- 您现在的位置：买卖IC网 > PDF目录1843 > MAX5099ATJ+T (Maxim Integrated Products)IC REG BUCK SYNC ADJ DL 32TQFN PDF资料下载
参数资料
| 型号： | MAX5099ATJ+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 16/27页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK SYNC ADJ DL 32TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 类型： | 降压（降压） |
| 输出类型： | 可调式 |
| 输出数： | 2 |
| 输出电压： | 0.8 V ~ 17.1 V |
| 输入电压： | 4.5 V ~ 19 V |
| PWM 型： | 电压模式 |
| 频率 - 开关： | 200kHz ~ 2.2MHz |
| 电流 - 输出： | 1A，2A |
| 同步整流器： | 是 |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-WFQFN 裸露焊盘 |
| 包装： | 带卷 (TR) |
| 供应商设备封装： | 32-TQFN-EP（5x5） |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页当前第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页
Dual, 2.2MHz, Automotive Synchronous Buck
Converter with 80V Load-Dump Protection
V L
V IN
V L
V IN
V L
V+
V L
V+
OUTPUT2
DRAIN2
DRAIN1
OUTPUT1
OUTPUT2
DRAIN2
DRAIN1
OUTPUT1
SOURCE2
SOURCE1
SOURCE2
SOURCE1
N
DL2
MAX5099
DL1
N
N
DL2
MAX5099
DL1
N
FB2
FB1
R2
FB2
FB1
R1
V L
EN2
EN1
V L
V L
EN2
EN1
V L
PGOOD1
SEQUENCING—OUTPUT 2 DELAYED WITH RESPECT TO OUTPUT 1.
Figure 1. Power-Supply Sequencing Configurations
C2
R1/C1 AND R2/C2 ARE SIZED FOR REQUIRED SEQUENCING.
C1
Enable (EN1, EN2)
The MAX5099 dual converter provides separate enable
inputs, EN1 and EN2, to individually control or sequence
the output voltages. These active-high enable inputs are
TTL compatible. Driving EN_ high initiates soft-start of the
converter, and PGOOD_ goes logic-high when the con-
verter output voltage reaches the V TPGOOD_ threshold.
Driving EN_ low initiates a soft-stop of the converter. Use
EN1, EN2, and PGOOD1 for sequencing (see Figure 1).
Connect PGOOD1 to EN2 to make sure converter 1’s out-
put is within regulation before converter 2 starts. Add an
RC network from V L to EN1 and EN2 to delay the individ-
ual converter. Sequencing reduces input inrush current
and possible chattering. Connect EN_ to V L for always-on
operation.
PGOOD_
Converter 1 and converter 2 include power-good flags,
PGOOD1 and PGOOD2, respectively. Since PGOOD_
is an open-drain output and can sink 3mA while provid-
ing the TTL logic-low signal, pull PGOOD_ to a logic
voltage to provide a logic-level output. PGOOD1 goes
low when converter 1’s feedback (FB_) drops to 92.5%
(V TPGOOD_ ) of its nominal set point. The same is true
for converter 2. Connect PGOOD_ to SGND or leave
unconnected, if not used.
Current Limit
The internal high-side MOSFET switch current of each
converter is monitored during its on-time. When the
peak switch current crosses the current-limit threshold
of 3.45A (typ) and 2.1A (typ) for converter 1 and con-
verter 2, respectively, the on-cycle is terminated imme-
diately and the inductor is allowed to discharge. The
MOSFET switch is turned on at the next clock pulse ini-
tiating a new clock cycle.
In deep overload or short-circuit conditions when V FB
drops below 0.2V, the switching frequency is reduced to
1/4 x f SW to provide sufficient time for the inductor to dis-
charge. During overload conditions, if the voltage across
the inductor is not high enough to allow for the inductor
current to properly discharge, current runaway may
occur. Current runaway can destroy the device in spite of
internal thermal-overload protection. Reducing the
switching frequency during overload conditions prevents
current runaway.
Output Overvoltage Protection
The MAX5099 outputs are protected from output volt-
age overshoots due to input transients and shorting the
output to a high voltage. When the output voltage rises
over the overvoltage threshold, 114% (typ) nominal FB,
the overvoltage condition is triggered. When the over-
voltage condition is triggered on either channel, both
converters are immediately turned off, 20 Ω pulldown
switches from SOURCE_ to PGND are turned on to help
the output-voltage discharge, and the gate of the load-
dump protection external MOSFET is pulled low. The
device restarts as soon as both converter outputs dis-
charge, bringing both FB_ input voltages below 12.5%
of their nominal set points.
16
______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| MAX5943BEEE+ | IC FIREWIRE CURR LIMITER 16-QSOP |
| MAX5944ESE+T | IC FW CURR LIMITER DUAL 16-SOIC |
| MAX5951ETJ+ | IC REG CTRLR BUCK PWM VM 32-TQFN |
| MAX5974AETE+ | IC REG CTRLR FLYBACK PWM 16-TQFN |
| MAX5974FETE+ | IC REG CTRLR FLYBACK PWM 16-TQFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX5099EVKIT+ | 功能描述:电源管理IC开发工具 MAX5098A/99 Eval Kit RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| MAX509ACAP | 功能描述:数模转换器- DAC RoHS:否 制造商:Texas Instruments 转换器数量:1 DAC 输出端数量:1 转换速率:2 MSPs 分辨率:16 bit 接口类型:QSPI, SPI, Serial (3-Wire, Microwire) 稳定时间:1 us 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-14 封装:Tube |
| MAX509ACAP+ | 功能描述:数模转换器- DAC 8-Bit 4Ch Precision DAC RoHS:否 制造商:Texas Instruments 转换器数量:1 DAC 输出端数量:1 转换速率:2 MSPs 分辨率:16 bit 接口类型:QSPI, SPI, Serial (3-Wire, Microwire) 稳定时间:1 us 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-14 封装:Tube |
| MAX509ACAP+T | 功能描述:数模转换器- DAC 8-Bit 4Ch Precision DAC RoHS:否 制造商:Texas Instruments 转换器数量:1 DAC 输出端数量:1 转换速率:2 MSPs 分辨率:16 bit 接口类型:QSPI, SPI, Serial (3-Wire, Microwire) 稳定时间:1 us 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-14 封装:Tube |
| MAX509ACAP-T | 功能描述:数模转换器- DAC RoHS:否 制造商:Texas Instruments 转换器数量:1 DAC 输出端数量:1 转换速率:2 MSPs 分辨率:16 bit 接口类型:QSPI, SPI, Serial (3-Wire, Microwire) 稳定时间:1 us 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-14 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。