- 您现在的位置：买卖IC网 > PDF目录16608 > MCZ33800EK (Freescale Semiconductor)IC ENGINE CTRL SW/DVR 54-SOIC PDF资料下载
参数资料
| 型号： | MCZ33800EK |
| 厂商： | Freescale Semiconductor |
| 文件页数： | 29/39页 |
| 文件大小： | 0K |
| 描述： | IC ENGINE CTRL SW/DVR 54-SOIC |
| 标准包装： | 26 |
| 应用： | 自动 |
| 电流 - 电源： | 10mA |
| 电源电压： | 5 V ~ 36 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 54-BSSOP（0.295"，7.50mm 宽）裸露焊盘 |
| 供应商设备封装： | 54-SOICW-EP |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页当前第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页
FUNCTIONAL DEVICE OPERATION
LOGIC COMMANDS AND REGISTERS
greater than 0.0mA. Commands outside of this command
range will automatically lock out dither.
Programming the solenoid current begins by sending the
CCD2 Control command. The command consists of an
control address, Diagnostic Pull-up Enable bit (Diag_pu_EN),
Dither Disable bit (DTHR_DIS), and a 9-bits of data for digital
to analog conversion (DAC). The data is received and the
DAC provides bias for a comparator to produce a threshold
level. The comparator drives a switch control circuit which
generates a frequency modulated signal for the output drive.
The differential voltage across the sense resistor provides
the feedback necessary to maintain the desired output
current. The output current is continuously monitored as a
differential voltage across the internal sense resistor. When
the current is recirculation and the driver is in the off state, the
current will decay to the lower limit switch point. When the
current reaches the lower limit, the driver will turn on to
increase the current until the upper limit switch point is
reached. The output current will continue to switch between
the switch points, resulting in the desired average current.
The switch points are set to a fixed +/-5% of the commanded
Table 18. CCD2 Constant Current Controller Commands
current. The switching frequency and accuracy are
dependent upon the load inductance and resistance, battery
voltage, dither amplitude and frequency, switch points, and
the commanded current.
Current dither is a method by which the average current is
increased and decreased through the solenoid valve. The
33800 allows the user to program the frequency and
amplitude of the dither control. Dither amplitude is
implemented by increasing and decreasing the DAC by the
programmed dither value. The rate at which the value is
changed is set by the programmed dither frequency. When
reprogramming the dither amplitude or dither frequency, the
update will occur on the start of a positive cycle.
The maximum value of the output (DAC + Dither) must be
less than 232mA. When a greater value is programmed, the
device will disable dither on the output. Similarly, the
minimum value of the output (DAC - Dither) must be greater
than 0.0mA. Requesting a lower value will disable dither on
the output.
Command
Control Address
Command Bits
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
CCD2 Command Address
Diag DTHR
Pull-
DIS
up
9 BIT DAC Command Data
CCD2 Control
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0 = Pull-down Current Source
1 = Pull-up Current Source
CCD2 Command Address
CCD2
Dither Amplitude
Dither Frequency
Retry
CCD2 Frequency & Amplitude
1
1
0
0
1
1
X
X
X
0
1
1
0
1
0
0
Next SO Response (Message 2) OvrVlt Reset Trim VCAL Open Short Open Short Fault Fault Fault Fault Fault Fault Fault Fault
0 = No Fault, 1 = Fault
,TLim
Set (23) Status Fault Fault Fault Fault Status Status Status Status Status Status Status Status
or
CAL
int=0
ext=1
CCD2 CCD2 CCD1 CCD1 OUT8 OUT7 OUT6 OUT5 OUT4 OUT3 OUT2 OUT1
Flt
Notes
23. Trim Set bit indicates (0 = untrimmed, 1 = trimmed)
24. VCAL Status bit indicates when internal or external supply is used. VCAL Bit = 0 indicates external, VCAL Bit = 1indicates internal.
25. Reset Bit indicates the device has performed a POR.
33800
Analog Integrated Circuit Device Data
Freescale Semiconductor
29
相关PDF资料 |
PDF描述 |
|---|---|
| HSC05DRYI-S13 | CONN EDGECARD 10POS .100 EXTEND |
| ECC22DRYI | CONN EDGECARD 44POS DIP .100 SLD |
| H2MXS-5036G | DIP CABLE - HDM50S/AE50G/X |
| EEC17DRTH-S734 | CONN EDGECARD 34POS DIP .100 SLD |
| 1SMA5919BT3 | DIODE ZENER 5.6V 1.5W SMA |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MCZ33800EKR2 | 功能描述:马达/运动/点火控制器和驱动器 AUTO ENG CONTROL IC RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| MCZ33800R2 | 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:Engine Control Integrated Circuit |
| MCZ33810EK | 功能描述:马达/运动/点火控制器和驱动器 Ignition Injector Driver RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| MCZ33810EK/R2 | 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:Automotive Engine Control IC |
| MCZ33810EKR2 | 功能描述:马达/运动/点火控制器和驱动器 Ignition Injector Driver RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。