- 您现在的位置：买卖IC网 > PDF目录17273 > MAX17030EVKIT+ (Maxim Integrated Products)EVALUATION KIT FOR MAX17030 PDF资料下载
参数资料
| 型号： | MAX17030EVKIT+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 31/39页 |
| 文件大小： | 0K |
| 描述： | EVALUATION KIT FOR MAX17030 |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 1 |
| 系列： | Quick-PWM™ |
| 主要目的： | DC/DC，步降 |
| 输出及类型： | 1，非隔离 |
| 输出电压： | 0 ~ 1.5 V |
| 输入电压： | 7 ~ 26 V |
| 稳压器拓扑结构： | 降压 |
| 板类型： | 完全填充 |
| 已供物品： | 板 |
| 已用 IC / 零件： | MAX17030 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页当前第31页第32页第33页第34页第35页第36页第37页第38页第39页
1/2/3-Phase Quick-PWM
IMVP-6.5 VID Controllers
t TRAN ( START ) =
t TRAN ( SHDN ) =
Power-on reset (POR) occurs when V CC rises above
approximately 2V, resetting the fault latch and prepar-
ing the controller for operation. The V CC UVLO circuitry
inhibits switching until V CC rises above 4.25V. The con-
troller powers up the reference once the system
enables the controller, V CC is above 4.25V, and SHDN
driven high. With the reference in regulation, the con-
troller ramps the output voltage to the boot voltage
(1.1V) at 1/4 the slew rate set by R TIME :
4 V BOOT
( dV TARGET dt )
where dV TARGET /dt = 12.5mV/μs x 71.5k Ω /R TIME is the
slew rate. The soft-start circuitry does not use a variable
current limit, so full output current is available immedi-
ately. CLKEN is pulled low approximately 60μs after the
MAX17030/MAX17036 reach the boot voltage. At the
same time, the MAX17030/MAX17036 slew the output
to the voltage set at the VID inputs at the programmed
slew rate. PWRGD becomes high impedance approxi-
mately 5ms after CLKEN is pulled low. The MAX17030/
MAX17036 automatically operate in pulse-skipping
mode during soft-start, and use forced-PWM operation
during soft-shutdown, regardless of the DPRSLPVR and
PSI configuration.
If the V CC voltage drops below 4.25V, the controller
assumes that there is not enough supply voltage to make
valid decisions, and shuts down immediately. DH and DL
are forced low, and CSN1 10 Ω discharge FET is
enabled.
Shutdown
When SHDN goes low, the MAX17030/MAX17036
enters low-power shutdown mode. PWRGD is pulled
low immediately, and the output voltage ramps down at
1/4 the slew rate set by R TIME :
4 V OUT
( dV TARGET dt )
where dV TARGET /dt = 12.5mV/μs x 71.5k Ω /R TIME is the
slew rate. After the output voltage drops to 12.5mV, the
MAX17030/MAX17036 shut down completely—the dri-
vers are disabled (DL1 and DL2 driven low, PWM3 is
three-state, and DRSKP low), the reference turns off,
10 Ω CSN1 discharge FET is turned on, and the supply
current drops below 1μA.
When an undervoltage fault condition activates the shut-
down sequence, the protection circuitry sets the fault
latch to prevent the controller from restarting. To clear
the fault latch and reactivate the controller, toggle SHDN
or cycle V CC power below 0.5V.
Current Monitor (IMON)
The MAX17030/MAX17036 include a unidirectional
transconductance amplifier that sources current pro-
portional to the positive current-sense voltage. The
IMON output current is defined by:
I IMON = G m(IMON) x Σ (V CSP - V CSN )
where G m(IMON) = 1.6mS (typ) and the IMON current is
unidirectional (sources current out of IMON only) for
positive current-sense values. For negative current-
sense voltages, the IMON current is zero.
Connect an external resistor between IMON and GNDS
to create the desired IMON gain based on the following
equation:
R IMON = 0.9V/(I MAX x R SENSE(MIN) x G m(IMON_MIN) )
where I MAX is defined in the Current Monitor section of
the Intel IMVP-6.5 specification and based on discrete
increments (10A, 20A, 30A, 40A, etc.), R SENSE(MIN) is
the minimum effective value of the current-sense ele-
ment (sense resistor or inductor DCR) that is used to
provide the current-sense voltage, and G m(IMON_MIN)
is the minimum transconductance amplifier gain as
defined in the Electrical Characteristics.
The IMON voltage is internally clamped to a maximum
of 1.1V (typ), preventing the IMON output from exceed-
ing the IMON voltage rating even under overload or
short-circuit conditions. When the controller is disabled,
IMON is pulled to ground.
The transconductance amplifier and voltage clamp are
internally compensated, so IMON cannot directly drive
large capacitance values. To filter the IMON signal, use
an RC filter as shown in Figure 1.
Temperature Comparator ( VRHOT )
The MAX17030/MAX17036 also feature an independent
comparator with an accurate threshold (V HOT ) that
tracks the analog supply voltage (V HOT = 0.3V CC ). This
makes the thermal trip threshold independent of the V CC
supply voltage tolerance. Use a resistor- and thermistor-
divider between V CC and GND to generate a voltage-
regulator overtemperature monitor. Place the thermistor
as close to the MOSFETs and inductors as possible.
Fault Protection (Latched)
Output Overvoltage Protection
The overvoltage-protection (OVP) circuit is designed to
protect the CPU against a shorted high-side MOSFET
by drawing high current and blowing the battery fuse.
The MAX17030/MAX17036 continuously monitor the
output for an overvoltage fault. An OVP fault is detected
if the output voltage exceeds the set VID DAC voltage
by more than 300mV, or the fixed 1.5V (typ) threshold
______________________________________________________________________________________
31
相关PDF资料 |
PDF描述 |
|---|---|
| RCC06DRAH | CONN EDGECARD 12POS R/A .100 SLD |
| RBC12DRXH | CONN EDGECARD 24POS DIP .100 SLD |
| RBC10DCSN | CONN EDGECARD 20POS DIP .100 SLD |
| RBC10DRTS | CONN EDGECARD 20POS DIP .100 SLD |
| RCC12DCMS | CONN EDGECARD 24POS .100 WW |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX17030EVKIT+ | 功能描述:电源管理IC开发工具 MAX17030 Eval Kit RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| MAX17030GTL+ | 功能描述:电压模式 PWM 控制器 1/2/3-Phase PWM IMVP-6.5 VID Ctlr RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel |
| MAX17030GTL+T | 功能描述:电压模式 PWM 控制器 1/2/3-Phase PWM IMVP-6.5 VID Ctlr RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel |
| MAX17031ETG+ | 功能描述:电压模式 PWM 控制器 Dual PWM Step-Down Controller RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel |
| MAX17031ETG+T | 功能描述:电压模式 PWM 控制器 Dual PWM Step-Down Controller RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。