- 您现在的位置：买卖IC网 > PDF目录16753 > MAX8798ETX+ (Maxim Integrated Products)IC INTERNAL-SW BOOST REG 36-TQFN PDF资料下载
参数资料
| 型号： | MAX8798ETX+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 23/31页 |
| 文件大小： | 0K |
| 描述： | IC INTERNAL-SW BOOST REG 36-TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 50 |
| 应用： | LCD 监视器，笔记本电脑显示器 |
| 电流 - 电源： | 400µA |
| 电源电压： | 1.8 V ~ 6 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 36-WFQFN 裸露焊盘 |
| 供应商设备封装： | 36-TQFN 裸露焊盘（6x6） |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页当前第23页第24页第25页第26页第27页第28页第29页第30页第31页
Internal-Switch Boost Regulator with
Integrated 3-Channel Scan Driver for TFT LCDs
8 V ? 3 . 3 V
? 3 . 3 V ? ?
? ? 0 . 85 ?
L = ? ? ? ? ? ? ≈ 2 . 8 μ H
Choosing an LIR of 0.5 and estimating efficiency of
85% at this operating point:
2
? 8 V ? ? 0 . 4 A × 1 . 2 MHz ? ? 0 . 5 ?
A 2.6μH inductor is chosen. Then, using the circuit’s
minimum input voltage (3V) and estimating efficiency of
80% at that operating point:
Figure 2 because of the high source impedance seen
in typical lab setups. Actual applications usually have
much lower source impedance since the step-up regu-
lator often runs directly from the output of another regu-
lated supply. Typically, C IN can be reduced below the
values used in Figure 2. Ensure a low noise supply at
IN by using adequate C IN . Alternatively, greater voltage
variation can be tolerated on C IN if IN is decoupled
from C IN using an RC lowpass filter (seen in Figure 2).
,
I IN ( DCMAX ) =
0.4A × 8V
3 V × 0 . 8
≈ 1 . 33 A
Rectifier Diode
The MAX8798’s high switching frequency demands a
high-speed rectifier. Schottky diodes are recommend-
ed for most applications because of their fast recovery
The ripple current and the peak current at that input
voltage are:
time and low forward voltage. In general, a 2A Schottky
diode complements the internal MOSFET well.
I RIPPLE =
3 V × ( 8 V ? 3 V )
2 . 6 μ H × 8 V × 1 . 2 MHz
≈ 0 . 6 A
Output Voltage Selection
The output voltage of the main step-up regulator is
adjusted by connecting a resistive voltage-divider from
I PEAK = 1 . 33 A +
0.6A
2
= 1 . 53 A
the output (V MAIN ) to AGND with the center tap con-
nected to FB (see Figure 2). Select R2 in the 10k Ω to
50k Ω range. Calculate R1 with the following equation:
R 1 = R 2 × ? MAIN ? 1 ?
V RIPPLE ( C ) ≈ MAIN ? MAIN IN ?
Output Capacitor Selection
The total output-voltage ripple has two components: the
capacitive ripple caused by the charging and discharg-
ing of the output capacitance, and the ohmic ripple due
to the capacitor’s equivalent series resistance (ESR):
V RIPPLE = V RIPPLE ( C ) + V RIPPLE ( ESR )
I ? V ? V ?
C OUT ? V MAIN f OSC ?
and:
? V ?
? V REF ?
where V REF , the step-up regulator’s feedback set point,
is 1.235V (typ). Place R1 and R2 close to the IC.
Loop Compensation
Choose R COMP to set the high-frequency integrator
gain for fast transient response. Choose C COMP to set
the integrator zero to maintain loop stability.
For low-ESR output capacitors, use the following equa-
tions to obtain stable performance and good transient
response:
V RIPPLE ( ESR ) ≈ I PEAK R ESR ( COUT )
where I PEAK is the peak inductor current (see the
Inductor Selection section). For ceramic capacitors, the
R COMP ≈
1000 × V IN × V OUT × C OUT
L × I MAIN ( MAX )
output-voltage ripple is typically dominated by
V RIPPLE(C) . The voltage rating and temperature charac-
teristics of the output capacitor must also be considered.
C COMP ≈
V OUT × C OUT
10 × I MAIN ( MAX ) × R COMP
Input Capacitor Selection
The input capacitor (C IN ) reduces the current peaks
drawn from the input supply and reduces noise injec-
tion into the IC. A 10μF ceramic capacitor is used in
To further optimize transient response, vary R COMP in
20% steps and C COMP in 50% steps while observing
transient response waveforms.
______________________________________________________________________________________
23
相关PDF资料 |
PDF描述 |
|---|---|
| 0210490404 | CABLE JUMPER 1.25MM .229M 32POS |
| A3CCB-1606M | IDC CABLE- AKC16B/AE16M/AKC16B |
| 322A134-12-0 | BOOT MOLDED |
| EBM24DCCI-S189 | CONN EDGECARD 48POS R/A .156 SLD |
| ECC22DRTN-S13 | CONN EDGECARD 44POS .100 EXTEND |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX8798ETX+ | 功能描述:显示驱动器和控制器 Internal-Switch Boost Regulator RoHS:否 制造商:Panasonic Electronic Components 工作电源电压:2.7 V to 5.5 V 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:QFN-44 封装:Reel |
| MAX8798ETX+T | 功能描述:显示驱动器和控制器 Internal-Switch Boost Regulator RoHS:否 制造商:Panasonic Electronic Components 工作电源电压:2.7 V to 5.5 V 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:QFN-44 封装:Reel |
| MAX8798EVCMAXQU+ | 功能描述:显示开发工具 MAX8798 Eval Kit RoHS:否 制造商:4D Systems 产品:4Display Shields 工具用于评估:?OLED-160-G1, ?OLED-160-G2 接口类型:Serial 工作电源电压:5 V |
| MAX8798EVKIT+ | 功能描述:显示开发工具 MAX8798 Eval Kit RoHS:否 制造商:4D Systems 产品:4Display Shields 工具用于评估:?OLED-160-G1, ?OLED-160-G2 接口类型:Serial 工作电源电压:5 V |
| MAX8799EVKIT+ | 制造商:Maxim Integrated Products 功能描述:SINGLE-PHASE AMD CPU - Boxed Product (Development Kits) |
发布紧急采购，3分钟左右您将得到回复。