参数资料
型号: MAX17480GTL+T
厂商: Maxim Integrated Products
文件页数: 33/48页
文件大小: 0K
描述: IC CTRLR SERIAL VID 40-TQFN
产品培训模块: Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
标准包装: 2,500
应用: 处理器
电流 - 电源: 5mA
电源电压: 4.5 V ~ 5.5 V
工作温度: -40°C ~ 105°C
安装类型: 表面贴装
封装/外壳: 40-WFQFN 裸露焊盘
供应商设备封装: 40-TQFN-EP(5x5)
包装: 带卷 (TR)
AMD 2-/3-Output Mobile Serial
VID Controller
t START =
Combined-Mode Current Balance
When the core SMPSs are configured in combined
mode (GNDS1 or GNDS2 pulled to V DDIO ), the
MAX17480 current-mode architecture automatically
forces the individual phases to remain current bal-
anced. SMPS1 is the main voltage-control loop, and
SMPS2 maintains the current balance between the
phases. This control scheme regulates the peak induc-
tor current of each phase, forcing them to remain prop-
erly balanced. Therefore, the average inductor current
variation depends mainly on the variation in the current-
sense element and inductance value.
Peak Current Limit
The MAX17480 current-limit circuit employs a fast peak
inductor current-sensing algorithm. Once the current-
sense signal of the SMPS exceeds the peak current-limit
threshold, the PWM controller terminates the on-time.
See the Core Peak Inductor Current Limit (ILIM12) sec-
tion in the Core SMPS Design Procedure section.
Power-Up Sequence (POR, UVLO, PGD_IN)
Power-on reset (POR) occurs when V CC rises above
approximately 3V, resetting the fault latch and preparing
the controller for operation. The V CC undervoltage-lockout
(UVLO) circuitry inhibits switching until V CC rises above
4.25V (typ). The controller powers up the reference once
the system enables the controller V CC above 4.25V and
SHDN is driven high. With the reference in regulation, the
controller ramps the SMPS and NB voltages to the boot
voltage set by the SVC and SVD inputs:
V BOOT
( 1 mV /μ s )
The soft-start circuitry does not use a variable current
limit, so full output current is available immediately.
PWRGD becomes high impedance approximately 20μs
after the SMPS outputs reach regulation. The boot VID
is stored the first time PWRGD goes high. The
MAX17480 is in pulse-skipping mode during soft-start.
Figure 8 shows the MAX17480 startup sequence.
1
2
3
4
5
6
DC_IN
V DDIO
SVC/SVD
2-BIT BOOT VID
SERIAL MODE
BUS IDLE
SHDN
GNDS1 OR GNDS2
(VDD_PLANE_STRAP)
SMPS V OUT
7
PWRGD
20 μ s
10 μ s
BLANK
HIGH-Z
20 μ s
PGD_IN
RESET_L
8
Figure 8. Startup Sequence
______________________________________________________________________________________
33
相关PDF资料
PDF描述
MAX17482GTL+ IC CTLR PWM DUAL IMVP-6.5 40TQFN
MAX1748EUE+T IC DC-DC CONV TRPL LCD 16-TSSOP
MAX17497AATE+T IC OFF-LINE CONVERTER 16TQFN
MAX17498AATE+T IC OFF-LINE CONVERTER 16TQFN
MAX17500BEUB+ IC REG CTRLR BST ISO PWM 10-UMAX
相关代理商/技术参数
参数描述
MAX17482GTL+ 功能描述:电压模式 PWM 控制器 NDA IC RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel
MAX17482GTL+T 功能描述:电压模式 PWM 控制器 NDA IC RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel
MAX1748EUE 功能描述:直流/直流开关转换器 RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT
MAX1748EUE+ 功能描述:直流/直流开关转换器 Triple-Output TFT LCD DC/DC Converters RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT
MAX1748EUE+T 功能描述:直流/直流开关转换器 Triple-Output TFT LCD DC/DC Converters RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT