- 您现在的位置：买卖IC网 > PDF目录3972 > MC7448VU867NC (Freescale Semiconductor)IC MPU RISC 32BIT 360-FCCBGA PDF资料下载
参数资料
| 型号： | MC7448VU867NC |
| 厂商： | Freescale Semiconductor |
| 文件页数： | 36/60页 |
| 文件大小： | 0K |
| 描述： | IC MPU RISC 32BIT 360-FCCBGA |
| 标准包装： | 44 |
| 系列： | MPC74xx |
| 处理器类型： | 32-位 MPC74xx PowerPC |
| 速度： | 867MHz |
| 电压： | 1V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 360-CBGA，FCCBGA |
| 供应商设备封装： | 360-FCCBGA（25x25） |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页当前第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页
MPC7448 RISC Microprocessor Hardware Specifications, Rev. 4
Freescale Semiconductor
41
System Design Information
9.2.4
Decoupling Recommendations
Due to the MPC7448 dynamic power management feature, large address and data buses, and high
operating frequencies, the MPC7448 can generate transient power surges and high frequency noise in its
power supply, especially while driving large capacitive loads. This noise must be prevented from reaching
other components in the MPC7448 system, and the MPC7448 itself requires a clean, tightly regulated
source of power. Therefore, it is recommended that the system designer use sufficient decoupling
capacitors, typically one capacitor for every VDD pin, and a similar amount for the OVDD pins, placed as
close as possible to the power pins of the MPC7448. It is also recommended that these decoupling
capacitors receive their power from separate VDD, OVDD, and GND power planes in the PCB, using short
traces to minimize inductance.
These capacitors should have a value of 0.01 or 0.1 F. Only ceramic surface mount technology (SMT)
capacitors should be used to minimize lead inductance. Orientations where connections are made along
the length of the part, such as 0204, are preferable but not mandatory. Consistent with the
recommendations of Dr. Howard Johnson in High Speed Digital Design: A Handbook of Black Magic
(Prentice Hall, 1993) and contrary to previous recommendations for decoupling Freescale
microprocessors, multiple small capacitors of equal value are recommended over using multiple values of
capacitance.
In addition, it is recommended that there be several bulk storage capacitors distributed around the PCB,
feeding the VDD and OVDD planes, to enable quick recharging of the smaller chip capacitors. These bulk
capacitors should have a low equivalent series resistance (ESR) rating to ensure the quick response time
necessary. They should also be connected to the power and ground planes through two vias to minimize
inductance. Suggested bulk capacitors are 100–330 F (AVX TPS tantalum or Sanyo OSCON).
9.3
Connection Recommendations
To ensure reliable operation, it is highly recommended to connect unused inputs to an appropriate signal
level. Unless otherwise noted, unused active low inputs should be tied to OVDD and unused active high
inputs should be connected to GND. All NC (no connect) signals must remain unconnected.
Power and ground connections must be made to all external VDD, OVDD, and GND pins in the MPC7448.
For backward compatibility with the MPC7447, MPC7445, and MP7441, or for migrating a system
originally designed for one of these devices to the MPC7448, the new power and ground signals (formerly
NC, see Table 11) may be left unconnected if the core frequency is 1 GHz or less. Operation above 1 GHz
requires that these additional power and ground signals be connected, and it is strongly recommended that
all new designs include the additional connections. See also Section 7, “Pinout Listings,” for additional
information.
The MPC7448 provides VDD_SENSE, OVDD_SENSE, and GND_SENSE pins. These pins connect
directly to the power/ground planes in the device package and are intended to allow an external device to
measure the voltage present on the VDD, OVDD and GND planes in the device package. The most common
use for these signals is as a feedback signal to a power supply regulator to allow it to compensate for board
losses and supply the correct voltage at the device. (Note that all voltage parameters are specified at the
pins of the device.) If not used for this purpose, it is recommended that these signals be connected to test
points that can be used in the event that an accurate measurement of the voltage at the device is needed
during system debug. Otherwise, these signals should be connected to the appropriate power/ground
planes on the circuit board or left unconnected.
相关PDF资料 |
PDF描述 |
|---|---|
| MC7448VU667NC | IC MPU RISC 32BIT 360-FCCBGA |
| MC7448VU600NC | IC MPU RISC 32BIT 360-FCCBGA |
| MC7448VU1700LC | IC MPU RISC 32BIT 360-FCCBGA |
| FMM36DREI | CONN EDGECARD 72POS .156 EYELET |
| HSC60DTEF | CONN EDGECARD 120POS .100 EYELET |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MC7448VU867ND | 功能描述:微处理器 - MPU APL8 RV2.2.1 1.0V 105C RoHS:否 制造商:Atmel 处理器系列:SAMA5D31 核心:ARM Cortex A5 数据总线宽度:32 bit 最大时钟频率:536 MHz 程序存储器大小:32 KB 数据 RAM 大小:128 KB 接口类型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作电源电压:1.8 V to 3.3 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:FBGA-324 |
| MC7455_1102476 | 功能描述:4G LTE FB 3G HSPA+ GNSS NAM&EMEA 制造商:sierra wireless 系列:* 包装:剪切带（CT） 零件状态:在售 安装类型:卡边 封装/外壳:模块 标准包装:100 |
| MC7455_1103578 | 功能描述:4G LTE FB 3G HSPA+ GNSS NAM&EMEA 制造商:sierra wireless 系列:MC 零件状态:在售 功能:调制解调器 调制或协议:Beidou，Galileo，GLONASS，GPS，LTE，WCDMA 应用:通用 接口:USB 灵敏度:- 功率 - 输出:- 数据速率（最大值）:300Mbps 特性:- 电压 - 电源:- 标准包装:100 |
| MC7455ARX1000LF | 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:RISC Microprocessor Hardware Specifications |
| MC7455ARX1000LG | 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:RISC Microprocessor Hardware Specifications |
发布紧急采购，3分钟左右您将得到回复。