC ADJ 6A 24TQFN |
| MAX15041ETE+T | IC REG BUCK SYNC ADJ 3A 16TQFN |
| MAX15046AAEE+T | IC REG CTRLR BUCK PWM VM 16-QSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX15035EVKIT+ | 功能描述:电源管理IC开发工具 MAX15035 Eval Kit RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| MAX15036ATE/V+ | 功能描述:直流/直流开关转换器 2.2MHz 3A Buck wInt High-Side Switch RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| MAX15036ATE/V+T | 功能描述:直流/直流开关转换器 2.2MHz 3A Buck wInt High-Side Switch RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| MAX15036ATE+ | 功能描述:直流/直流开关转换器 2.2MHz 3A Buck wInt High-Side Switch RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| MAX15036ATE+T | 功能描述:直流/直流开关转换器 2.2MHz 3A Buck wInt High-Side Switch RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
发布紧急采购，3分钟左右您将得到回复。