- 您现在的位置：买卖IC网 > PDF目录1839 > MAX17480GTL+T (Maxim Integrated Products)IC CTRLR SERIAL VID 40-TQFN PDF资料下载
参数资料
| 型号： | MAX17480GTL+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 30/48页 |
| 文件大小： | 0K |
| 描述： | IC CTRLR SERIAL VID 40-TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 应用： | 处理器 |
| 电流 - 电源： | 5mA |
| 电源电压： | 4.5 V ~ 5.5 V |
| 工作温度： | -40°C ~ 105°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 40-WFQFN 裸露焊盘 |
| 供应商设备封装： | 40-TQFN-EP（5x5） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页当前第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页
AMD 2-/3-Output Mobile Serial
VID Controller
V ( V ? V )
2 V IN SW L
depending on the external MOSFETs and switching fre-
quency. To maintain high efficiency under light load
conditions, the processor could switch the controller to a
low-power pulse-skipping control scheme.
Pulse-Skipping Operation
During soft-start and in power-saving mode—when the
PSI_L bit is set to 0—the MAX17480 operates in pulse-
skipping mode. Pulse-skipping mode enables the driver’s
zero-crossing comparator, so the driver pulls its DL low
when “zero” inductor current is detected (V GND - V LX =
0). This keeps the inductor from discharging the output
capacitors and forces the controller to skip pulses under
light load conditions to avoid overcharging the output.
In pulse-skipping operation, the controller terminates
the on-time when the output voltage exceeds the feed-
back threshold and when the current-sense voltage
exceeds the idle-mode current-sense threshold (V IDLE
= 0.15 x V LIMIT for the core SMPS and I LX3MIN = 0.25 x
I LX3PK setting for the NB SMPS). Under heavy load
conditions, the continuous inductor current remains
above the idle-mode current-sense threshold, so the
on-time depends only on the feedback voltage thresh-
old. Under light load conditions, the controller remains
above the feedback voltage threshold, so the on-time
duration depends solely on the idle-mode current-
sense threshold, which is approximately 15% of the full-
load peak current-limit threshold set by ILIM12 for the
core SMPSs and 25% of the full-load peak current-limit
threshold set by ILIM3 for the NB SMPS.
During downward VID transitions, the controller tem-
porarily sets the OVP threshold of the SMPSs to 1.85V
(typ), preventing false OVP faults. Once the error ampli-
fier detects that the output voltage is in regulation, the
OVP threshold tracks the selected VID DAC code.
Each SMPS can be individually set to operate in pulse-
skipping mode when its PSI_L bit is set to 0, or set to oper-
ate in forced-PWM mode when its PSI_L bit is set to 1.
When the core SMPSs are configured for combined-
mode operation, core supplies operate in 1-phase
pulse-skipping mode when PSI_L = 0, and core sup-
plies are in 2-phase forced-PWM mode when PSI_L = 1.
Idle-Mode Current-Sense Threshold
The idle-mode current-sense threshold forces a lightly
loaded SMPS to source a minimum amount of power
with each on-time since the controller cannot terminate
the on-time until the current-sense voltage exceeds the
idle-mode current-sense threshold (V IDLE = 0.15 x
V LIMIT for the core SMPS and I LX3MIN = 0.25 x I LX3PK
setting for the NB SMPS). Since the zero-crossing com-
parator prevents the switching SMPS from sinking
current, the controller must skip pulses to avoid over-
charging the output. When the clock edge occurs, if the
output voltage still exceeds the feedback threshold, the
controller does not initiate another on-time. This forces
the controller to actually regulate the valley of the out-
put voltage ripple under light load conditions.
Automatic Pulse-Skipping Crossover
In skip mode, the MAX17480 zero-crossing compara-
tors are active. Therefore, an inherent automatic
switchover to PFM takes place at light loads, resulting in
a highly efficient operating mode. This switchover is
affected by a comparator that truncates the low-side
switch on-time at the inductor current’s zero crossing.
The driver ’s zero-crossing comparator senses the
inductor current across the low-side MOSFET. Once
V GND - V LX drops below the zero-crossing threshold,
the driver forces DL low. This mechanism causes the
threshold between pulse-skipping PFM and nonskipping
PWM operation to coincide with the boundary between
continuous and discontinuous inductor-current opera-
tion (also known as the critical conduction point). The
load-current level at which the PFM/PWM crossover
occurs, I LOAD(SKIP) , is given by:
I LOAD ( SKIP ) = OUT IN OUT
f
The switching waveforms can appear noisy and asyn-
chronous when light loading causes pulse-skipping
operation, but this is a normal operating condition that
results in high light-load efficiency. Trade-off in PFM
noise vs. light-load efficiency is made by varying the
inductor value. Generally, low inductor values produce a
broader efficiency vs. load curve, while higher values
result in higher full-load efficiency (assuming that the coil
resistance remains fixed) and less output voltage ripple.
Penalties for using higher inductor values include larger
physical size and degraded load-transient response
(especially at low input-voltage levels).
Current Sense
Core SMPS Current Sense
The output current of each phase is sensed differentially.
A low offset voltage and high-gain differential current
amplifier at each phase allows low-resistance current-
sense resistors to be used to minimize power dissipa-
tion. Sensing the current at the output of each phase
offers advantages, including less noise sensitivity, more
accurate current sharing between phases, and the flex-
ibility of using either a current-sense resistor or the DC
resistance of the output inductor.
30
______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| MAX17482GTL+ | IC CTLR PWM DUAL IMVP-6.5 40TQFN |
| MAX1748EUE+T | IC DC-DC CONV TRPL LCD 16-TSSOP |
| MAX17497AATE+T | IC OFF-LINE CONVERTER 16TQFN |
| MAX17498AATE+T | IC OFF-LINE CONVERTER 16TQFN |
| MAX17500BEUB+ | IC REG CTRLR BST ISO PWM 10-UMAX |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX17482GTL+ | 功能描述:电压模式 PWM 控制器 NDA IC RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel |
| MAX17482GTL+T | 功能描述:电压模式 PWM 控制器 NDA IC RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel |
| MAX1748EUE | 功能描述:直流/直流开关转换器 RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| MAX1748EUE+ | 功能描述:直流/直流开关转换器 Triple-Output TFT LCD DC/DC Converters RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| MAX1748EUE+T | 功能描述:直流/直流开关转换器 Triple-Output TFT LCD DC/DC Converters RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
发布紧急采购，3分钟左右您将得到回复。