- 您现在的位置：买卖IC网 > PDF目录16702 > MAX1533AETJ+T (Maxim Integrated Products)IC POWER SUPPLY CONTROLER 32TQFN PDF资料下载
参数资料
| 型号： | MAX1533AETJ+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 22/38页 |
| 文件大小： | 0K |
| 描述： | IC POWER SUPPLY CONTROLER 32TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 应用： | 电源控制器 |
| 输入电压： | 4.5 V ~ 26 V |
| 电流 - 电源： | 15µA |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-WFQFN 裸露焊盘 |
| 供应商设备封装： | 32-TQFN-EP（5x5） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页当前第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页
High-Efficiency, 5x Output, Main Power-Supply
Controllers for Notebook Computers
Frequency Selection (FSEL)
The FSEL input selects the PWM-mode switching fre-
quency. Table 4 shows the switching frequency based
on FSEL connection. High-frequency (500kHz) operation
optimizes the application for the smallest component
size, trading off efficiency due to higher switching losses.
This may be acceptable in ultra-portable devices where
the load currents are lower. Low-frequency (200kHz)
operation offers the best overall efficiency at the expense
of component size and board space.
Forced-PWM Mode
The low-noise forced-PWM mode disables the zero-
crossing comparator, which controls the low-side switch
on-time. This forces the low-side gate-drive waveform to
constantly be the complement of the high-side gate-
drive waveform, so the inductor current reverses at light
loads while DH_ maintains a duty factor of V OUT /V IN . The
benefit of forced-PWM mode is to keep the switching fre-
quency fairly constant. However, forced-PWM operation
comes at a cost: the no-load 5V supply current remains
between 15mA and 50mA, depending on the external
MOSFETs and switching frequency.
Forced-PWM mode is most useful for avoiding audio-
frequency noise and improving load-transient
response. Since forced-PWM operation disables the
zero-crossing comparator, the inductor current revers-
es under light loads.
Light-Load Operation Control ( SKIP )
The MAX1533A/MAX1537A include a light-load operat-
ing-mode control input ( SKIP ) used to independently
enable or disable the zero-crossing comparator for
Idle-Mode Current-Sense Threshold
The on-time of the step-down controller terminates
when the output voltage exceeds the feedback thresh-
old and when the current-sense voltage exceeds the
idle-mode current-sense threshold. Under light-load
conditions, the on-time duration depends solely on the
idle-mode current-sense threshold, which is approxi-
mately 20% of the full-load current-limit threshold set by
ILIM_. This forces the controller to source a minimum
amount of power with each cycle. To avoid overcharg-
ing the output, another on-time cannot begin until the
output voltage drops below the feedback threshold.
Since the zero-crossing comparator prevents the
switching regulator from sinking current, the controller
must skip pulses. Therefore, the controller regulates the
valley of the output ripple under light-load conditions.
Automatic Pulse-Skipping Crossover
In skip mode, an inherent automatic switchover to PFM
takes place at light loads (Figure 4). This switchover is
affected by a comparator that truncates the low-side
switch on-time at the inductor current’s zero crossing.
The zero-crossing comparator senses the inductor cur-
rent across the low-side MOSFET (PGND to LX_). Once
V PGND - V LX _ drops below the 3mV zero-crossing cur-
rent-sense threshold, the comparator forces DL_ low
(Figure 3). This mechanism causes the threshold
between pulse-skipping PFM and nonskipping PWM
operation to coincide with the boundary between con-
tinuous and discontinuous inductor-current operation
(also known as the “critical conduction” point). The
load-current level at which PFM/PWM crossover
occurs, I LOAD(SKIP) , is given by:
both controllers. When the zero-crossing comparator is
enabled, the controller forces DL_ low when the cur-
rent-sense inputs detect zero inductor current. This
keeps the inductor from discharging the output capaci-
I LOAD ( SKIP ) =
V OUT (V IN ? V OUT )
2 × V IN × f SW × L
tors and forces the controller to skip pulses under light-
load conditions to avoid overcharging the output. When
the zero-crossing comparator is disabled, the controller
is forced to maintain PWM operation under light-load
conditions (forced-PWM).
Table 4. FSEL Configuration Table
The switching waveforms may appear noisy and asyn-
chronous when light loading causes pulse-skipping
operation, but this is a normal operating condition that
results in high light-load efficiency. Trade-offs in PFM
noise vs. light-load efficiency are made by varying the
inductor value. Generally, low inductor values produce
a broader efficiency vs. load curve, while higher values
result in higher full-load efficiency (assuming that the
FSEL
V CC
REF
GND
SWITCHING FREQUENCY
500kHz
300kHz
200kHz
coil resistance remains fixed) and less output voltage
ripple. Penalties for using higher inductor values
include larger physical size and degraded load-tran-
sient response (especially at low input-voltage levels).
22
______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| REC5-2409DRW/H6/C | CONV DC/DC 5W 18-36VIN +/-09VOUT |
| V375C36T75BL3 | CONVERTER MOD DC/DC 36V 75W |
| RBM24DSXS | CONN EDGECARD 48POS DIP .156 SLD |
| GBM18DRST | CONN EDGECARD 36POS DIP .156 SLD |
| V72C15E150BL3 | CONVERTER MOD DC/DC 15V 150W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX1533ETJ | 功能描述:电流和电力监控器、调节器 RoHS:否 制造商:STMicroelectronics 产品:Current Regulators 电源电压-最大:48 V 电源电压-最小:5.5 V 工作温度范围:- 40 C to + 150 C 安装风格:SMD/SMT 封装 / 箱体:HPSO-8 封装:Reel |
| MAX1533ETJ+ | 功能描述:电流和电力监控器、调节器 PS Controllers for for Notebooks RoHS:否 制造商:STMicroelectronics 产品:Current Regulators 电源电压-最大:48 V 电源电压-最小:5.5 V 工作温度范围:- 40 C to + 150 C 安装风格:SMD/SMT 封装 / 箱体:HPSO-8 封装:Reel |
| MAX1533ETJ+T | 功能描述:电流和电力监控器、调节器 PS Controllers for for Notebooks RoHS:否 制造商:STMicroelectronics 产品:Current Regulators 电源电压-最大:48 V 电源电压-最小:5.5 V 工作温度范围:- 40 C to + 150 C 安装风格:SMD/SMT 封装 / 箱体:HPSO-8 封装:Reel |
| MAX1533ETJ-T | 功能描述:电流和电力监控器、调节器 RoHS:否 制造商:STMicroelectronics 产品:Current Regulators 电源电压-最大:48 V 电源电压-最小:5.5 V 工作温度范围:- 40 C to + 150 C 安装风格:SMD/SMT 封装 / 箱体:HPSO-8 封装:Reel |
| MAX1533EVKIT | 功能描述:电流和电力监控器、调节器 Evaluation Kit for the MAX1533 RoHS:否 制造商:STMicroelectronics 产品:Current Regulators 电源电压-最大:48 V 电源电压-最小:5.5 V 工作温度范围:- 40 C to + 150 C 安装风格:SMD/SMT 封装 / 箱体:HPSO-8 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。