参数资料
型号: MC68HC705P6ACP
厂商: FREESCALE SEMICONDUCTOR INC
元件分类: 微控制器/微处理器
英文描述: 8-BIT, OTPROM, 2.1 MHz, MICROCONTROLLER, PDIP28
封装: PLASTIC, DIP-28
文件页数: 27/98页
文件大小: 532K
代理商: MC68HC705P6ACP
MC68HC705P6A Advance Information Data Sheet, Rev. 2.1
Freescale Semiconductor
33
Chapter 5
Interrupts
5.1 Introduction
The MCU can be interrupted six different ways:
1.
Non-maskable software interrupt instruction (SWI)
2.
External asynchronous interrupt (IRQ)
3.
Input capture interrupt (TIMER)
4.
Output compare interrupt (TIMER)
5.
Timer overflow interrupt (TIMER)
6.
Port A interrupt (if selected via mask option register)
Interrupts cause the processor to save the register contents on the stack and to set the interrupt mask (I
bit) to prevent additional interrupts. Unlike reset, hardware interrupts do not cause the current instruction
execution to be halted, but are considered pending until the current instruction is completed.
When the current instruction is completed, the processor checks all pending hardware interrupts. If
interrupts are not masked (I bit in the condition code register is clear) and the corresponding interrupt
enable bit is set, the processor proceeds with interrupt processing. Otherwise, the next instruction is
fetched and executed. The SWI is executed the same as any other instruction, regardless of the I-bit state.
When an interrupt is to be processed, the CPU puts the register contents on the stack, sets the I bit in the
CCR, and fetches the address of the corresponding interrupt service routine from the vector table at
locations $1FF8 through $1FFF. If more than one interrupt is pending when the interrupt vector is fetched,
the interrupt with the highest vector location shown in Table 5-1 will be serviced first.
An RTI instruction is used to signify when the interrupt software service routine is completed. The RTI
instruction causes the CPU state to be recovered from the stack and normal processing to resume at the
next instruction that was to be executed when the interrupt took place. Figure 5-1 shows the sequence of
events that occurs during interrupt processing.
Table 5-1. Vector Addresses for Interrupts and Reset
Register
Flag
Name
Interrupts
CPU
Interrupt
Vector
Address
N/A
Reset
RESET
$1FFE–$1FFF
N/A
Software
SWI
$1FFC–$1FFD
N/A
External Interrupt
IRQ
$1FFA–$1FFB
TSR
ICF
Timer Input Capture
TIMER
$1FF8–$1FF9
TSR
OCF
Timer Output Compare
TIMER
$1FF8–$1FF9
TSR
TOF
Timer Overflow
TIMER
$1FF8–$1FF9
相关PDF资料
PDF描述
MC908GR60AMFU 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PQFP64
MC908GR60AVFU 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PQFP64
MC9S12DG128BCFU 16-BIT, FLASH, 25 MHz, MICROCONTROLLER, PQFP80
MPE603EFE133TX 32-BIT, 133.33 MHz, RISC PROCESSOR, CQFP240
MPE603ERX100TX 32-BIT, 100 MHz, RISC PROCESSOR, CBGA255
相关代理商/技术参数
参数描述
MC68HC705P6ADW 制造商:Rochester Electronics LLC 功能描述:MCU, 176 BYTES RAM, A/D - Bulk
MC68HC705P6AMDW 功能描述:IC MCU 4.6K OTP 2.1MHZ 28-SOIC RoHS:否 类别:集成电路 (IC) >> 嵌入式 - 微控制器, 系列:HC05 标准包装:250 系列:56F8xxx 核心处理器:56800E 芯体尺寸:16-位 速度:60MHz 连通性:CAN,SCI,SPI 外围设备:POR,PWM,温度传感器,WDT 输入/输出数:21 程序存储器容量:40KB(20K x 16) 程序存储器类型:闪存 EEPROM 大小:- RAM 容量:6K x 16 电压 - 电源 (Vcc/Vdd):2.25 V ~ 3.6 V 数据转换器:A/D 6x12b 振荡器型:内部 工作温度:-40°C ~ 125°C 封装/外壳:48-LQFP 包装:托盘 配用:MC56F8323EVME-ND - BOARD EVALUATION MC56F8323
MC68HC705P6AMP 制造商:Rochester Electronics LLC 功能描述:- Bulk
MC68HC705P6CDW 制造商:Motorola Inc 功能描述:
MC68HC705P6CP 制造商:Freescale Semiconductor 功能描述: 制造商:Motorola Inc 功能描述: