- 您现在的位置：买卖IC网 > PDF目录1848 > MAX8671XETL+T (Maxim Integrated Products)IC PMIC W/CHARGER 40-TQFN-EP PDF资料下载
参数资料
| 型号： | MAX8671XETL+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 25/44页 |
| 文件大小： | 0K |
| 描述： | IC PMIC W/CHARGER 40-TQFN-EP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 功能： | 充电管理 |
| 电池化学： | 锂离子（Li-Ion）、锂聚合物（Li-Pol） |
| 电源电压： | 4.1 V ~ 6.6 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 40-WFQFN 裸露焊盘 |
| 供应商设备封装： | 40-TQFN-EP（5x5） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页当前第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页
PMIC with Integrated Charger and
Smart Power Selector for Handheld Devices
with a single power input to operate from either an AC-
to-DC adapter or USB host (see Table 1).
A thermal-limiting circuit reduces the battery charger
rate and external power-source current to prevent the
MAX8671X from overheating.
System Load Switch
An internal 80m Ω (R BS ) MOSFET connects SYS to BAT
when no voltage source is available at DC or USB.
When an external source is detected at DC or USB, this
switch is opened and SYS is powered from the valid
input source through the Smart Power Selector.
When the system load requirements exceed the input
current limit, the battery supplies supplemental current
to the load through the internal system load switch. If
the system load continuously exceeds the input current
limit, the battery does not charge, even though external
power is connected. This is not expected to occur in
most cases because high loads usually occur only in
short peaks. During these peaks, battery energy is
used, but at all other times the battery charges.
USB Power Input (USB)
USB is a current-limited power input that supplies the
system (SYS) up to 500mA. The USB to SYS switch is a
linear regulator designed to operate in dropout. This lin-
ear regulator prevents the SYS voltage from exceeding
5.3V. USB is typically connected to the V BUS line of the
universal serial bus (USB) interface. As shown in Table
1, USB supports three different current limits that are
set with the PEN2 and USUS digital inputs. These cur-
rent limits are ideally suited for use with USB power.
The operating voltage range for USB is 4.1V to 6.6V,
but it can tolerate up to 14V without damage. When the
USB input voltage is below the undervoltage threshold
(V USBL , 4V typ) it is considered invalid. Similarly, if the
USB voltage is above the overvoltage threshold
(V USBH , 6.9V typ) it is considered invalid. When the
USB voltage is below the battery voltage, it is consid-
ered invalid. The USB power input is disconnected
when the USB voltage is invalid. As shown in Table 1,
when power is available at the DC input, it has priority
over the USB input. Bypass USB to ground with at least
a 4.7μF capacitor.
To support USB power sources at the USB input drive
PEN2 and USUS to select between three internally set
USB-related current limits as shown in Table 1. Choose
100mA for low-power USB mode. Choose 500mA for
high-power USB mode. Choose suspend to reduce the
USB current to 0.11mA (typ) for both USB suspend
mode and unconfigured OTG mode. To comply with
the USB 2.0 specification, each device must be initially
configured for low power. After USB enumeration, the
device can switch from low power to high power if
given permission from the USB host. The MAX8671X
does not perform enumeration. It is expected that the
system communicates with the USB host and com-
mands the MAX8671X through its PEN1, PEN2, and
USUS inputs. When the load exceeds the input current
limit, SYS drops to 82mV below BAT and the battery
supplies supplemental load current.
The MAX8671X reduces the USB current limit by 5%/°C
when the die temperature exceeds +100°C. The sys-
tem load (I SYS ) has priority over the charger current, so
input current is first reduced by lowering charge cur-
rent. If the junction temperature still reaches +120°C in
spite of charge current reduction, no input current is
drawn from USB; the battery supplies the entire load
and SYS is regulated below BAT by V BSREG . Note that
this on-chip thermal-limiting circuit is not related to and
operates independently from the thermistor input.
If the USB power input is not required, connect USB to
ground or leave it unconnected. When both DC and
USB inputs are powered, the DC input has priority.
______________________________________________________________________________________
25
相关PDF资料 |
PDF描述 |
|---|---|
| MAX8672ETD+T | IC MANAGE NIMH BACKUP 14-TDFN |
| MAX8677AETG+T | IC USB/AC ADP CHARGER 24-TQFN |
| MAX8677CETG+T | IC USB/AC ADP CHARGER 24-TQFN |
| MAX867EUA+ | IC REG BOOST ADJ 2.5MA 8UMAX |
| MAX8686ETL+T | IC REG BUCK SYNC ADJ 25A 40TQFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX8672ETD+T | 功能描述:电池管理 Backup Management IC for NiMH Batteries RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
| MAX8672EVKIT+ | 制造商:Maxim Integrated Products 功能描述:MAX8672 EVAL KIT - Rail/Tube |
| MAX8674EVKIT+ | 制造商:Maxim Integrated Products 功能描述:STANDARD PRODUCTS - Boxed Product (Development Kits) |
| MAX8676ELB+ | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
| MAX8676EWJ+T | 制造商:Maxim from Components Direct 功能描述:THE MAXIM MAX8676EWJ+T IS A USB HOT SWAP CONTROLLER. - Tape and Reel 制造商:Maxim 功能描述:The Maxim MAX8676EWJ+T is a USB Hot Swap Controller. |
发布紧急采购，3分钟左右您将得到回复。