- 您现在的位置：买卖IC网 > PDF目录80382 > MB9AF314MPMC 32-BIT, FLASH, 40 MHz, RISC MICROCONTROLLER, PQFP80 PDF资料下载
参数资料
| 型号： | MB9AF314MPMC |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 32-BIT, FLASH, 40 MHz, RISC MICROCONTROLLER, PQFP80 |
| 封装： | 0.50 MM PITCH, PLASTIC, LQFP-80 |
| 文件页数： | 34/114页 |
| 文件大小： | 1357K |
| 代理商： | MB9AF314MPMC |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页当前第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页
ATmega48PA/88PA/168PA [DATASHEET]
9223F–AVR–04/14
26
Main purpose of the delay is to keep the AVR in reset until it is supplied with minimum VCC. The delay will not monitor the
actual voltage and it will be required to select a delay longer than the VCC rise time. If this is not possible, an internal or
external brown-out detection circuit should be used. A BOD circuit will ensure sufficient VCC before it releases the reset, and
the time-out delay can be disabled. Disabling the time-out delay without utilizing a brown-out detection circuit is not
recommended.
The oscillator is required to oscillate for a minimum number of cycles before the clock is considered stable. An internal ripple
counter monitors the oscillator output clock, and keeps the internal reset active for a given number of clock cycles. The reset
is then released and the device will start to execute. The recommended oscillator start-up time is dependent on the clock
type, and varies from 6 cycles for an externally applied clock to 32K cycles for a low frequency crystal.
The start-up sequence for the clock includes both the time-out delay and the start-up time when the device starts up from
reset. When starting up from power-save or power-down mode, VCC is assumed to be at a sufficient level and only the start-
up time is included.
9.3
Low Power Crystal Oscillator
Pins XTAL1 and XTAL2 are input and output, respectively, of an inverting amplifier which can be configured for use as an
on-chip oscillator, as shown in Figure 9-2 on page 26. Either a quartz crystal or a ceramic resonator may be used.
This crystal oscillator is a low power oscillator, with reduced voltage swing on the XTAL2 output. It gives the lowest power
consumption, but is not capable of driving other clock inputs, and may be more susceptible to noise in noisy environments. In
these cases, refer to the Section 9.4 “Full Swing Crystal Oscillator” on page 27.
C1 and C2 should always be equal for both crystals and resonators. The optimal value of the capacitors depends on the
crystal or resonator in use, the amount of stray capacitance, and the electromagnetic noise of the environment. Some initial
guidelines for choosing capacitors for use with crystals are given in Table 9-3. For ceramic resonators, the capacitor values
given by the manufacturer should be used.
Figure 9-2. Crystal Oscillator Connections
The low power oscillator can operate in three different modes, each optimized for a specific frequency range. The operating
mode is selected by the fuses CKSEL3...1 as shown in Table 9-3.
Table 9-3.
Low Power Crystal Oscillator Operating Modes(3)
Frequency Range
(MHz)
Recommended Range for
Capacitors C1 and C2 (pF)
CKSEL3...1(1)
0.4 - 0.9
–
100(2)
0.9 - 3.0
12 - 22
101
3.0 - 8.0
12 - 22
110
8.0 - 16.0
12 - 22
111
Notes: 1.
This is the recommended CKSEL settings for the difference frequency ranges.
2.
This option should not be used with crystals, only with ceramic resonators.
3.
If the crystal frequency exceeds the specification of the device (depends on VCC), the CKDIV8 fuse can be
programmed in order to divide the internal frequency by 8. It must be ensured that the resulting divided clock
meets the frequency specification of the device.
C2
XTAL2 (TOSC2)
XTAL1 (TOSC1)
GND
C1
相关PDF资料 |
PDF描述 |
|---|---|
| MB89537APV4 | 8-BIT, MROM, 12.5 MHz, MICROCONTROLLER, PBCC64 |
| M38062E6GP | 8-BIT, OTPROM, 8 MHz, MICROCONTROLLER, PQFP80 |
| MSM80C31F-GS-VIK | 8-BIT, 12 MHz, MICROCONTROLLER, PQFP44 |
| MSM83C154-1GS-K | 8-BIT, MROM, 16 MHz, MICROCONTROLLER, PQFP44 |
| MC68HC11A8CFU1 | 8-BIT, MROM, 3 MHz, MICROCONTROLLER, PQFP64 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MB9AF314MPMC-G-JNE1 | 制造商:FUJITSU 功能描述:MCU 32BIT CORTEX-M3 FM3 80LQFP |
| MB9AF314NABGL-GE1 | 制造商:FUJITSU 功能描述: |
| MB9AF314NAPF-G-JNE1 | 功能描述:IC MCU 32BIT 256KB FLASH 100QFP 制造商:cypress semiconductor corp 系列:FM3 MB9A310A 包装:托盘 零件状态:在售 核心处理器:ARM? Cortex?-M3 核心尺寸:32-位 速度:40MHz 连接性:CSIO，EBI/EMI，I2C，LIN，UART/USART，USB 外设:DMA，LVD，POR，PWM，WDT I/O 数:83 程序存储容量:256KB（256K x 8） 程序存储器类型:闪存 EEPROM 容量:- RAM 容量:32K x 8 电压 - 电源（Vcc/Vdd）:2.7 V ~ 5.5 V 数据转换器:A/D 16x12b 振荡器类型:内部 工作温度:-40°C ~ 105°C（TA） 封装/外壳:100-BQFP 供应商器件封装:100-PQFP（20x14） 标准包装:66 |
| MB9AF314NAPMC-G-JNE2 | 功能描述:ARM? Cortex?-M3 FM3 MB9A310A Microcontroller IC 32-Bit 40MHz 256KB (256K x 8) FLASH 100-LQFP (14x14) 制造商:cypress semiconductor corp 系列:FM3 MB9A310A 包装:托盘 零件状态:有效 核心处理器:ARM? Cortex?-M3 核心尺寸:32-位 速度:40MHz 连接性:CSIO，EBI/EMI，I2C，LIN，UART/USART，USB 外设:DMA，LVD，POR，PWM，WDT I/O 数:83 程序存储容量:256KB（256K x 8） 程序存储器类型:闪存 EEPROM 容量:- RAM 容量:32K x 8 电压 - 电源（Vcc/Vdd）:2.7 V ~ 5.5 V 数据转换器:A/D 16x12b 振荡器类型:内部 工作温度:-40°C ~ 105°C（TA） 封装/外壳:100-LQFP 供应商器件封装:100-LQFP（14x14） 标准包装:90 |
| MB9AF314NBGL-GE1 | 制造商:FUJITSU 功能描述: 制造商:FUJITSU 功能描述:MCU 32BIT CORTEX-M3 FM3 112BGA 制造商:FUJITSU 功能描述:MCU, 32BIT, CORTEX-M3, FM3, 112BGA 制造商:FUJITSU 功能描述:MCU, 32BIT, CORTEX-M3, FM3, 112BGA, Controller Family/Series:ARM Cortex-M3, Core 制造商:FUJITSU 功能描述:MCU, 32BIT, CORTEX-M3, FM3, 112BGA, Controller Family/Series:ARM Cortex-M3, Core Size:32bit, No. of I/O's:83, Supply Voltage Min:2.7V, Supply Voltage Max:5.5V, Digital IC Case Style:BGA, No. of Pins:112, Program Memory Size:256KB, , RoHS Compliant: Yes |
发布紧急采购，3分钟左右您将得到回复。