参数资料
型号: MC68HC705CL16
厂商: FREESCALE SEMICONDUCTOR INC
元件分类: 微控制器/微处理器
英文描述: 8-BIT, OTPROM, 1.802 MHz, MICROCONTROLLER, PQFP100
封装: TQFP-100
文件页数: 75/145页
文件大小: 673K
代理商: MC68HC705CL16
June 11, 1997
GENERAL RELEASE SPECIFICATION
MC68HC05CL48
INTERRUPTS
MOTOROLA
REV 2.0
4-3
4.1
RESET INTERRUPT SEQUENCE
The RESET function is not in the strictest sense an interrupt; however, it is acted
upon in a similar manner as shown in Figure 4-1. A low level input on the RESET
pin or internal generated reset signal causes the program to vector to its starting
address which is specied by the contents of memory locations $FFFE and
$FFFF. The I-bit in the condition code register is also set. The MCU is congured
to a known state during this type of reset as described in Section 5.
4.2
SOFTWARE INTERRUPT (SWI)
The SWI is an executable instruction and a non-maskable interrupt since it is
executed regardless of the state of the I-bit in the CCR. If the I-bit is zero
(interrupts enabled), the SWI instruction executes after interrupts which were
pending before the SWI was fetched, or before interrupts if interrupts were
generated after the SWI was fetched. The interrupt service routine address is
specied by the contents of memory locations $FFFC and $FFFD.
4.3
HARDWARE INTERRUPTS
All hardware interrupts except RESET are maskable by the I-bit in the CCR. If the
I-bit is set, all hardware interrupts (internal and external) are disabled. Clearing
the I-bit enables the hardware interrupts. There are six types of hardware
interrupts which are explained in the following sections.
4.3.1 External Interrupt (IRQ)
If the IRQ option is both level and edge sensitive triggering (INTO=0), a low level
or an negative edge at the IRQ pin and the interrupt mask bit of the condition code
register is cleared will cause an EXTERNAL Interrupt to occur. If the MCU has
nished with the interrupt service routine, but the IRQ pin is still low, the
EXTERNAL Interrupt will start again. In fact, the MCU will keep on servicing the
EXTERNAL Interrupt as long as the IRQ pin is low. If the IRQ pin goes low for a
while and resumes to high (a negative pulse) before the interrupt mask bit is
cleared, the MCU will not recognize there was an interrupt request, and no
interrupt will occur after the interrupt mask bit is cleared, i.e. there is no latch for
the interrupt signal for the level sensitive triggering.
If the IRQ option is negative edge sensitive triggering (INTO=1), a negative edge
occurs at the IRQ pin and the interrupt mask bit of the condition code register is
cleared will cause an EXTERNAL Interrupt to occur. If the MCU has nished with
the interrupt service routine, but the IRQ pin has not resumed back to high, no
further interrupt will be generated. The interrupt logic recognizes negative edge
transitions and pulses (special case of negative edges) only. If the negative edge
occurs during the interrupt mask bit is set, the interrupt signal will be latched, an
相关PDF资料
PDF描述
MC68HC705MC4VDW 8-BIT, OTPROM, 3 MHz, MICROCONTROLLER, PDSO28
MSP430F2002TRSA 16-BIT, FLASH, 16 MHz, RISC MICROCONTROLLER, PQCC16
MPC8280CZUSLDX 32-BIT, 375 MHz, RISC PROCESSOR, PBGA480
MPC8270CZQUPEX 32-BIT, 450 MHz, RISC PROCESSOR, PBGA516
MPC8270ZQQLDX 32-BIT, 333 MHz, RISC PROCESSOR, PBGA516
相关代理商/技术参数
参数描述
MC68HC705E6CDW 制造商:Motorola Inc 功能描述: 制造商:MOTOROLA 功能描述:
MC68HC705G1B 制造商:Rochester Electronics LLC 功能描述:- Bulk
MC68HC705J1A 制造商:Freescale Semiconductor 功能描述:
MC68HC705J1ACDW 功能描述:IC MCU 4MHZ 1.2K OTP 20-SOIC RoHS:否 类别:集成电路 (IC) >> 嵌入式 - 微控制器, 系列:HC05 其它有关文件:STM32F101T8 View All Specifications 特色产品:STM32 32-bit Cortex MCUs 标准包装:490 系列:STM32 F1 核心处理器:ARM? Cortex?-M3 芯体尺寸:32-位 速度:36MHz 连通性:I²C,IrDA,LIN,SPI,UART/USART 外围设备:DMA,PDR,POR,PVD,PWM,温度传感器,WDT 输入/输出数:26 程序存储器容量:64KB(64K x 8) 程序存储器类型:闪存 EEPROM 大小:- RAM 容量:10K x 8 电压 - 电源 (Vcc/Vdd):2 V ~ 3.6 V 数据转换器:A/D 10x12b 振荡器型:内部 工作温度:-40°C ~ 85°C 封装/外壳:36-VFQFN,36-VFQFPN 包装:托盘 配用:497-10030-ND - STARTER KIT FOR STM32497-8853-ND - BOARD DEMO STM32 UNIV USB-UUSCIKSDKSTM32-PL-ND - KIT IAR KICKSTART STM32 CORTEXM3497-8512-ND - KIT STARTER FOR STM32F10XE MCU497-8505-ND - KIT STARTER FOR STM32F10XE MCU497-8304-ND - KIT STM32 MOTOR DRIVER BLDC497-6438-ND - BOARD EVALUTION FOR STM32 512K497-6289-ND - KIT PERFORMANCE STICK FOR STM32MCBSTM32UME-ND - BOARD EVAL MCBSTM32 + ULINK-MEMCBSTM32U-ND - BOARD EVAL MCBSTM32 + ULINK2更多... 其它名称:497-9032STM32F101T8U6-ND
MC68HC705J1ACP 功能描述:IC MCU 4MHZ 1.2K OTP 20-DIP RoHS:否 类别:集成电路 (IC) >> 嵌入式 - 微控制器, 系列:HC05 其它有关文件:STM32F101T8 View All Specifications 特色产品:STM32 32-bit Cortex MCUs 标准包装:490 系列:STM32 F1 核心处理器:ARM? Cortex?-M3 芯体尺寸:32-位 速度:36MHz 连通性:I²C,IrDA,LIN,SPI,UART/USART 外围设备:DMA,PDR,POR,PVD,PWM,温度传感器,WDT 输入/输出数:26 程序存储器容量:64KB(64K x 8) 程序存储器类型:闪存 EEPROM 大小:- RAM 容量:10K x 8 电压 - 电源 (Vcc/Vdd):2 V ~ 3.6 V 数据转换器:A/D 10x12b 振荡器型:内部 工作温度:-40°C ~ 85°C 封装/外壳:36-VFQFN,36-VFQFPN 包装:托盘 配用:497-10030-ND - STARTER KIT FOR STM32497-8853-ND - BOARD DEMO STM32 UNIV USB-UUSCIKSDKSTM32-PL-ND - KIT IAR KICKSTART STM32 CORTEXM3497-8512-ND - KIT STARTER FOR STM32F10XE MCU497-8505-ND - KIT STARTER FOR STM32F10XE MCU497-8304-ND - KIT STM32 MOTOR DRIVER BLDC497-6438-ND - BOARD EVALUTION FOR STM32 512K497-6289-ND - KIT PERFORMANCE STICK FOR STM32MCBSTM32UME-ND - BOARD EVAL MCBSTM32 + ULINK-MEMCBSTM32U-ND - BOARD EVAL MCBSTM32 + ULINK2更多... 其它名称:497-9032STM32F101T8U6-ND