- 您现在的位置：买卖IC网 > PDF目录181329 > MBM29DL161TD-70PFTR-E1 (SPANSION LLC) 1M X 16 FLASH 3V PROM, 70 ns, PDSO48 PDF资料下载
参数资料
| 型号： | MBM29DL161TD-70PFTR-E1 |
| 厂商： | SPANSION LLC |
| 元件分类： | PROM |
| 英文描述： | 1M X 16 FLASH 3V PROM, 70 ns, PDSO48 |
| 封装： | PLASTIC, REVERSE, TSOP-48 |
| 文件页数： | 24/80页 |
| 文件大小： | 565K |
| 代理商： | MBM29DL161TD-70PFTR-E1 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页当前第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页
MBM29DL16XTD/BD-70/90
Retired Product DS05-20874-8E_July 12, 2007
30
When using the RESET pin only, a CMOS standby mode is achieved with RESET input held at VSS ± 0.3 V
(CE = “H” or “L”). Under this condition the current is consumed is less than 5
μA Max. Once the RESET pin is
taken high, the device requires tRH of wake up time before outputs are valid for read access.
In the standby mode the outputs are in the high impedance state, independent of the OE input.
Automatic Sleep Mode
There is a function called automatic sleep mode to restrain power consumption during read-out of
MBM29DL16XTD/BD data. This mode can be used effectively with an application requested low power
consumption such as handy terminals.
To activate this mode, MBM29DL16XTD/BD automatically switch themselves to low power mode when
MBM29DL16XTD/BD addresses remain stably during access fine of 150 ns. It is not necessary to control CE,
WE, and OE on the mode. Under the mode, the current consumed is typically 1
μA (CMOS Level).
During simultaneous operation, VCC active current (ICC2) is required.
Since the data are latched during this mode, the data are read-out continuously. If the addresses are changed,
the mode is canceled automatically and MBM29DL16XTD/BD read-out the data for changed addresses.
Output Disable
With the OE input at a logic high level (VIH), output from the devices are disabled. This will cause the output pins
to be in a high impedance state.
Autoselect
The autoselect mode allows the reading out of a binary code from the devices and will identify its manufacturer
and type. This mode is intended for use by programming equipment for the purpose of automatically matching
the devices to be programmed with its corresponding programming algorithm. This mode is functional over the
entire temperature range of the devices.
To activate this mode, the programming equipment must force VID (11.5 V to 12.5 V) on address pin A9. Two
identifier bytes may then be sequenced from the devices outputs by toggling address A0 from VIL to VIH. All
addresses are DON’T CARES except A0, A1, and A6 (A-1). (See “MBM29DL16XTD/BD User Bus Operations
Tables (BYTE = VIH and BYTE = VIL)” in
■DEVICE BUS OPERATION.)
The manufacturer and device codes may also be read via the command register, for instances when the
MBM29DL16XTD/BD are erased or programmed in a system without access to high voltage on the A9 pin. The
command sequence is illustrated in “MBM29DL16XTD/BD Command Definitions Table” (in
■DEVICE BUS
OPERATION). (Refer to Autoselect Command section.)
Byte 0 (A0 = VIL) represents the manufacturer’s code (Fujitsu = 04h) and word 1 (A0 = VIH) represents the device
identifier code (MBM29DL161TD = 36h and MBM29DL161BD = 39h for
×8 mode; MBM29DL161TD = 2236h
and MBM29DL161BD = 2239h for
×16 mode), (MBM29DL162TD = 2Dh and MBM29DL162BD = 2Eh for ×8
mode; MBM29DL162TD = 222Dh and MBM29DL162BD = 222Eh for
×16 mode), (MBM29DL163TD = 28h and
MBM29DL163BD = 2Bh for
×8 mode; MBM29DL163TD = 2228h and MBM29DL163BD = 222Bh for ×16 mode),
(MBM29DL164TD = 33h and MBM29DL164BD = 35h for
×8 mode; MBM29DL164TD = 2233h and
MBM29DL164BD = 2235h for
×16 mode). These two bytes/words are given in “MBM29DL161TD/BD,
MBM29DL162TD/BD, MBM29DL163TD/BD and MBM29DL164TD/BD Sector Group Protection Verify
Autoselect Codes Tables” and these “Extended Autoselect Code Tables” in
■DEVICE BUS OPERATION. All
identifiers for manufactures and device will exhibit odd parity with DQ7 defined as the parity bit. In order to read
the proper device codes when executing the autoselect, A1 must be VIL. (See “MBM29DL161TD/BD,
MBM29DL162TD/BD, MBM29DL163TD/BD and MBM29DL164TD/BD Sector Group Protection Verify
Autoselect Codes Tables” and these “Extended Autoselect Code Tables” in
■DEVICE BUS OPERATION.)
In case of applying VID on A9, since both Bank 1 and Bank 2 enters Autoselect mode, the simultenous operation
can not be executed.
相关PDF资料 |
PDF描述 |
|---|---|
| MBM29LV651UE-90TN | 4M X 16 FLASH 3V PROM, 90 ns, PDSO48 |
| MBM29LV800TA-12PFTR-X | 1M X 8 FLASH 3V PROM, 120 ns, PDSO48 |
| MBM29PL32BM10TN-E1 | 2M X 16 FLASH 3V PROM, 100 ns, PDSO48 |
| MBM29PL32TM90TN-E1 | 2M X 16 FLASH 3V PROM, 90 ns, PDSO48 |
| MBN400GR12A | 400 A, 1200 V, N-CHANNEL IGBT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MBM29DL161TD-90PBT | 制造商:SPANSION 制造商全称:SPANSION 功能描述:FLASH MEMORY CMOS 16M (2M X 8/1M X 16) BIT Dual Operation |
| MBM29DL161TD-90PFTN | 制造商:SPANSION 制造商全称:SPANSION 功能描述:FLASH MEMORY CMOS 16M (2M X 8/1M X 16) BIT Dual Operation |
| MBM29DL161TD-90PFTR | 制造商:SPANSION 制造商全称:SPANSION 功能描述:FLASH MEMORY CMOS 16M (2M X 8/1M X 16) BIT Dual Operation |
| MBM29DL161TE | 制造商:FUJITSU 制造商全称:Fujitsu Component Limited. 功能描述:16M (2MX8/1MX16) BIT Dual Operation |
| MBM29DL161TE-12 | 制造商:FUJITSU 制造商全称:Fujitsu Component Limited. 功能描述:16M (2M X 8/1M X 16) BIT Dual Operation |
发布紧急采购，3分钟左右您将得到回复。