- 您现在的位置：买卖IC网 > PDF目录16753 > MAX8798ETX+ (Maxim Integrated Products)IC INTERNAL-SW BOOST REG 36-TQFN PDF资料下载
参数资料
| 型号： | MAX8798ETX+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 27/31页 |
| 文件大小： | 0K |
| 描述： | IC INTERNAL-SW BOOST REG 36-TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 50 |
| 应用： | LCD 监视器，笔记本电脑显示器 |
| 电流 - 电源： | 400µA |
| 电源电压： | 1.8 V ~ 6 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 36-WFQFN 裸露焊盘 |
| 供应商设备封装： | 36-TQFN 裸露焊盘（6x6） |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页当前第27页第28页第29页第30页第31页
Internal-Switch Boost Regulator with
Integrated 3-Channel Scan Driver for TFT LCDs
PCB Layout and Grounding
Careful PCB layout is important for proper operation.
Use the following guidelines for good PCB layout:
BOOST and VL bypass capacitor ground connec-
tions, and the device’s exposed backside paddle.
Connect the AGND and PGND islands by connect-
?
Minimize the area of high-current loops by placing
the inductor, output diode, and output capacitors
near the input capacitors and near LX and PGND.
ing the PGND pin directly to the exposed backside
paddle. Make no other connections between these
separate ground planes.
The high-current input loop goes from the positive
terminal of the input capacitor to the inductor, to the
IC’s LX pin, out of PGND, and to the input capaci-
tor’s negative terminal. The high-current output loop
is from the positive terminal of the input capacitor to
the inductor, to the output diode (D1), to the posi-
tive terminal of the output capacitors, reconnecting
between the output capacitor and input capacitor
ground terminals. Connect these loop components
with short, wide connections. Avoid using vias in
the high-current paths. If vias are unavoidable, use
many vias in parallel to reduce resistance and
inductance.
?
?
Place the feedback-voltage-divider resistors as
close as possible to the feedback pin. The divider’s
center trace should be kept short. Placing the resis-
tors far away causes the FB trace to become an
antenna that can pick up switching noise. Care
should be taken to avoid running the feedback
trace near LX or the switching nodes in the charge
pumps.
Place the IN pin and VL pin bypass capacitors as
close as possible to the device. The ground con-
nections of the IN and VL bypass capacitors should
be connected directly to the AGND pin with a wide
trace.
?
Create a power ground island (PGND) consisting of
the input and output capacitor grounds, PGND pin,
and any charge-pump components. Connect all
these together with short, wide traces or a small
ground plane. Maximizing the width of the power
ground traces improves efficiency and reduces out-
put-voltage ripple and noise spikes. Create an ana-
log ground plane (AGND) consisting of the AGND
?
?
Minimize the length and maximize the width of the
traces between the output capacitors and the load
for best transient responses.
Minimize the size of the LX node while keeping it
wide and short. Keep the LX node away from the
feedback node and analog ground. Use DC traces
as shield if necessary.
pin, all the feedback-divider ground connections, the
operational-amplifier-divider ground connections,
the COMP capacitor ground connection, the
Refer to the MAX8798 evaluation kit for an example of
proper board layout.
______________________________________________________________________________________
27
相关PDF资料 |
PDF描述 |
|---|---|
| 0210490404 | CABLE JUMPER 1.25MM .229M 32POS |
| A3CCB-1606M | IDC CABLE- AKC16B/AE16M/AKC16B |
| 322A134-12-0 | BOOT MOLDED |
| EBM24DCCI-S189 | CONN EDGECARD 48POS R/A .156 SLD |
| ECC22DRTN-S13 | CONN EDGECARD 44POS .100 EXTEND |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX8798ETX+ | 功能描述:显示驱动器和控制器 Internal-Switch Boost Regulator RoHS:否 制造商:Panasonic Electronic Components 工作电源电压:2.7 V to 5.5 V 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:QFN-44 封装:Reel |
| MAX8798ETX+T | 功能描述:显示驱动器和控制器 Internal-Switch Boost Regulator RoHS:否 制造商:Panasonic Electronic Components 工作电源电压:2.7 V to 5.5 V 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:QFN-44 封装:Reel |
| MAX8798EVCMAXQU+ | 功能描述:显示开发工具 MAX8798 Eval Kit RoHS:否 制造商:4D Systems 产品:4Display Shields 工具用于评估:?OLED-160-G1, ?OLED-160-G2 接口类型:Serial 工作电源电压:5 V |
| MAX8798EVKIT+ | 功能描述:显示开发工具 MAX8798 Eval Kit RoHS:否 制造商:4D Systems 产品:4Display Shields 工具用于评估:?OLED-160-G1, ?OLED-160-G2 接口类型:Serial 工作电源电压:5 V |
| MAX8799EVKIT+ | 制造商:Maxim Integrated Products 功能描述:SINGLE-PHASE AMD CPU - Boxed Product (Development Kits) |
发布紧急采购，3分钟左右您将得到回复。