- 您现在的位置：买卖IC网 > PDF目录16608 > MCZ33800EK (Freescale Semiconductor)IC ENGINE CTRL SW/DVR 54-SOIC PDF资料下载
参数资料
| 型号： | MCZ33800EK |
| 厂商： | Freescale Semiconductor |
| 文件页数： | 21/39页 |
| 文件大小： | 0K |
| 描述： | IC ENGINE CTRL SW/DVR 54-SOIC |
| 标准包装： | 26 |
| 应用： | 自动 |
| 电流 - 电源： | 10mA |
| 电源电压： | 5 V ~ 36 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 54-BSSOP（0.295"，7.50mm 宽）裸露焊盘 |
| 供应商设备封装： | 54-SOICW-EP |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页当前第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页
FUNCTIONAL DEVICE OPERATION
LOGIC COMMANDS AND REGISTERS
? Off State Open Load Detect
? On State Short Circuit Detect
Table 6. Load Resistance Measurement Select
? Programmable Drain Threshold and Timer for Short Fault
Detection
? Load Resistance Measurement
Each pre-driver is capable of detecting an open load in the
off state and shorted load in the on state. All faults are
reported through SPI communication. For open load
detection, a resistor is placed between the drain sense pin
and source sense pin of the IC. An open load fault is reported
when the drain voltage is less than the 2.5V threshold. A
shorted load fault is reported when the drain voltage is
greater than the programmed threshold voltage.
Programming of the drain short fault threshold voltage is
Bits 6 through 9 are used to perform the load resistance
measurement function as described in the Gate Drive On/Off
Command section below.
GATE DRIVE ON/OFF COMMAND
The GD ON/OFF Command provides control bits for two
functions:
? On/Off control of the GDx outputs.
? Load Resistance measurement function.
On/Off control bit 0 through bit 5 control gate drive outputs
GD1 through GD6 respectively. Setting the bit to logic1 will
enable the gate drive to the external MOSFET. Setting the bit
to logic 0 will actively pull the gate to ground.
GD ON/OFF Command bits 6 through 9 control the load
Bits 9876
0000
0001
0010
0011
0100
0101
0110
0111
1000
1001
1010
1011
1100
1101
1110
1111
MUX Select
Normal Operation
V DSNS1 to R EXT , V DSNS2 to Diff-Amp +
V DSNS2 to R EXT , V DSNS1 to Diff-Amp +
V DSNS3 to R EXT , V DSNS4 to Diff-Amp +
V DSNS4 to R EXT , V DSNS3 to Diff-Amp +
V DSNS5 to R EXT , V DSNS6 to Diff-Amp +
V DSNS6 to R EXT , V DSNS5 to Diff-Amp +
Normal Operation
Normal Operation
Normal Operation
V DSNS2 to R EXT , V DSNS1 to Diff-Amp +
V DSNS3 to R EXT , V DSNS1 to Diff-Amp +
V DSNS4 to R EXT , V DSNS1 to Diff-Amp +
V DSNS5 to R EXT , V DSNS1 to Diff-Amp +
V DSNS6 to R EXT , V DSNS1 to Diff-Amp +
Normal Operation
measurement feature. The gate drive pre-drivers are
selected in matched pairs. Selecting a load resistance
measurement disables a specified output pair and performs
the resistance measurement using the defined pair. All other
outputs will operate as programmed. Resistance is measured
by passing a known current through the load and by
measuring the voltage across it. The resistor placed on the
REXT pin determines the current through the load during
measurement. The voltage output on the LRFDBK pin is the
differential load voltage with the defined current through it.
From the two parameters, the load resistance may be
calculated. Table 6 illustrates the load diagnostic multiplex
function.
PWM PIN ENABLE COMMAND
The PWM Pin Enable Command provides control bits for
two functions:
? Enable or Disable of PWM input pins.
? Enable or Disable of the internal PWM controller for GD1
through GD6.
PWM pin Enable bit 0 through bit 5 enable or disable the
PWM1 through PWM6 input pins respectively. A logic 0 in the
SPI word will enable the PWM input pin, while logic 1 in the
SPI word will disable the PWM input pin. Default state is with
the PWM input pin enabled. With the PWM input pin disabled,
the AND/OR function is also disabled and control is achieved
through the Gate Drive ON/OFF command or the internal
PWM controller.
AND /OR COMMAND
The AND/OR Command provides control bits for two
functions:
? Determines AND/OR relation between ON/OFF SPI bit
and PWM input pin.
? Enable or Disable of the internal PWM controller for G1
through GD6.
The AND /OR command describes the condition by which
the PWM input pin controls the output driver. A logic[0] in the
AND / OR register will OR the PWM input pin with the
respective bit in the ON/OFF register. Likewise, a logic[1] in
33800
Analog Integrated Circuit Device Data
Freescale Semiconductor
21
相关PDF资料 |
PDF描述 |
|---|---|
| HSC05DRYI-S13 | CONN EDGECARD 10POS .100 EXTEND |
| ECC22DRYI | CONN EDGECARD 44POS DIP .100 SLD |
| H2MXS-5036G | DIP CABLE - HDM50S/AE50G/X |
| EEC17DRTH-S734 | CONN EDGECARD 34POS DIP .100 SLD |
| 1SMA5919BT3 | DIODE ZENER 5.6V 1.5W SMA |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MCZ33800EKR2 | 功能描述:马达/运动/点火控制器和驱动器 AUTO ENG CONTROL IC RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| MCZ33800R2 | 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:Engine Control Integrated Circuit |
| MCZ33810EK | 功能描述:马达/运动/点火控制器和驱动器 Ignition Injector Driver RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| MCZ33810EK/R2 | 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:Automotive Engine Control IC |
| MCZ33810EKR2 | 功能描述:马达/运动/点火控制器和驱动器 Ignition Injector Driver RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。