- 您现在的位置：买卖IC网 > PDF目录16753 > MAX8798ETX+ (Maxim Integrated Products)IC INTERNAL-SW BOOST REG 36-TQFN PDF资料下载
参数资料
| 型号： | MAX8798ETX+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 19/31页 |
| 文件大小： | 0K |
| 描述： | IC INTERNAL-SW BOOST REG 36-TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 50 |
| 应用： | LCD 监视器，笔记本电脑显示器 |
| 电流 - 电源： | 400µA |
| 电源电压： | 1.8 V ~ 6 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 36-WFQFN 裸露焊盘 |
| 供应商设备封装： | 36-TQFN 裸露焊盘（6x6） |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页当前第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页
Internal-Switch Boost Regulator with
Integrated 3-Channel Scan Driver for TFT LCDs
Linear Regulator (VL)
The MAX8798 includes an internal 3.3V linear regulator.
BOOST is the input of the linear regulator. The input volt-
age range is between 5V and 18V. The regulator powers
all the internal circuitry including the MOSFET gate dri-
ver. Bypass VL to AGND with a 0.22μF or greater ceram-
ic capacitor. Connect BOOST directly to the output of the
step-up regulator. This feature significantly improves the
efficiency at low input voltages.
Bootstrapping and Soft-Start
The MAX8798 features bootstrapping operation. In nor-
mal operation, the internal linear regulator supplies
power to the internal circuitry. Connect the input of the
linear regulator (BOOST) directly to the output of the
step-up regulator. The MAX8798 is enabled when the
voltages at IN and BOOST are above their UVLO
thresholds and the fault latch is not set. After being
enabled, the regulator starts open-loop switching to
generate the supply voltage for the linear regulator. The
internal reference block turns on when the VL voltage
exceeds its 2.7V (typ). When the reference voltage
reaches regulation, the PWM controller and the current-
limit circuit are enabled and the step-up regulator
enters soft-start. During soft-start, the main step-up reg-
ulator directly limits the peak inductor current, allowing
from zero up to the full current-limit value in 128 equal
current steps. The maximum load current is available
after the output voltage reaches regulation (that termi-
nates soft-start), or after the soft-start timer expires in
approximately 3ms. The soft-start routine minimizes
inrush current and voltage overshoot and ensures a
well-defined startup behavior.
Fault Protection
During steady-state operation, the MAX8798 monitors
the FB voltage. If the FB voltage does not exceed 1V
(typ), the MAX8798 activates an internal fault timer. If
there is a continuous fault for the fault-timer duration,
the MAX8798 sets the fault latch, turning off the main
step-up regulator and the linear regulator, disabling the
switch-control block and the operational amplifier.
Once the fault condition is removed, cycle the input
voltage to clear the fault latch and reactivate the
device. The fault-detection circuit is disabled during the
soft-start time.
The MAX8798 monitors BOOST for undervoltage and
overvoltage conditions. If the BOOST voltage is below
1.4V (typ) or above 19V (typ), the MAX8798 disables the
gate driver of the step-up regulator and prevents the
internal MOSFET from switching. The BOOST undervolt-
age and overvoltage conditions do not set the fault latch.
Operational Amplifier
The MAX8798 has an operational amplifier that is typi-
cally used to drive the LCD backplane (VCOM) or the
gamma-correction-divider string. The operational
amplifier features ±150mA output short-circuit current,
40V/μs slew rate, and 20MHz bandwidth. While the op
amp is a rail-to-rail input and output design, its accura-
cy is significantly degraded for input voltages within 1V
of its supply rails (BOOST and BGND).
Short-Circuit Current Limit
The operational amplifier limits short-circuit current to
approximately ±150mA if the output is directly shorted to
BOOST or to AGND. If the short-circuit condition per-
sists, the junction temperature of the IC rises until it
reaches the thermal-shutdown threshold (+160°C typ).
Once the junction temperature reaches the thermal-shut-
down threshold, an internal thermal sensor immediately
sets the thermal-fault latch, shutting off the main step-up
regulator, the linear regulator, the switch-control block,
and the operational amplifier. Those portions of the
device remain inactive until the input voltage is cycled.
Driving Pure Capacitive Loads
The operational amplifier is typically used to drive the
LCD backplane (VCOM) or the gamma-correction-
divider string. The LCD backplane consists of a distrib-
uted series capacitance and resistance, a load that can
be easily driven by the operational amplifier. However,
if the operational amplifier is used in an application with
a pure capacitive load, steps must be taken to ensure
stable operation.
As the operational amplifier’s capacitive load increases,
the amplifier’s bandwidth decreases and gain peaking
increases. A 5 Ω to 50 Ω small resistor placed between
VCOM and the capacitive load reduces peaking, but
also reduces the gain. An alternative method of reducing
peaking is to place a series RC network (snubber) in par-
allel with the capacitive load. The RC network does not
continuously load the output or reduce the gain. Typical
values of the resistor are between 100 Ω and 200 Ω and
the typical value of the capacitor is 10pF.
______________________________________________________________________________________
19
相关PDF资料 |
PDF描述 |
|---|---|
| 0210490404 | CABLE JUMPER 1.25MM .229M 32POS |
| A3CCB-1606M | IDC CABLE- AKC16B/AE16M/AKC16B |
| 322A134-12-0 | BOOT MOLDED |
| EBM24DCCI-S189 | CONN EDGECARD 48POS R/A .156 SLD |
| ECC22DRTN-S13 | CONN EDGECARD 44POS .100 EXTEND |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX8798ETX+ | 功能描述:显示驱动器和控制器 Internal-Switch Boost Regulator RoHS:否 制造商:Panasonic Electronic Components 工作电源电压:2.7 V to 5.5 V 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:QFN-44 封装:Reel |
| MAX8798ETX+T | 功能描述:显示驱动器和控制器 Internal-Switch Boost Regulator RoHS:否 制造商:Panasonic Electronic Components 工作电源电压:2.7 V to 5.5 V 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:QFN-44 封装:Reel |
| MAX8798EVCMAXQU+ | 功能描述:显示开发工具 MAX8798 Eval Kit RoHS:否 制造商:4D Systems 产品:4Display Shields 工具用于评估:?OLED-160-G1, ?OLED-160-G2 接口类型:Serial 工作电源电压:5 V |
| MAX8798EVKIT+ | 功能描述:显示开发工具 MAX8798 Eval Kit RoHS:否 制造商:4D Systems 产品:4Display Shields 工具用于评估:?OLED-160-G1, ?OLED-160-G2 接口类型:Serial 工作电源电压:5 V |
| MAX8799EVKIT+ | 制造商:Maxim Integrated Products 功能描述:SINGLE-PHASE AMD CPU - Boxed Product (Development Kits) |
发布紧急采购，3分钟左右您将得到回复。