参数资料
| 型号： | MAX3799ETJ+T |
| 厂商： | Maxim Integrated |
| 文件页数： | 28/36页 |
| 文件大小： | 0K |
| 描述： | IC AMP LIMITING VCSEL DVR 32TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 类型： | 激光二极管驱动器 |
| 数据速率： | 14Gbps |
| 通道数： | 1 |
| 电源电压： | 2.85 V ~ 3.63 V |
| 电流 - 电源： | 97mA |
| 电流 - 调制： | 12mA |
| 电流 - 偏置： | 15mA |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 32-WFQFN 裸露焊盘 |
| 供应商设备封装： | 32-TQFN-EP（5x5） |
| 包装： | 带卷 (TR) |
| 安装类型： | 表面贴装 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页当前第28页第29页第30页第31页第32页第33页第34页第35页第36页
MAX3799
1Gbps to 14Gbps, SFP+ Multirate Limiting
Amplifier and VCSEL Driver
impromptu deemphasis adjustment, it is recommended
that the DE_INC (MODINC[5]) bit is used. Use of this bit
increments or decrements the deemphasis code setting
by 1 LSB based on the sign of increment in the
MODINC[4:0] and, hence, the SET_IMOD[8:0] setting.
This helps maintain the BER while having the flexibility to
improve signal quality by adjusting deemphasis while
the transmit operation continues. This feature enables
glitchless deemphasis adjustment while maintaining
excellent BER performance.
Activating Receiver Output Deemphasis
The RXDE_EN bit must be set to 1 to enable the deem-
phasis function. Deemphasis decreases the output
amplitude at ROUT+/ROUT- by 25%. To maintain the
same output amplitude as before the activation of
deemphasis, the SET_CML register value needs to be
increased by 25%. When deemphasis is enabled, the
limiting amplifier AC performance is guaranteed up to
800mV P-P typical output amplitude. The SET_CML reg-
ister can be set from 0 to 255 bits, but it is important to
note that performance is guaranteed up to 215 bits.
Programming Pulse-Width Control
The eye crossing at the Tx output can be adjusted using
the SET_PWCTRL register. Table 6 shows these settings.
The sign of the number specifies the direction of pulse-
width distortion. The code of 1111 corresponds to a
balanced state for differential output. The pulse-width
distortion is bidirectional around the balanced state
(see the Typical Operating Characteristics section).
Programming CML Output Settings
Amplitude of the CML output stage is controlled by an
8-bit DAC register (SET_CML). The differential output
amplitude is up to 1000mV P-P with 4.6mV P-P resolution
(assuming an ideal 100 ? differential load). The guaran-
teed output CML DAC range is up to 215.
Output Voltage R OUT (mV P-P ) = 40 + 4.55 (SET_CML)
Select the Coupling Capacitor
For AC-coupling, the coupling capacitors C IN and
least a one-decade separation between f IN and the
low-frequency cutoff (f OC ) associated with the DC-off-
set cancellation circuit. A 1nF capacitor between CAZ1
and CAZ2 is recommended for the MAX3799.
Applications Information
Layout Considerations
To minimize inductance, keep the connections between
the MAX3799 output pins and laser diode as close as
possible. Optimize the laser diode performance by
placing a bypass capacitor as close as possible to the
laser anode. Use good high-frequency layout tech-
niques and multiple-layer boards with uninterrupted
ground planes to minimize EMI and crosstalk.
Exposed-Pad Package
The exposed pad on the 32-pin TQFN provides a very
low-thermal resistance path for heat removal from the IC.
The pad is also electrical ground on the MAX3799 and
must be soldered to the circuit board ground for proper
thermal and electrical performance. Refer to Application
Note 862: HFAN-08.1: Thermal Considerations of QFN
and Other Exposed-Paddle Packages for additional
information.
Laser Safety and IEC 825
Using the MAX3799 laser driver alone does not ensure
that a transmitter design is compliant with IEC 825. The
entire transmitter circuit and component selections
must be considered. Each user must determine the
level of fault tolerance required by the application, rec-
ognizing that Maxim products are neither designed nor
authorized for use as components in systems intended
for surgical implant into the body, for applications
intended to support or sustain life, or for any other
application in which the failure of a Maxim product
could create a situation where personal injury or death
could occur.
Table 6. Eye-Crossing Settings for
SET_PWCTRL
C OUT should be selected to minimize the receiver’s
deterministic jitter. Jitter is decreased as the input low-
frequency cutoff (f IN ) is decreased.
f IN = 1/[2 π (50)(C IN )]
The recommended C IN and C OUT is 0.1μF for the
MAX3799.
Select the Offset-Correction Capacitor
The capacitor between CAZ1 and CAZ2 determines the
time constant of the signal path DC-offset cancellation
loop. To maintain stability, it is important to keep at
SET_PWCTRL[3:0]
1000
1001
1010
1011
1100
1101
1110
1111
PWD
-7
-6
-5
-4
-3
-2
-1
0
SET_PWCTRL[3:0]
0111
0110
0101
0100
0011
0010
0001
0000
PWD
8
7
6
5
4
3
2
1
28
Maxim Integrated
相关PDF资料 |
PDF描述 |
|---|---|
| MAX3863ETJ+T | IC LASR DRVR 2.7GBPS 3.6V 32TQFN |
| MAX3869ETJ+ | IC LASER DRIVR 2CHAN 5.5V 32TQFP |
| MAX3946ETG+T | IC LASER DVR SFP 11.3GBPS 24TQFN |
| MAX3967AETG+T | IC SFP LED DRVR 24-TQFN |
| MAX3996CTP+T | IC LASR DRVR 2.5GBPS 5.5V 20TQFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX3799EVKIT+ | 功能描述:限幅放大器 Maxim Evaluation Kit RoHS:否 制造商:Micrel 输入电压范围（最大值）:3.6 V 工作电源电压:3.3 V 电源电流:40 mA 工作温度范围:- 40 C to + 85 C 封装 / 箱体:MSOP-10 封装:Tube |
| MAX379C/D | 功能描述:多路器开关 IC RoHS:否 制造商:Texas Instruments 通道数量:1 开关数量:4 开启电阻（最大值）:7 Ohms 开启时间（最大值）: 关闭时间（最大值）: 传播延迟时间:0.25 ns 工作电源电压:2.3 V to 3.6 V 工作电源电流: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UQFN-16 |
| MAX379CJE | 功能描述:多路器开关 IC RoHS:否 制造商:Texas Instruments 通道数量:1 开关数量:4 开启电阻（最大值）:7 Ohms 开启时间（最大值）: 关闭时间（最大值）: 传播延迟时间:0.25 ns 工作电源电压:2.3 V to 3.6 V 工作电源电流: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UQFN-16 |
| MAX379CPE | 功能描述:多路器开关 IC RoHS:否 制造商:Texas Instruments 通道数量:1 开关数量:4 开启电阻（最大值）:7 Ohms 开启时间（最大值）: 关闭时间（最大值）: 传播延迟时间:0.25 ns 工作电源电压:2.3 V to 3.6 V 工作电源电流: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UQFN-16 |
| MAX379CPE+ | 功能描述:多路器开关 IC 4:1 2Ch Fault-Prtct Analog MUX RoHS:否 制造商:Texas Instruments 通道数量:1 开关数量:4 开启电阻（最大值）:7 Ohms 开启时间（最大值）: 关闭时间（最大值）: 传播延迟时间:0.25 ns 工作电源电压:2.3 V to 3.6 V 工作电源电流: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UQFN-16 |
发布紧急采购，3分钟左右您将得到回复。