参数资料
型号: MB9AF314MPMC
元件分类: 微控制器/微处理器
英文描述: 32-BIT, FLASH, 40 MHz, RISC MICROCONTROLLER, PQFP80
封装: 0.50 MM PITCH, PLASTIC, LQFP-80
文件页数: 80/114页
文件大小: 1357K
代理商: MB9AF314MPMC
ATmega48PA/88PA/168PA [DATASHEET]
9223F–AVR–04/14
68
14.2.5 Digital Input Enable and Sleep Modes
As shown in Figure 14-2 on page 65, the digital input signal can be clamped to ground at the input of the Schmitt Trigger.
The signal denoted SLEEP in the figure, is set by the MCU sleep controller in power-down mode, power-save mode, and
standby mode to avoid high power consumption if some input signals are left floating, or have an analog signal level close to
VCC/2.
SLEEP is overridden for port pins enabled as external interrupt pins. If the external interrupt request is not enabled, SLEEP
is active also for these pins. SLEEP is also overridden by various other alternate functions as described in
If a logic high level (“one”) is present on an asynchronous external interrupt pin configured as “Interrupt on rising edge, falling
edge, or any logic change on pin” while the external interrupt is not enabled, the corresponding external interrupt flag will be
set when resuming from the above mentioned Sleep mode, as the clamping in these sleep mode produces the requested
logic change.
14.2.6 Unconnected Pins
If some pins are unused, it is recommended to ensure that these pins have a defined level. Even though most of the digital
inputs are disabled in the deep sleep modes as described above, floating inputs should be avoided to reduce current
consumption in all other modes where the digital inputs are enabled (reset, active mode and Idle mode).
The simplest method to ensure a defined level of an unused pin, is to enable the internal pull-up. In this case, the pull-up will
be disabled during reset. If low power consumption during reset is important, it is recommended to use an external pull-up or
pull-down. Connecting unused pins directly to VCC or GND is not recommended, since this may cause excessive currents if
the pin is accidentally configured as an output.
相关PDF资料
PDF描述
MB89537APV4 8-BIT, MROM, 12.5 MHz, MICROCONTROLLER, PBCC64
M38062E6GP 8-BIT, OTPROM, 8 MHz, MICROCONTROLLER, PQFP80
MSM80C31F-GS-VIK 8-BIT, 12 MHz, MICROCONTROLLER, PQFP44
MSM83C154-1GS-K 8-BIT, MROM, 16 MHz, MICROCONTROLLER, PQFP44
MC68HC11A8CFU1 8-BIT, MROM, 3 MHz, MICROCONTROLLER, PQFP64
相关代理商/技术参数
参数描述
MB9AF314MPMC-G-JNE1 制造商:FUJITSU 功能描述:MCU 32BIT CORTEX-M3 FM3 80LQFP
MB9AF314NABGL-GE1 制造商:FUJITSU 功能描述:
MB9AF314NAPF-G-JNE1 功能描述:IC MCU 32BIT 256KB FLASH 100QFP 制造商:cypress semiconductor corp 系列:FM3 MB9A310A 包装:托盘 零件状态:在售 核心处理器:ARM? Cortex?-M3 核心尺寸:32-位 速度:40MHz 连接性:CSIO,EBI/EMI,I2C,LIN,UART/USART,USB 外设:DMA,LVD,POR,PWM,WDT I/O 数:83 程序存储容量:256KB(256K x 8) 程序存储器类型:闪存 EEPROM 容量:- RAM 容量:32K x 8 电压 - 电源(Vcc/Vdd):2.7 V ~ 5.5 V 数据转换器:A/D 16x12b 振荡器类型:内部 工作温度:-40°C ~ 105°C(TA) 封装/外壳:100-BQFP 供应商器件封装:100-PQFP(20x14) 标准包装:66
MB9AF314NAPMC-G-JNE2 功能描述:ARM? Cortex?-M3 FM3 MB9A310A Microcontroller IC 32-Bit 40MHz 256KB (256K x 8) FLASH 100-LQFP (14x14) 制造商:cypress semiconductor corp 系列:FM3 MB9A310A 包装:托盘 零件状态:有效 核心处理器:ARM? Cortex?-M3 核心尺寸:32-位 速度:40MHz 连接性:CSIO,EBI/EMI,I2C,LIN,UART/USART,USB 外设:DMA,LVD,POR,PWM,WDT I/O 数:83 程序存储容量:256KB(256K x 8) 程序存储器类型:闪存 EEPROM 容量:- RAM 容量:32K x 8 电压 - 电源(Vcc/Vdd):2.7 V ~ 5.5 V 数据转换器:A/D 16x12b 振荡器类型:内部 工作温度:-40°C ~ 105°C(TA) 封装/外壳:100-LQFP 供应商器件封装:100-LQFP(14x14) 标准包装:90
MB9AF314NBGL-GE1 制造商:FUJITSU 功能描述: 制造商:FUJITSU 功能描述:MCU 32BIT CORTEX-M3 FM3 112BGA 制造商:FUJITSU 功能描述:MCU, 32BIT, CORTEX-M3, FM3, 112BGA 制造商:FUJITSU 功能描述:MCU, 32BIT, CORTEX-M3, FM3, 112BGA, Controller Family/Series:ARM Cortex-M3, Core 制造商:FUJITSU 功能描述:MCU, 32BIT, CORTEX-M3, FM3, 112BGA, Controller Family/Series:ARM Cortex-M3, Core Size:32bit, No. of I/O's:83, Supply Voltage Min:2.7V, Supply Voltage Max:5.5V, Digital IC Case Style:BGA, No. of Pins:112, Program Memory Size:256KB, , RoHS Compliant: Yes