- 您现在的位置：买卖IC网 > PDF目录21684 > MAX17410GTM+T (Maxim Integrated)IC CTLR QPWM 2PH FOR IMV 48TQFN PDF资料下载
参数资料
| 型号： | MAX17410GTM+T |
| 厂商： | Maxim Integrated |
| 文件页数： | 15/45页 |
| 文件大小： | 0K |
| 描述： | IC CTLR QPWM 2PH FOR IMV 48TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 系列： | * |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页当前第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页
Dual-Phase, Quick-PWM Controller
for IMVP6+ CPU Core Power Supplies
Pin Description
PIN
1
NAME
PWRGD
FUNCTION
Open-Drain Power-Good Output. After output voltage transitions, except during power-up and power-
down, if FB is in regulation, then PWRGD is high impedance. PWRGD is low during startup,
continues to be low while the output is at the boot voltage, and stays low until 5ms (typ) after
CLKENgoes low, after which it starts monitoring the FB voltage and goes high if FB is within the
PWRGD threshold window. PWRGD is forced low during soft-shutdown and while in shutdown.
PWRGD is forced high impedance whenever the slew-rate controller is active (output voltage
transitions), and continues to be forced high impedance for an additional 20 μs after the transition
is completed. The PWRGD upper threshold is blanked during any downward output voltage
transition that happens when the controller is in skip mode, and stays blanked until the slew-rate-
controlled internal-transition-related PWRGD blanking period is complete and the output reaches
regulation. A pullup resistor on PWRGD causes additional finite shutdown current.
Power-State Indicator. This low-voltage logic input indicates power usage and sets the operating
mode together with DPRSLPVR as shown in the truth table below. While DPRSLPVR is low, if PSI is
forced low, the controller is immediately set to 1-phase forced-PWM mode. The controller returns to
2-phase forced-PWM mode when PSI is forced high.
DPRSLPVR
1
1
PSI
0
1
Mode
Very low current (1-phase skip)
Low current (approx 3A) (1-phase skip)
2
PSI
0
0
0
1
Intermediate power potential (1-phase PWM)
Max power potential (full-phase PWM: 2-phase or 1-phase as set by user at
CSP2)
The controller is in 2-phase skip mode during startup, but is in 2-phase forced-PWM mode during
soft-shutdown, irrespective of the DPRSLPVR and PSI logic levels. The controller is also in 2-phase
skip mode while in boot mode, but is in 2-phase forced-PWM mode during the transition from boot
mode to VID mode, irrespective of the DPRSLPVR and PSI logic levels. However, if phase 2 is
disabled by connecting CSP2 to V CC , then only phase 1 is active in the above modes.
Power Monitor Output:
V(PWR) = K PWR x V(OUTS, GNDS) x V(CSPAVG, CSN)/V(TIME, ILIM)
where K PWR = 21.25 typical.
3
4
5
6
PMON
THRM
VRHOT
NTC
If ILIM is externally connected to a 5V rail to enable the internal default/preset current-limit
threshold, then the V(TIME, ILIM) value to be used in the above equation is 225mV.
Do not use the power monitor in any configuration that would cause its output V(PMON) to exceed
(V CC - 0.5V).
PMON is pulled to ground when the MAX17410 is in shutdown.
Resistive Input of Thermal Comparator. Connect a resistor to ground to set the VRHOT threshold.
THRM and NTC have matched 50 μA current sources, so the resistance value = the NTC
resistance at the desired high temperature. VRHOT is pulled low when the voltage at NTC goes
below the voltage at THRM.
Open-Drain Output of Internal Comparator. VRHOT is pulled low when the voltage at NTC goes
below the voltage at THRM. VRHOT is high impedance in shutdown.
Thermistor Input of Thermal Comparator. Connect a standard thermistor to ground. THRM and NTC
have matched 50 μA current sources, so the resistance value = the NTC resistance at the desired
high temperature. VRHOT is pulled low when the voltage at NTC goes below the voltage at THRM.
______________________________________________________________________________________
15
相关PDF资料 |
PDF描述 |
|---|---|
| BAV99W,115 | DIODE ARRAY 100V 130MA SOT323 |
| ATS049B | CRYSTAL 4.9152 MHZ 18PF |
| ATS221B | CRYSTAL 22.1184 MHZ 18 PF FUND |
| ATS20A | CRYSTAL 20.0 MHZ 20 PF FUND |
| ATS073B | CRYSTAL 7.3728 MHZ 18 PF FUND |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX17411GTM+ | 功能描述:电流型 PWM 控制器 IMVP7 CPU & Graphics Controller RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| MAX17411GTM+T | 功能描述:电流型 PWM 控制器 IMVP7 CPU & Graphics Controller RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| MAX17411RGTM+ | 功能描述:电流型 PWM 控制器 RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| MAX17411RGTM+T | 功能描述:电流型 PWM 控制器 RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| MAX17411RGTM+TW | 功能描述:电流型 PWM 控制器 RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
发布紧急采购，3分钟左右您将得到回复。