- 您现在的位置：买卖IC网 > PDF目录80397 > MC68HC705P6ACP (FREESCALE SEMICONDUCTOR INC) 8-BIT, OTPROM, 2.1 MHz, MICROCONTROLLER, PDIP28 PDF资料下载
参数资料
| 型号： | MC68HC705P6ACP |
| 厂商： | FREESCALE SEMICONDUCTOR INC |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 8-BIT, OTPROM, 2.1 MHz, MICROCONTROLLER, PDIP28 |
| 封装： | PLASTIC, DIP-28 |
| 文件页数： | 29/98页 |
| 文件大小： | 532K |
| 代理商： | MC68HC705P6ACP |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页当前第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页
Interrupt Types
MC68HC705P6A Advance Information Data Sheet, Rev. 2.1
Freescale Semiconductor
35
5.2 Interrupt Types
The interrupts fall into three categories: reset, software, and hardware.
5.2.1 Reset Interrupt Sequence
The reset function is not in the strictest sense an interrupt; however, it is acted upon in a similar manner
as shown in Figure 5-1. A low-level input on the RESET pin or internally generated RST signal causes
the program to vector to its starting address which is specified by the contents of memory locations $1FFE
and $1FFF. The I bit in the condition code register is also set. The MCU is configured to a known state
during this type of reset as previously described in Chapter 4 Resets.
5.2.2 Software Interrupt (SWI)
The SWI is an executable instruction. It is also a non-maskable interrupt since it is executed regardless
of the state of the I bit in the CCR. As with any instruction, interrupts pending during the previous
instruction will be serviced before the SWI opcode is fetched. The interrupt service routine address for the
SWI instruction is specified by the contents of memory locations $1FFC and $1FFD.
5.2.3 Hardware Interrupts
All hardware interrupts are maskable by the I bit in the CCR. If the I bit is set, all hardware interrupts
(internal and external) are disabled. Clearing the I bit enables the hardware interrupts. Four hardware
interrupts are explained in the following subsections.
5.2.3.1 External Interrupt (IRQ)
The IRQ/VPP pin drives an asynchronous interrupt to the CPU. An edge detector flip-flop is latched on the
falling edge of IRQ/VPP. If either the output from the internal edge detector flip-flop or the level on the
IRQ/VPP pin is low, a request is synchronized to the CPU to generate the IRQ interrupt. If the LEVEL bit
in the mask option register is clear (edge-sensitive only), the output of the internal edge detector flip-flop
is sampled and the input level on the IRQ/VPP pin is ignored. The interrupt service routine address is
specified by the contents of memory locations $1FFA and $1FFB. If the port A interrupts are enabled by
the MOR, they generate external interrupts identically to the IRQ/VPP pin.
NOTE
The internal interrupt latch is cleared nine internal clock cycles after the
interrupt is recognized (immediately after location $1FFA is read).
Therefore, another external interrupt pulse could be latched during the IRQ
service routine.
Another interrupt will be serviced if the IRQ pin is still in a low state when
the RTI in the service routine is executed.
5.2.3.2 Input Capture Interrupt
The input capture interrupt is generated by the 16-bit timer as described in Chapter 8 Capture/Compare
Timer. The input capture interrupt flag is located in register TSR and its corresponding enable bit can be
found in register TCR. The I bit in the CCR must be clear for the input capture interrupt to be enabled. The
interrupt service routine address is specified by the contents of memory locations $1FF8 and $1FF9.
相关PDF资料 |
PDF描述 |
|---|---|
| MC908GR60AMFU | 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PQFP64 |
| MC908GR60AVFU | 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PQFP64 |
| MC9S12DG128BCFU | 16-BIT, FLASH, 25 MHz, MICROCONTROLLER, PQFP80 |
| MPE603EFE133TX | 32-BIT, 133.33 MHz, RISC PROCESSOR, CQFP240 |
| MPE603ERX100TX | 32-BIT, 100 MHz, RISC PROCESSOR, CBGA255 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MC68HC705P6ADW | 制造商:Rochester Electronics LLC 功能描述:MCU, 176 BYTES RAM, A/D - Bulk |
| MC68HC705P6AMDW | 功能描述:IC MCU 4.6K OTP 2.1MHZ 28-SOIC RoHS:否 类别:集成电路 (IC) >> 嵌入式 - 微控制器， 系列:HC05 标准包装:250 系列:56F8xxx 核心处理器:56800E 芯体尺寸:16-位 速度:60MHz 连通性:CAN，SCI，SPI 外围设备:POR，PWM，温度传感器，WDT 输入/输出数:21 程序存储器容量:40KB（20K x 16） 程序存储器类型:闪存 EEPROM 大小:- RAM 容量:6K x 16 电压 - 电源 (Vcc/Vdd):2.25 V ~ 3.6 V 数据转换器:A/D 6x12b 振荡器型:内部 工作温度:-40°C ~ 125°C 封装/外壳:48-LQFP 包装:托盘 配用:MC56F8323EVME-ND - BOARD EVALUATION MC56F8323 |
| MC68HC705P6AMP | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| MC68HC705P6CDW | 制造商:Motorola Inc 功能描述: |
| MC68HC705P6CP | 制造商:Freescale Semiconductor 功能描述: 制造商:Motorola Inc 功能描述: |
发布紧急采购，3分钟左右您将得到回复。