- 您现在的位置：买卖IC网 > PDF目录11944 > MC9RS08KA1CSCR (Freescale Semiconductor)IC MCU 8-BIT 1K FLASH 8-SOIC PDF资料下载
参数资料
| 型号： | MC9RS08KA1CSCR |
| 厂商： | Freescale Semiconductor |
| 文件页数： | 88/136页 |
| 文件大小： | 0K |
| 描述： | IC MCU 8-BIT 1K FLASH 8-SOIC |
| 产品培训模块： | Mechatronics USBSpyder08 Discovery Kit RS08KA2 Low-End Microcontroller Series MC9RS08KA8 Microcontroller |
| 标准包装： | 1 |
| 系列： | RS08 |
| 核心处理器： | RS08 |
| 芯体尺寸： | 8-位 |
| 速度： | 10MHz |
| 外围设备： | LVD，POR，WDT |
| 输入/输出数： | 4 |
| 程序存储器容量： | 1KB（1K x 8） |
| 程序存储器类型： | 闪存 |
| RAM 容量： | 63 x 8 |
| 电压 - 电源 (Vcc/Vdd)： | 1.8 V ~ 5.5 V |
| 振荡器型： | 内部 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 包装： | 标准包装 |
| 产品目录页面： | 726 (CN2011-ZH PDF) |
| 其它名称： | MC9RS08KA1CSCRDKR |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页当前第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页第129页第130页第131页第132页第133页第134页第135页第136页
Chapter 7 Keyboard Interrupt (RS08KBIV1)
MC9RS08KA2 Series Data Sheet, Rev. 4
Freescale Semiconductor
55
7.4
Functional Description
This on-chip peripheral module is called a keyboard interrupt (KBI) module because it was originally
designed to simplify the connection and use of row-column matrices of keyboard switches. However, these
inputs are also useful as extra external interrupt inputs and as an external means of waking the MCU from
stop or wait low-power modes.
The KBI module allows its pins to act as additional interrupt sources. Writing to the KBIPEn bits in the
keyboard interrupt pin enable register (KBIPE) independently enables or disables each KBI pin. Each KBI
pin can be configured as edge sensitive or edge and level sensitive based on the KBMOD bit in the
keyboard interrupt status and control register (KBISC). Edge sensitive can be software programmed to be
either falling or rising; the level can be either low or high. The polarity of the edge or edge and level
sensitivity is selected using the KBEDGn bits in the keyboard interrupt edge select register (KBIES).
Synchronous logic is used to detect edges. Prior to detecting an edge, enabled keyboard inputs must be at
the deasserted logic level. A falling edge is detected when an enabled keyboard input signal is seen as a
logic 1 (the deasserted level) during one bus cycle and then a logic 0 (the asserted level) during the next
cycle. A rising edge is detected when the input signal is seen as a logic 0 during one bus cycle and then a
logic 1 during the next cycle.
7.4.1
Edge Only Sensitivity
A valid edge on an enabled KBI pin will set KBF in KBISC. If KBIE in KBISC is set, an interrupt request
will be presented to the CPU. Clearing of KBF is accomplished by writing a 1 to KBACK in KBISC.
7.4.2
Edge and Level Sensitivity
A valid edge or level on an enabled KBI pin will set KBF in KBISC. If KBIE in KBISC is set, an interrupt
request will be presented to the CPU. Clearing of KBF is accomplished by writing a 1 to KBACK in
KBISC, provided all enabled keyboard inputs are at their deasserted levels. KBF will remain set if any
enabled KBI pin is asserted while attempting to clear by writing a 1 to KBACK.
7.4.3
KBI Pullup/Pulldown Device
The KBI pins does not automatically configure an internal pullup/pulldown device when a KBI pin is
enabled. An internal pull device can be used by configuring the associated I/O port pull device enable
register (PTAPE) and pullup/pulldown control register (PTAPUD).
7.4.4
KBI Initialization
When a keyboard interrupt pin is first enabled, it is possible to get a false keyboard interrupt flag. To
prevent a false interrupt request during keyboard initialization, the user should do the following:
1. Mask keyboard interrupts by clearing KBIE in KBISC.
2. If using internal pullup/pulldown device, configure the associated I/O port pullup/pulldown device.
3. Enable the KBI polarity by setting the appropriate KBEDGn bits in KBIES.
4. Enable the KBI pins by setting the appropriate KBIPEn bits in KBIPE.
相关PDF资料 |
PDF描述 |
|---|---|
| V24A28T400B3 | CONVERTER MOD DC/DC 28V 400W |
| MC9S12HZ64CAA | IC MCU 16BIT 64K FLASH 80-QFP |
| 2-6457567-5 | ADPTR,DUP,LC,SR BEIGE,CER,LOGO |
| V24A28T400B | CONVERTER MOD DC/DC 28V 400W |
| MC908MR8MPE | IC MCU 8BIT 8K FLASH 28-PDIP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MC9RS08KA1DB | 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:Microcontrollers |
| MC9RS08KA1PC | 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:Microcontrollers |
| MC9RS08KA1SC | 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:Microcontrollers |
| MC9RS08KA2 | 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:Microcontrollers |
| MC9RS08KA2_07 | 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:Microcontrollers |
发布紧急采购，3分钟左右您将得到回复。