- 您现在的位置：买卖IC网 > PDF目录4033 > MC7457RX1000NC (Freescale Semiconductor)IC MPU RISC 32BIT 483FCCBGA PDF资料下载
参数资料
| 型号： | MC7457RX1000NC |
| 厂商： | Freescale Semiconductor |
| 文件页数： | 17/71页 |
| 文件大小： | 0K |
| 描述： | IC MPU RISC 32BIT 483FCCBGA |
| 标准包装： | 36 |
| 系列： | MPC74xx |
| 处理器类型： | 32-位 MPC74xx PowerPC |
| 速度： | 1.0GHz |
| 电压： | 1.1V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 483-BCBGA，FCCBGA |
| 供应商设备封装： | 483-FCCBGA（29x29） |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页当前第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页
MPC7457 RISC Microprocessor Hardware Specifications, Rev. 8
Electrical and Thermal Characteristics
Freescale Semiconductor
24
5.2.4
L3 Bus AC Specifications
The MPC7457 L3 interface supports three different types of SRAM: source-synchronous, double data rate
(DDR) MSUG2 SRAM, Late Write SRAMs, and pipeline burst (PB2) SRAMs. Each requires a different
protocol on the L3 interface and a different routing of the L3 clock signals. The type of SRAM is
programmed in L3CR[22:23] and the MPC7457 then follows the appropriate protocol for that type. The
designer must connect and route the L3 signals appropriately for each type of SRAM. Following are some
observations about the L3 interface.
The routing for the point-to-point signals (L3_CLK[0:1], L3DATA[0:63], L3DP[0:7], and
L3_ECHO_CLK[0:3]) to a particular SRAM must be delay matched.
For 1-Mbyte of SRAM, use L3_ADDR[16:0] (L3_ADDR[0] is LSB)
For 2-Mbyte of SRAM, use L3_ADDR[17:0] (L3_ADDR[0] is LSB)
For 4-Mbyte of SRAM, use L3_ADDR[18:0] (L3_ADDR[0] is LSB)
No pull-up resistors are required for the L3 interface
For high-speed operations, L3 interface address and control signals should be a ‘T’ with minimal
stubs to the two loads; data and clock signals should be point-to-point to their single load. Figure 8
shows the AC test load for the L3 interface.
Figure 8. AC Test Load for the L3 Interface
In general, if routing is short, delay-matched, and designed for incident wave reception and minimal
reflection, there is a high probability that the AC timing of the MPC7457 L3 interface will meet the
maximum frequency operation of appropriately chosen SRAMs. This is despite the pessimistic,
guard-banded AC specifications (see Table 12, Table 13, and Table 14), the limitations of functional
testers described in Section 5.2.3, “L3 Clock AC Specifications,” and the uncertainty of clocks and signals
which inevitably make worst-case critical path timing analysis pessimistic.
More specifically, certain signals within groups should be delay-matched with others in the same group
while intergroup routing is less critical. Only the address and control signals are common to both SRAMs
and additional timing margin is available for these signals. The double-clocked data signals are grouped
with individual clocks as shown in Figure 9 or Figure 11, depending on the type of SRAM. For example,
for the MSUG2 DDR SRAM (see Figure 9); L3DATA[0:31], L3DP[0:3], and L3_CLK[0] form a closely
coupled group of outputs from the MPC7457; while L3DATA[0:15], L3DP[0:1], and L3_ECHO_CLK[0]
form a closely coupled group of inputs.
The MPC7450 RISC Microprocessor Family User’s Manual refers to logical settings called ‘sample
points’ used in the synchronization of reads from the receive FIFO. The computation of the correct value
for this setting is system-dependent and is described in the MPC7450 RISC Microprocessor Family User’s
Manual. Three specifications are used in this calculation and are given in Table 11. It is essential that all
three specifications are included in the calculations to determine the sample points, as incorrect settings
can result in errors and unpredictable behavior. For more information, see the MPC7450 RISC
Microprocessor Family User’s Manual.
Output
Z0 = 50 Ω
GVDD/2
RL = 50 Ω
相关PDF资料 |
PDF描述 |
|---|---|
| IDT7025S30J | IC SRAM 128KBIT 30NS 84PLCC |
| XC4020XL-3HT144C | IC FPGA C-TEMP 3.3V 3SPD 144HQFP |
| XC4020XL-3BG256I | IC FPGA I-TEMP 3.3V 3SPD 256PBGA |
| XC4020XL-3BG256C | IC FPGA C-TEMP 3.3V 3SPD 256PBGA |
| IDT70V9269S9PRF8 | IC SRAM 256KBIT 9NS 128TQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MC7457RX1200PB | 制造商:Freescale Semiconductor 功能描述:A7, 1.35V +50MV/-30MV - Trays |
| MC7457RX1267LB | 制造商:Freescale Semiconductor 功能描述:MPC74XX RISC 32-BIT 0.13UM 1.267GHZ 1.5V/1.8V/2.5V 483-PIN F - Trays |
| MC7457RX1267LC | 功能描述:微处理器 - MPU APOLO7 RV1.2 1.3V 105C RoHS:否 制造商:Atmel 处理器系列:SAMA5D31 核心:ARM Cortex A5 数据总线宽度:32 bit 最大时钟频率:536 MHz 程序存储器大小:32 KB 数据 RAM 大小:128 KB 接口类型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作电源电压:1.8 V to 3.3 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:FBGA-324 |
| MC7457RX1333PB | 制造商:Freescale Semiconductor 功能描述:A7, 1.35V +50MV/-30MV - Trays |
| MC7457RX733NC | 功能描述:IC MPU RISC 32BIT 483FCCBGA RoHS:否 类别:集成电路 (IC) >> 嵌入式 - 微处理器 系列:MPC74xx 标准包装:1 系列:MPC85xx 处理器类型:32-位 MPC85xx PowerQUICC III 特点:- 速度:1.2GHz 电压:1.1V 安装类型:表面贴装 封装/外壳:783-BBGA，FCBGA 供应商设备封装:783-FCPBGA（29x29） 包装:托盘 |
发布紧急采购，3分钟左右您将得到回复。