- 您现在的位置：买卖IC网 > PDF目录1836 > MAX15035ETL+T (Maxim Integrated Products)IC REG BOOST SYNC 15A 40TQFN PDF资料下载
参数资料
| 型号： | MAX15035ETL+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 24/27页 |
| 文件大小： | 0K |
| 描述： | IC REG BOOST SYNC 15A 40TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 类型： | 升压（升压） |
| 输出类型： | 固定 |
| 输出数： | 1 |
| 输出电压： | 1.05V，1.5V |
| 输入电压： | 4.5 V ~ 26 V |
| PWM 型： | 电流模式 |
| 电流 - 输出： | 15A |
| 同步整流器： | 是 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 40-WFQFN 裸露焊盘 |
| 包装： | 带卷 (TR) |
| 供应商设备封装： | 40-TQFN-EP（6x6） |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页当前第24页第25页第26页第27页
15A Step-Down Regulator with Internal Switches
? V
+ V
(
)
? ?
? ? 1 ? h × t OFF ( MIN ) f SW
I RMS = ? LOAD ? V OUT ( V IN ? V OUT )
When only using ceramic output capacitors, output
overshoot (V SOAR ) typically determines the minimum
output capacitance requirement. Their relatively low
capacitance value may allow significant output over-
shoot when stepping from full-load to no-load condi-
tions, unless designed with a small inductance value
and high switching frequency to minimize the energy
transferred from the inductor to the capacitor during
load-step recovery.
Unstable operation manifests itself in two related but
distinctly different ways: double pulsing and feedback-
loop instability. Double pulsing occurs due to noise on
the output or because the ESR is so low that there is
not enough voltage ramp in the output voltage signal.
This “fools” the error comparator into triggering a new
cycle immediately after the minimum off-time period
has expired. Double pulsing is more annoying than
harmful, resulting in nothing worse than increased out-
put ripple. However, it can indicate the possible pres-
ence of loop instability due to insufficient ESR. Loop
instability can result in oscillations at the output after
line or load steps. Such perturbations are usually
damped, but can cause the output voltage to rise
above or fall below the tolerance limits.
The easiest method for checking stability is to apply a
very fast zero-to-max load transient and carefully
observe the output voltage-ripple envelope for over-
shoot and ringing. It can help to simultaneously monitor
the inductor current with an AC current probe. Do not
allow more than one cycle of ringing after the initial
step-response under/overshoot.
Input Capacitor Selection
The input capacitor must meet the ripple current
requirement (I RMS ) imposed by the switching currents.
The I RMS requirements may be determined by the fol-
lowing equation:
? I ?
? V IN ?
The worst-case RMS current requirement occurs when
operating with V IN = 2V OUT . At this point, the above
equation simplifies to I RMS = 0.5 x I LOAD .
For most applications, nontantalum chemistries (ceramic,
aluminum, or OS-CON) are preferred due to their resis-
tance to inrush surge currents typical of systems with a
mechanical switch or connector in series with the input.
If the Quick-PWM controller is operated as the second
stage of a two-stage power-conversion system, tanta-
lum input capacitors are acceptable. In either configu-
ration, choose an input capacitor that exhibits less than
+10°C temperature rise at the RMS input current for
optimal circuit longevity.
Minimum Input-Voltage Requirements
and Dropout Performance
The output voltage-adjustable range for continuous-
conduction operation is restricted by the nonadjustable
minimum off-time one-shot. For best dropout perfor-
mance, use the slower (200kHz) on-time settings. When
working with low-input voltages, the duty-factor limit
must be calculated using worst-case values for on- and
off-times. Manufacturing tolerances and internal propa-
gation delays introduce an error to the on-times. This
error is greater at higher frequencies. Also, keep in
mind that transient response performance of buck reg-
ulators operated too close to dropout is poor, and bulk
output capacitance must often be added (see the V SAG
equation in the Quick-PWM Design Procedure section).
The absolute point of dropout is when the inductor cur-
rent ramps down during the minimum off-time ( Δ I DOWN )
as much as it ramps up during the on-time ( Δ I UP ). The
ratio h = Δ I UP / Δ I DOWN is an indicator of the ability to
slew the inductor current higher in response to
increased load, and must always be greater than 1. As
h approaches 1, the absolute minimum dropout point,
the inductor current cannot increase as much during
each switching cycle and V SAG greatly increases
unless additional output capacitance is used.
A reasonable minimum value for h is 1.5, but adjusting
this up or down allows trade-offs between V SAG , output
capacitance, and minimum operating voltage. For a
given value of h, the minimum operating voltage can be
calculated as:
? V ?
V IN ( MIN ) = ? OUT DROOP CHG ?
where V DROOP is the voltage-positioning droop, V CHG is
the parasitic voltage drop in the charge path, and
t OFF(MIN) is from the Electrical Characteristics table. The
absolute minimum input voltage is calculated with h = 1.
If the calculated V IN(MIN) is greater than the required min-
imum input voltage, reduce the operating frequency or
add output capacitance to obtain an acceptable V SAG . If
operation near dropout is anticipated, calculate V SAG to
be sure of adequate transient response.
Dropout design example:
V OUT = 3.3V
f SW = 300kHz
t OFF(MIN) = 350ns
V DROOP = 0V
V CHG = 150mV (10A load)
h = 1.5
24
______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| MAX15037ATE+ | IC REG BUCK BST SYNC ADJ 16TQFN |
| MAX15038ETG+T | IC REG BUCK SYNC ADJ 4A 24TQFN |
| MAX15039ETG+T | IC REG BUCK SYNC ADJ 6A 24TQFN |
| MAX15041ETE+T | IC REG BUCK SYNC ADJ 3A 16TQFN |
| MAX15046AAEE+T | IC REG CTRLR BUCK PWM VM 16-QSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX15035EVKIT+ | 功能描述:电源管理IC开发工具 MAX15035 Eval Kit RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| MAX15036ATE/V+ | 功能描述:直流/直流开关转换器 2.2MHz 3A Buck wInt High-Side Switch RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| MAX15036ATE/V+T | 功能描述:直流/直流开关转换器 2.2MHz 3A Buck wInt High-Side Switch RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| MAX15036ATE+ | 功能描述:直流/直流开关转换器 2.2MHz 3A Buck wInt High-Side Switch RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| MAX15036ATE+T | 功能描述:直流/直流开关转换器 2.2MHz 3A Buck wInt High-Side Switch RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
发布紧急采购，3分钟左右您将得到回复。