- 您现在的位置：买卖IC网 > PDF目录299463 > MBM29F800TA-70PFTN-E1 (SPANSION LLC) 512K X 16 FLASH 5V PROM, 70 ns, PDSO48 PDF资料下载
参数资料
| 型号： | MBM29F800TA-70PFTN-E1 |
| 厂商： | SPANSION LLC |
| 元件分类： | PROM |
| 英文描述： | 512K X 16 FLASH 5V PROM, 70 ns, PDSO48 |
| 封装： | PLASTIC, TSOP1-48 |
| 文件页数： | 7/49页 |
| 文件大小： | 693K |
| 代理商： | MBM29F800TA-70PFTN-E1 |
第1页第2页第3页第4页第5页第6页当前第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页
MBM29F800TA-55/-70/-90/MBM29F800BA-55/-70/-90
14
Write
Device erasure and programming are accomplished via the command register. The contents of the register serve
as inputs to the internal state machine. The state machine outputs dictate the function of the device.
The command register itself does not occupy any addressable memory location. The register is a latch used to
store the commands, along with the address and data information needed to execute the command. The
command register is written by bringing WE to VIL, while CE is at VIL and OE is at VIH. Addresses are latched on
the falling edge of WE or CE, whichever happens later; while data is latched on the rising edge of WE or CE,
whichever happens first. Standard microprocessor write timings are used.
Refer to “s AC CHARACTERISTICDS” and “s TIMING DIAGRAM” for specific timing parameters.
Sector Protection
The MBM29F800TA/BA features hardware sector protection. This feature will disable both program and erase
operations in any number of sectors (0 through 18). The sector protection feature is enabled using programming
equipment at the user’s site. The device is shipped with all sectors unprotected.
To activate this mode, the programming equipment must force VID on address pin A9 and control pin OE, (suggest
VID = 11.5V), CE = VIL, and A6 = VIL. The sector addresses (A18, A17, A16, A15, A14, A13, and A12) should be set to
the sector to be protected. “Sector Address Tables (MBM29F800TA)” and “Sector Address Tables
(MBM29F800BA)” in s FLEXIBLE SECTOR ERASE ARCHITECTURE define the sector address for each of
the nineteen (19) individual sectors. Programming of the protection circuitry begins on the falling edge of the
WE pulse and is terminated with the rising edge of the same. Sector addresses must be held constant during
the WE pulse. See “Sector Protection Timing Diagram” in s TIMING DIAGRAM and “Sector Protection Algorithm”
in s FLOW CHART for sector protection waveforms and algorithm.
To verify programming of the protection circuitry, the programming equipment must force VID on address pin A9
with CE and OE at VIL and WE at VIH. Scanning the sector addresses (A18, A17, A16, A15, A14, A13, and A12) while
(A6, A1, A0) = (0, 1, 0) will produce a logical “1” code at device output DQ0 for a protected sector. Otherwise the
devices will read 00h for unprotected sector. In this mode, the lower order addresses, except for A0, A1, and A6
are DON’T CARES. Address locations with A1 = VIL are reserved for Autoselect manufacturer and device codes.
A-1 requires to apply to VIL on byte mode.
It is also possible to determine if a sector is protected in the system by writing an Autoselect command. Performing
a read operation at the address location XX02h, where the higher order addresses (A18, A17, A16, A15, A14, A13,
and A12) are the desired sector address will produce a logical “1” at DQ0 for a protected sector. See
“MBM29F800TA/BA Sector Protection Verify Autoselect Codes” and “Expanded Autoselect Code Table” in
s DEVICE BUS OPERATION for Autoselect codes.
Temporary Sector Unprotection
This feature allows temporary unprotection of previously protected sectors of the MBM29F800TA/BA device in
order to change data. The Sector Unprotection mode is activated by setting the RESET pin to high voltage
(12 V). During this mode, formerly protected sectors can be programmed or erased by selecting the sector
addresses. Once the 12 V is taken away from the RESET pin, all the previously protected sectors will be protected
again. Refer to “Temporary Sector Unprotection Timing Diagram” in s TIMING DIAGRAM and “Temporary Sector
Unprotection Algorithm” in s FLOW CHART.
相关PDF资料 |
PDF描述 |
|---|---|
| MBR-2051-1B5T | 51 CONTACT(S), MALE, D MICROMINIATURE CONNECTOR, SOLDER, PLUG |
| MBR-2069-0A1T | 69 CONTACT(S), MALE, D MICROMINIATURE CONNECTOR, SOLDER, PLUG |
| MBR-2069-0A2T | 69 CONTACT(S), MALE, D MICROMINIATURE CONNECTOR, SOLDER, PLUG |
| MBR-2069-0A3T | 69 CONTACT(S), MALE, D MICROMINIATURE CONNECTOR, SOLDER, PLUG |
| MBR-2069-0A4T | 69 CONTACT(S), MALE, D MICROMINIATURE CONNECTOR, SOLDER, PLUG |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MBM29F800TA-70PFTN-SFL(E1) | 制造商:Fujitsu 功能描述: |
| MBM29F800TA-70PFTN-SFLE1 | 制造商:Spansion 功能描述:IC 5V 8M FLASH |
| MBM29F800TA-70PFTR | 制造商:FUJITSU 制造商全称:Fujitsu Component Limited. 功能描述:8M (1M X 8/512K X 16) BIT |
| MBM29F800TA-90 | 制造商:FUJITSU 制造商全称:Fujitsu Component Limited. 功能描述:8M (1M X 8/512K X 16) BIT |
| MBM29F800TA-90PF | 制造商:FUJITSU 制造商全称:Fujitsu Component Limited. 功能描述:8M (1M X 8/512K X 16) BIT |
发布紧急采购，3分钟左右您将得到回复。