- 您现在的位置：买卖IC网 > PDF目录1837 > MAX1544ETL+ (Maxim Integrated Products)IC QUICK-PWM DUAL-PHASE 40-TQFN PDF资料下载
参数资料
| 型号： | MAX1544ETL+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 30/42页 |
| 文件大小： | 0K |
| 描述： | IC QUICK-PWM DUAL-PHASE 40-TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 50 |
| 系列： | Quick-PWM™ |
| 应用： | 控制器，AMD Hammer |
| 输入电压： | 2 V ~ 28 V |
| 输出数： | 1 |
| 输出电压： | 0.68 V ~ 1.55 V |
| 工作温度： | -40°C ~ 100°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 40-WFQFN 裸露焊盘 |
| 供应商设备封装： | 40-TQFN-EP（6x6） |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页当前第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页
Dual-Phase, Quick-PWM Controller for
AMD Hammer CPU Core Power Supplies
V GS ( TH ) < V IN ? RSS ?
Since only the valley current is actively limited, the
actual peak current is greater than the current-limit
threshold by an amount equal to the inductor ripple
current. Therefore, the exact current-limit characteristic
and maximum load capability are a function of the
current-sense resistance, inductor value, and battery
voltage. When combined with the undervoltage protec-
tion circuit, this current-limit method is effective in
almost every circumstance.
There is also a negative current limit that prevents
excessive reverse inductor currents when V OUT is
sinking current. The negative current-limit threshold is
set to approximately 120% of the positive current limit,
and therefore tracks the positive current limit when ILIM
is adjusted. When a phase drops below the negative
current limit, the controller immediately activates an on-
time pulse — DL turns off, and DH turns on — allowing
the inductor current to remain above the negative cur-
rent threshold.
The current-limit threshold is adjusted with an external
resistive voltage-divider at ILIM. The current-limit
threshold voltage adjustment range is from 10mV to
75mV. In the adjustable mode, the current-limit thresh-
old voltage is precisely 1/20 the voltage seen at ILIM.
The threshold defaults to 30mV when ILIM is connected
to V CC . The logic threshold for switchover to the 30mV
default value is approximately V CC - 1V.
Carefully observe the PC board layout guidelines to
ensure that noise and DC errors do not corrupt the cur-
rent-sense signals seen by the current-sense inputs
(C_P, C_N).
MOSFET Gate Drivers (DH, DL)
The DH and DL drivers are optimized for driving mod-
pling from the drain to the gate of the low-side
MOSFETs when LX switches from ground to V IN .
Applications with high input voltages and long, induc-
tive DL traces may require additional gate-to-source
capacitance to ensure fast-rising LX edges do not pull
up the low-side MOSFET ’ s gate voltage, causing shoot-
through currents. The capacitive coupling between LX
and DL created by the MOSFET ’ s gate-to-drain capaci-
tance (C RSS ), gate-to-source capacitance (C ISS -
C RSS ), and additional board parasitics should not
exceed the minimum threshold voltage:
? C ?
? C ISS ?
Lot-to-lot variation of the threshold voltage can cause
problems in marginal designs. Typically, adding
4700pF between DL and power ground (C NL in
Figure 9), close to the low-side MOSFETs, greatly
reduces coupling. Do not exceed 22nF of total gate
capacitance to prevent excessive turn-off delays.
Alternatively, shoot-through currents may be caused by
a combination of fast high-side MOSFETs and slow low-
side MOSFETs. If the turn-off delay time of the low-side
MOSFET is too long, the high-side MOSFETs can turn
on before the low-side MOSFETs have actually turned
off. Adding a resistor less than 5 ? in series with BST
slows down the high-side MOSFET turn-on time, elimi-
nating the shoot-through currents without degrading
the turn-off time (R BST in Figure 9). Slowing down the
high-side MOSFET also reduces the LX node rise time,
thereby reducing EMI and high-frequency coupling
responsible for switching noise.
erately sized, high-side and larger, low-side power
MOSFETs. This is consistent with the low-duty factor
seen in the notebook CPU environment, where a large
V IN - V OUT differential exists. An adaptive dead-time
circuit monitors the DL output and prevents the high-
V DD
BST
(R BST )*
C BYP
D BST
INPUT
side FET from turning on until DL is fully off. There must
be a low-resistance, low-inductance path from the DL
driver to the MOSFET gate in order for the adaptive
dead-time circuit to work properly. Otherwise, the
DH
LX
C BST
N H
(V IN )
L
sense circuitry in the Quick-PWM controller interprets
V DD
the MOSFET gate as “ off ” while there is actually charge
still left on the gate. Use very short, wide traces (50 mils
to 100 mils wide if the MOSFET is 1in from the device).
The dead time at the other edge (DH turning off) is
determined by a fixed 35ns internal delay.
DL
PGND
(C NL )*
N L
The internal pulldown transistor that drives DL low is
robust, with a 0.4 ? (typ) on-resistance. This helps pre-
vent DL from being pulled up due to capacitive cou-
(R BST )* OPTIONAL — THE RESISTOR LOWERS EMI BY DECREASING THE SWITCHING
NODE RISE TIME.
(CNL)* OPTIONAL — THE CAPACITOR REDUCES LX TO DL CAPACITIVE COUPLING THAT
CAN CAUSE SHOOT-THROUGH CURRENTS.
Figure 9. Optional Gate-Driver Circuitry
30
______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| MAX1545ETL+ | IC QUICK-PWM DUAL-PHASE 40-TQFN |
| MAX1551EZK+T | IC BATT CHRGR LI+ 1CELL SOT23-5 |
| MAX1556ETB/V+T | IC REG BUCK SYNC ADJ 1.2A 10TDFN |
| MAX1565ETJ+ | IC DGTL CAM PWR-SUP 5CH 32TQFN |
| MAX1567ETL+ | IC DGTL CAM PWR-SUP 6CH 40TQFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX1544ETL+ | 功能描述:电压模式 PWM 控制器 Dual-Phase Quick-PWM Controller RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel |
| MAX1544ETL+T | 功能描述:电压模式 PWM 控制器 Dual-Phase Quick-PWM Controller RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel |
| MAX1544ETL+TG075 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
| MAX1544ETL-T | 功能描述:电压模式 PWM 控制器 RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel |
| MAX1544EVKIT | 制造商:Maxim Integrated Products 功能描述:DUAL-PHASE, QUICK-PWM CONTROLLER FOR AMD HAMM - Bulk |
发布紧急采购，3分钟左右您将得到回复。