参数资料
型号: MC56F8356VFVE
厂商: FREESCALE SEMICONDUCTOR INC
元件分类: 数字信号处理
英文描述: 16-BIT, 120 MHz, OTHER DSP, PQFP144
封装: ROHS COMPLIANT, LQFP-144
文件页数: 17/178页
文件大小: 910K
代理商: MC56F8356VFVE
Register Descriptions
56F8356 Technical Data, Rev. 13
Freescale Semiconductor
113
Preliminary
6.5.1.2
EMI_MODE (EMI_MODE)—Bit 6
This bit reflects the current (non-clocked) state of the EMI_MODE pin. During reset, this bit, coupled with
the EXTBOOT signal, is used to initialize address bits [19:16] either as GPIO or as address. These settings
can be explicitly overwritten using the appropriate GPIO peripheral enable register at any time after reset.
In addition, this pin can be used as a general purpose input pin after reset.
0 = External address bits [19:16] are initially programmed as GPIO
1 = When booted with EXTBOOT = 1, A[19:16] are initially programmed as address. If EXTBOOT is 0,
they are initialized as GPIO.
6.5.1.3
OnCE Enable (OnCE EBL)—Bit 5
0 = OnCE clock to 56800E core enabled when core TAP is enabled
1 = OnCE clock to 56800E core is always enabled
6.5.1.4
Software Reset (SW RST)—Bit 4
This bit is always read as 0. Writing a 1 to this bit will cause the part to reset.
6.5.1.5
Stop Disable (STOP_DISABLE)—Bits 3–2
00 - Stop mode will be entered when the 56800E core executes a STOP instruction
01 - The 56800E STOP instruction will not cause entry into Stop mode; STOP_DISABLE can be
reprogrammed in the future
10 - The 56800E STOP instruction will not cause entry into Stop mode; STOP_DISABLE can then only be
changed by resetting the device
11 - Same operation as 10
6.5.1.6
Wait Disable (WAIT_DISABLE)—Bits 1–0
00 - Wait mode will be entered when the 56800E core executes a WAIT instruction
01 - The 56800E WAIT instruction will not cause entry into Wait mode; WAIT_DISABLE can be
reprogrammed in the future
10 - The 56800E WAIT instruction will not cause entry into Wait mode; WAIT_DISABLE can then only be
changed by resetting the device
11 - Same operation as 10
6.5.2
SIM Reset Status Register (SIM_RSTSTS)
Bits in this register are set upon any system reset and are initialized only by a Power-On Reset (POR). A
reset (other than POR) will only set bits in the register; bits are not cleared. Only software should clear this
register.
相关PDF资料
PDF描述
MPC8272VRPIEX 32-BIT, 300 MHz, RISC PROCESSOR, PBGA516
MC9S12HA64VLLR 16-BIT, FLASH, 32 MHz, MICROCONTROLLER, PQFP100
MC908QB8MDTE 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PDSO16
MC56F8122VFAE 0-BIT, 80 MHz, OTHER DSP, PQFP48
MC908GR32AMFJR2 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PQFP32
相关代理商/技术参数
参数描述
MC56F8357 制造商:未知厂家 制造商全称:未知厂家 功能描述:16-BIT HYBRID CONTROLLERS
MC56F8357EVM 功能描述:KIT EVALUATION FOR MC56F8357 RoHS:否 类别:编程器,开发系统 >> 过时/停产零件编号 系列:- 标准包装:1 系列:- 传感器类型:CMOS 成像,彩色(RGB) 传感范围:WVGA 接口:I²C 灵敏度:60 fps 电源电压:5.7 V ~ 6.3 V 嵌入式:否 已供物品:成像器板 已用 IC / 零件:KAC-00401 相关产品:4H2099-ND - SENSOR IMAGE WVGA COLOR 48-PQFP4H2094-ND - SENSOR IMAGE WVGA MONO 48-PQFP
MC56F8357MPY60 制造商:MOTOROLA 制造商全称:Motorola, Inc 功能描述:16-bit Digital Signal Processor
MC56F8357MPYE 功能描述:数字信号处理器和控制器 - DSP, DSC 16 BIT HYBRID CONTROLLER RoHS:否 制造商:Microchip Technology 核心:dsPIC 数据总线宽度:16 bit 程序存储器大小:16 KB 数据 RAM 大小:2 KB 最大时钟频率:40 MHz 可编程输入/输出端数量:35 定时器数量:3 设备每秒兆指令数:50 MIPs 工作电源电压:3.3 V 最大工作温度:+ 85 C 封装 / 箱体:TQFP-44 安装风格:SMD/SMT
MC56F8357VPY60 制造商:MOTOROLA 制造商全称:Motorola, Inc 功能描述:16-bit Digital Signal Processor