- 您现在的位置：买卖IC网 > PDF目录10753 > MAX19711ETN+ (Maxim Integrated Products)IC ANLG FRONT END 11MSPS 56-TQFN PDF资料下载
参数资料
| 型号： | MAX19711ETN+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 11/36页 |
| 文件大小： | 0K |
| 描述： | IC ANLG FRONT END 11MSPS 56-TQFN |
| 产品变化通告： | Product Discontinuation 09/Jun/2011 |
| 标准包装： | 43 |
| 位数： | 10 |
| 通道数： | 2 |
| 功率（瓦特）： | 37.5mW |
| 电压 - 电源，模拟： | 3V |
| 电压 - 电源，数字： | 3V |
| 封装/外壳： | 56-WFQFN 裸露焊盘 |
| 供应商设备封装： | 56-TQFN-EP（7x7） |
| 包装： | 管件 |
| 产品目录页面： | 1398 (CN2011-ZH PDF) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页当前第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页
MAX19711
10-Bit, 11Msps, Full-Duplex
Analog Front-End
______________________________________________________________________________________
19
Tx DAC Timing
Figure 6 shows the relationship among the clock, input
data, and analog outputs. Channel ID data is latched on
the falling edge of the clock signal, and channel QD data
is latched on the rising edge of the clock signal, at which
point both ID and QD outputs are simultaneously updated.
3-Wire Serial Interface and
Operation Modes
The 3-wire serial interface controls the MAX19711 oper-
ation modes as well as the three 12-bit aux-DACs and
the 10-bit aux-ADC. Upon power-up, program the
MAX19711 to operate in the desired mode. Use the 3-
wire serial interface to program the device for shutdown,
idle, standby, FD, Rx, Tx, aux-DAC controls, or aux-ADC
conversion. A 16-bit data register sets the mode control
as shown in Table 3. The 16-bit word is composed of
four control bits (A3–A0) and 12 data bits (D11–D0).
Data is shifted in MSB first (D11) and LSB last (A0) for-
mat. Table 4 shows the MAX19711 power-management
modes. Table 5 shows the SPI-controlled Tx, Rx, and FD
modes. The serial interface remains active in all modes.
SPI Register Description
Program the control bits, A3–A0, in the register as shown
in Table 3 to select the operating mode. Modify A3–A0 bits
to select from ENABLE-16, Aux-DAC1, Aux-DAC2, Aux-
DAC3, IOFFSET, QOFFSET, COMSEL, Aux-ADC,
ENABLE-8, and WAKEUP-SEL modes. ENABLE-16 is the
default operating mode (see Table 6). This mode allows for
shutdown, idle, and standby states as well as switching
between FAST, SLOW, Rx and Tx modes. Tables 4 and 5
show the required SPI settings for each mode.
In ENABLE-16 mode, the aux-DACs have independent
control bits E4, E5, and E6, bit E7 sets the Tx path full-
scale outputs, and bit E9 enables the aux-ADC. Table 7
shows the auxiliary DAC enable codes. Table 8 shows
the full-scale output selection. Table 9 shows the auxil-
iary ADC enable code. Bits E11 and E10 are reserved.
Program bits E11 and E10 to logic-low. Bits E3 and E8
are not used.
Modes Aux-DAC1, Aux-DAC2, and Aux-DAC3 select
the aux-DAC channels named DAC1, DAC2, and DAC3
and hold the data inputs for each DAC. Bits _D11–_D0
are the data inputs for each aux-DAC and can be pro-
grammed through SPI. The MAX19711 also includes
two 6-bit registers that can be programmed to adjust the
offsets for the Tx path ID and QD channels indepen-
dently (see Table 10). Use the COMSEL mode to select
the output common-mode voltage with bits CM1 and
CM0 (see Table 11). Use Aux-ADC mode to start the
auxiliary ADC conversion (see the 10-Bit, 333ksps
Auxiliary ADC section for details). Use ENABLE-8 mode
for faster enable and switching between shutdown, idle,
and standby states as well as switching between FAST,
SLOW, Rx and Tx modes and the FD mode.
The WAKEUP-SEL register selects the operating mode
that the MAX19711 is to enter immediately after coming
out of shutdown (Table 12). See the Wake-Up Function
section for more information.
0.63
CHANNEL EDGE
4.285
fIMAGE
1.3
fC
4.915
fCLK
FREQ (MHz)
NOT TO SCALE
-49.3dB
-15dB
-3dB
0dB
-56dB (min)
-57.1dB
OCCUPIED
CHANNEL
AMPLITUDE
CDMA
FILTER RESPONSE
DAC sin(x)/x
RESPONSE
Tx PATH:
SFDR = 75dBc
THD = -75dBc
SNR = 55.9dB
Figure 4. TD-SCDMA Filter Frequency Response
相关PDF资料 |
PDF描述 |
|---|---|
| V300C2M50BF3 | CONVERTER MOD DC/DC 2V 50W |
| MAX9140EXK+T | IC COMPARATOR R-R SC70-5 |
| V300C2M50BF | CONVERTER MOD DC/DC 2V 50W |
| B37950K1104K072 | CAP CER 0.1UF 100V 10% X7R 1210 |
| AD7195BCPZ | IC AFE 24BIT 4.8K 32LFSP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX19711ETN+ | 功能描述:ADC / DAC多通道 11Msps CODEC/AFE Full Duplex RoHS:否 制造商:Texas Instruments 转换速率: 分辨率:8 bit 接口类型:SPI 电压参考: 电源电压-最大:3.6 V 电源电压-最小:2 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-40 |
| MAX19711ETN+T | 功能描述:ADC / DAC多通道 11Msps CODEC/AFE Full Duplex RoHS:否 制造商:Texas Instruments 转换速率: 分辨率:8 bit 接口类型:SPI 电压参考: 电源电压-最大:3.6 V 电源电压-最小:2 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-40 |
| MAX19711ETN-T | 功能描述:ADC / DAC多通道 RoHS:否 制造商:Texas Instruments 转换速率: 分辨率:8 bit 接口类型:SPI 电压参考: 电源电压-最大:3.6 V 电源电压-最小:2 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-40 |
| MAX19711EVCMODU+ | 功能描述:数据转换 IC 开发工具 MAX19710/13 Eval Kit RoHS:否 制造商:Texas Instruments 产品:Demonstration Kits 类型:ADC 工具用于评估:ADS130E08 接口类型:SPI 工作电源电压:- 6 V to + 6 V |
| MAX19711EVKIT | 功能描述:数据转换 IC 开发工具 RoHS:否 制造商:Texas Instruments 产品:Demonstration Kits 类型:ADC 工具用于评估:ADS130E08 接口类型:SPI 工作电源电压:- 6 V to + 6 V |
发布紧急采购，3分钟左右您将得到回复。