- 您现在的位置：买卖IC网 > PDF目录201871 > MC68HC912BL16FU8 (FREESCALE SEMICONDUCTOR INC) 16-BIT, FLASH, 8 MHz, MICROCONTROLLER, PQFP64 PDF资料下载
参数资料
| 型号： | MC68HC912BL16FU8 |
| 厂商： | FREESCALE SEMICONDUCTOR INC |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 16-BIT, FLASH, 8 MHz, MICROCONTROLLER, PQFP64 |
| 封装： | QFP-64 |
| 文件页数： | 81/128页 |
| 文件大小： | 3326K |
| 代理商： | MC68HC912BL16FU8 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页当前第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页
MC68HC912BL16
56
MC68HC912BL16TS/D
To give a maskable interrupt source highest priority, write the low byte of the vector address to the
HPRIO register. For example, writing $F0 to HPRIO would assign highest maskable interrupt priority to
the real-time interrupt timer ($FFF0). If an unimplemented vector address or a non-I-masked vector ad-
dress (value higher than $F2) is written, then IRQ will be the default highest priority interrupt.
9.4 Resets
There are four possible sources of reset. Power-on reset (POR), and external reset on the RESET pin
share the normal reset vector. The computer operating properly (COP) reset and the clock monitor reset
each has a vector. Entry into reset is asynchronous and does not require a clock but the MCU cannot
sequence out of reset without a system clock.
9.4.1 Power-On Reset
A positive transition on VDD causes a power-on reset (POR). An external voltage level detector, or other
external reset circuits, are the usual source of reset in a system. The POR circuit only initializes internal
circuitry during cold starts and cannot be used to force a reset as system voltage drops.
9.4.2 External Reset
The CPU distinguishes between internal and external reset conditions by sensing whether the reset pin
rises to a logic one in less than eight E-clock cycles after an internal device releases reset. When a reset
condition is sensed, the RESET pin is driven low by an internal device for about 16 E-clock cycles, then
released. Eight E-clock cycles later it is sampled. If the pin is still held low, the CPU assumes that an
external reset has occurred. If the pin is high, it indicates that the reset was initiated internally by either
the COP system or the clock monitor.
To prevent a COP or clock monitor reset from being detected during an external reset, hold the reset
pin low for at least 32 cycles. An external RC power-up delay circuit on the reset pin is not recommended
— circuit charge time can cause the MCU to misinterpret the type of reset that has occurred.
9.4.3 COP Reset
The MCU includes a computer operating properly (COP) system to help protect against software fail-
ures. When COP is enabled, software must write $55 and $AA (in this order) to the COPRST register
in order to keep a watchdog timer from timing out. Other instructions may be executed between these
writes. A write of any value other than $55 or $AA or software failing to execute the sequence properly
causes a COP reset to occur.
9.4.4 Clock Monitor Reset
If clock frequency falls below a predetermined limit when the clock monitor is enabled, a reset occurs.
9.5 Effects of Reset
When a reset occurs, MCU registers and control bits are changed to known start-up states, as follows.
9.5.1 Operating Mode and Memory Map
Operating mode and default memory mapping are determined by the states of the BKGD, MODA, and
MODB pins during reset. The SMODN, MODA, and MODB bits in the MODE register reflect the status
of the mode-select inputs at the rising edge of reset. Operating mode and default maps can subsequent-
ly be changed according to strictly defined rules.
9.5.2 Clock and Watchdog Control Logic
The COP watchdog system is enabled, with the CR[2:0] bits set for the shortest duration time-out. The
clock monitor is disabled. The RTIF flag is cleared and automatic hardware interrupts are masked. The
rate control bits are cleared, and must be initialized before the RTI system is used. The DLY control bit
is set to specify an oscillator start-up delay upon recovery from STOP mode.
F
re
e
sc
a
le
S
e
m
ic
o
n
d
u
c
to
r,
I
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
n
c
..
.
相关PDF资料 |
PDF描述 |
|---|---|
| MC68HC912BL16VFU8 | 16-BIT, FLASH, 8 MHz, MICROCONTROLLER, PQFP64 |
| MK74CG117AFT | 90 MHz, OTHER CLOCK GENERATOR, PDSO48 |
| MC68HC08AS32ACFU | 8-BIT, MROM, 8.4 MHz, MICROCONTROLLER, PQFP64 |
| MC68HRC98JL3ECFA | 8-BIT, FLASH, 4 MHz, MICROCONTROLLER, PQFP48 |
| MC68HRC98JL3EMDW | 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PDSO28 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MC68HC916P1CAA16 | 功能描述:16位微控制器 - MCU 16B MCU 32K FLASH RoHS:否 制造商:Texas Instruments 核心:RISC 处理器系列:MSP430FR572x 数据总线宽度:16 bit 最大时钟频率:24 MHz 程序存储器大小:8 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:2 V to 3.6 V 工作温度范围:- 40 C to + 85 C 封装 / 箱体:VQFN-40 安装风格:SMD/SMT |
| MC68HC916P1CFU16 | 制造商:Rochester Electronics LLC 功能描述:16BIT W/32KB FLASH EEPRO - Bulk |
| MC68HC916P1VAA16 | 功能描述:IC MCU 32K FLASH 16MHZ 80-QFP RoHS:是 类别:集成电路 (IC) >> 嵌入式 - 微控制器， 系列:HC16 标准包装:1 系列:AVR® ATmega 核心处理器:AVR 芯体尺寸:8-位 速度:16MHz 连通性:I²C，SPI，UART/USART 外围设备:欠压检测/复位，POR，PWM，WDT 输入/输出数:32 程序存储器容量:32KB（16K x 16） 程序存储器类型:闪存 EEPROM 大小:1K x 8 RAM 容量:2K x 8 电压 - 电源 (Vcc/Vdd):2.7 V ~ 5.5 V 数据转换器:A/D 8x10b 振荡器型:内部 工作温度:-40°C ~ 125°C 封装/外壳:44-TQFP 包装:剪切带 (CT) 其它名称:ATMEGA324P-B15AZCT |
| MC68HC916P3CFU16 | 制造商:Rochester Electronics LLC 功能描述:16BIT MCU FOR GENERAL - Bulk |
| MC68HC98LJ12CFU | 制造商:Rochester Electronics LLC 功能描述: 制造商:Freescale Semiconductor 功能描述: |
发布紧急采购，3分钟左右您将得到回复。