- 您现在的位置：买卖IC网 > PDF目录1848 > MAX8671XETL+T (Maxim Integrated Products)IC PMIC W/CHARGER 40-TQFN-EP PDF资料下载
参数资料
| 型号： | MAX8671XETL+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 33/44页 |
| 文件大小： | 0K |
| 描述： | IC PMIC W/CHARGER 40-TQFN-EP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 功能： | 充电管理 |
| 电池化学： | 锂离子（Li-Ion）、锂聚合物（Li-Pol） |
| 电源电压： | 4.1 V ~ 6.6 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 40-WFQFN 裸露焊盘 |
| 供应商设备封装： | 40-TQFN-EP（5x5） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页当前第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页
PMIC with Integrated Charger and
Smart Power Selector for Handheld Devices
R FBH = R FBL × ? OUT ? 1 ?
The MAX8671X uses external resistor-dividers to set the
step-down output voltages between 1V and V SYS . Use at
least 10μA of bias current in these dividers to ensure no
change in the stability of the closed-loop system. To set
the output voltage, select a value for the resistor con-
nected between FB_ and AGND (R FBL ). The recom-
mended value is 100k Ω . Next, calculate the value of the
resistor connected from FB_ to the output (R FBH ):
? V ?
? 1 . 0 V ?
REG1, REG2, and REG3 are optimized for high, medi-
um, and low output voltages, respectively. The highest
overall efficiency occurs with V1 set to the highest out-
put voltage and V3 set to the lowest output voltage.
PWM
The MAX8671X operates in either auto-PWM or forced-
PWM modes. At light load, auto PWM switches only as
needed to supply the load to improve light-load effi-
ciency of the step-down converter. At higher load cur-
rents (~100mA), the step-down converter transitions to
fixed 2MHz switching. Forced PWM always operates
with a constant 2MHz switching frequency regardless
of the load. This is useful in low-noise applications.
Permanently connect PWM high for forced-PWM appli-
cations or low for auto-PWM applications. Do not
change PWM on-the-fly.
Step-Down Dropout and Minimum Duty Cycle
All the step-down regulators are capable of operating
in 100% duty-cycle dropout; however, REG1 has been
optimized for this mode of operation. During 100%
duty-cycle operation, the high-side p-channel MOSFET
turns on constantly, connecting the input to the output
through the inductor. The dropout voltage (V DO ) is cal-
culated as follows:
reduces switching noise in the controller. The imped-
ance of the input capacitor at the switching frequency
must be less than that of the source impedance of the
supply so that high-frequency switching currents do not
pass through the input source.
The step-down regulator power inputs are critical dis-
continuous current paths that require careful bypass-
ing. In the PCB layout, place the step-down regulator
input bypass capacitors as close as possible to each
pair of switching regulator power input pins (PV_ to
PG_) to minimize parasitic inductance. If making con-
nections to these caps through vias, be sure to use
multiple vias to ensure that the layout does not insert
excess inductance or resistance between the bypass
cap and the power pins.
The input capacitor must meet the input ripple current
requirement imposed by the step-down converter.
Ceramic capacitors are preferred due to their low ESR
and resilience to power-up surge currents. Choose the
input capacitor so that its temperature rise due to input
ripple current does not exceed about +10°C. For a
step-down DC-DC converter, the maximum input ripple
current is half of the output current. This maximum input
ripple current occurs when the step-down converter
operates at 50% duty factor (V IN = 2 x V OUT ).
Bypass each step-down regulator input with a 4.7μF
ceramic capacitor from PV_ to PG_. Use capacitors
that maintain their capacitance over temperature and
DC bias. Ceramic capacitors with an X7R or X5R tem-
perature characteristic generally perform well. The
capacitor voltage rating should be 6.3V or greater.
Step-Down Output Capacitors
The output capacitance keeps output ripple small and
ensures control loop stability. The output capacitor
must have low impedance at the switching frequency.
Ceramic, polymer, and tantalum capacitors are suit-
where:
V DO = I LOAD (R P + R L )
able, with ceramic exhibiting the lowest ESR and lowest
high-frequency impedance. The MAX8671X requires at
least 20μF of output capacitance, which is best
R P = p-channel power switch R DS(ON)
R L = external inductor ESR
The minimum duty cycle for all step-down regulators is
12.5% (typ), allowing a regulation voltage as low as 1V
over the full SYS operating range. REG3 is optimized
for low duty-cycle operation.
Step-Down Input Capacitors
The input capacitor in a step-down converter reduces
current peaks drawn from the power source and
achieved with two 10μF ceramic capacitors in parallel.
As the case sizes of ceramic surface-mount capacitors
decrease, their capacitance vs. DC bias voltage char-
acteristic becomes poor. Due to this characteristic, it is
possible for 0805 capacitors to perform well while 0603
capacitors of the same value might not. The MAX8671X
requires a nominal output capacitance of 20μF; howev-
er, after their DC bias voltage derating, the output
capacitance must be at least 15μF.
______________________________________________________________________________________
33
相关PDF资料 |
PDF描述 |
|---|---|
| MAX8672ETD+T | IC MANAGE NIMH BACKUP 14-TDFN |
| MAX8677AETG+T | IC USB/AC ADP CHARGER 24-TQFN |
| MAX8677CETG+T | IC USB/AC ADP CHARGER 24-TQFN |
| MAX867EUA+ | IC REG BOOST ADJ 2.5MA 8UMAX |
| MAX8686ETL+T | IC REG BUCK SYNC ADJ 25A 40TQFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX8672ETD+T | 功能描述:电池管理 Backup Management IC for NiMH Batteries RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
| MAX8672EVKIT+ | 制造商:Maxim Integrated Products 功能描述:MAX8672 EVAL KIT - Rail/Tube |
| MAX8674EVKIT+ | 制造商:Maxim Integrated Products 功能描述:STANDARD PRODUCTS - Boxed Product (Development Kits) |
| MAX8676ELB+ | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
| MAX8676EWJ+T | 制造商:Maxim from Components Direct 功能描述:THE MAXIM MAX8676EWJ+T IS A USB HOT SWAP CONTROLLER. - Tape and Reel 制造商:Maxim 功能描述:The Maxim MAX8676EWJ+T is a USB Hot Swap Controller. |
发布紧急采购，3分钟左右您将得到回复。