- 您现在的位置：买卖IC网 > PDF目录16608 > MCZ33800EK (Freescale Semiconductor)IC ENGINE CTRL SW/DVR 54-SOIC PDF资料下载
参数资料
| 型号： | MCZ33800EK |
| 厂商： | Freescale Semiconductor |
| 文件页数： | 26/39页 |
| 文件大小： | 0K |
| 描述： | IC ENGINE CTRL SW/DVR 54-SOIC |
| 标准包装： | 26 |
| 应用： | 自动 |
| 电流 - 电源： | 10mA |
| 电源电压： | 5 V ~ 36 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 54-BSSOP（0.295"，7.50mm 宽）裸露焊盘 |
| 供应商设备封装： | 54-SOICW-EP |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页当前第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页
FUNCTIONAL DEVICE OPERATION
LOGIC COMMANDS AND REGISTERS
temperature of the output driver to determine the fault. Both
methods may be selected or used individually. The following
table provides an explanation of operation during fault
condition.
The low duty cycle used for the timer protection scheme is
set by the fault timer used to detect the short circuit. For short
circuits detected based on the output voltage exceeding the
fault detection voltage threshold, the outputs will be turned off
for the duration of the refresh timer (typically 10ms) and
turned on for the duration of the on-state short circuit fault
timer (typically 500 μ s). For short circuits detected based on
the output current exceeding the output current limit, the
outputs will be turned off for the duration of the refresh timer
(typically 10 ms) and turned on for the duration of the current
limit fault timer (typically 50 μ s).
For off-state open load faults with retry timer enabled, the
off-open fault is released and re-detected every 1-2 retry
timer periods. Retry timer for 1-2, 3-4, 5-6, and 7-8 are out of
phase and may report a load present, if the OSS read
command CS is issued after the release, and before the re-
detection (~500 μ s) of the off-state open load fault.
Table 13. TLim/Timer Control
PARALLEL OUTPUT, PX PIN ENABLE COMMAND
The Parallel Output command allows the user to parallel
output for increased current capability and enables control of
the PX input pin.
A logic 0 in the Parallel Output Command provides
individual control. Logic 1 commands outputs to operate in
parallel. For example, with bit 4 in the Parallel Output
command a logic 1, outputs 1 & 2 are controlled together
With the outputs paralleled, and the P1 pin enabled, a logic
1 on SPI bit 0 or SPI bit 1 will command both outputs on.
Similarly a logic 1 on the P1 pin will command both outputs
on.
PX pin Enable bit 0 through bit 3 enables or disables the
P1, P3, P5, P7 pins respectively. A logic 0 in the SPI word will
enable the PX input pin, while logic 1 in the SPI word will
disable the PX input pin. Default state is with the PX input
pins enabled.
When paralleling output 1 & 2 the current limit is
maintained at 4.0 to 6.0A. Parallel current limit for drivers
3&4, 5&6, 7&8 is increased to a range of 2.0 to 4.0A.
Using a MOSFET as output switches allows the
connection of paired outputs. The R DS(ON) of MOSFET
Shutdn
Retry Bit
1
TLIM
Bit
0
Fault
Timer
Bit
X
Operation During Short Fault
Timer only, Outputs will retry on
devices have inherent positive temperature coefficient
providing balanced current sharing between outputs without
destructive operation. This mode of operation may be
desirable in the event the application requires lower power
period
OUT1-8 = ~500us for short
circuit faults, and 50us for current
limit faults ON, ~10ms OFF.
dissipation or the added capability of switching higher
currents. Performance of parallel operation results in a
corresponding decrease in R DS(ON) , while the Output Current
Limit increases correspondingly. Output OFF Open Load
1
1
1
1
0
1
TLim only, Outputs will retry on
TLim hysteresis.
Timer and TLim, Outputs will
Detect current may increase based on how the Output OFF
Open Load Detect is programmed.
Table 14. And/Or/SPI/Parallel Control
retry on period and driver
temperature below threshold.
OUT1-8 = ~500us ON, ~10ms
OFF
Parallel
En Bit
1
PX Pin
En Bit
0
PX Pin
X
AND/
OR Bit
X
SPI
Bit 1
0
SPI
Bit 0
0
Output
1&2
OFF
0
0
X
Timer only, Outputs will not retry
1
0
X
X
0
1
ON
on period
1
0
X
X
1
0
ON
OUT1-8 = ~500us ON, OFF
1
0
X
X
1
1
ON
0
1
0
TLim only, Outputs will not retry
on TLim hysteresis.
1
1
0
1(or)
0
0
OFF
0
1
1
Timer and TLim, Outputs will not
1
1
0
1(or)
0
1
ON
retry on period or TLim.
OUT1-8 = ~500us ON, OFF
All OSS outputs have a current limit control loop. Current
limit is always active in Normal Mode. Current limit for OUT1
and OUT2 is 4.0 to 6.0A. Current limit for OUT3 through
OUT8 is 1.0 to 2.0A.
1
1
1
1
1
1
1
1
1
1
1
1
1
1
0
0
0
X
1
1
1
1(or)
1(or)
0(and)
0(and)
0(and)
0(and)
0(and)
1
1
X
0
0
1
1
0
1
X
0
1
0
1
ON
ON
OFF
OFF
ON
ON
ON
33800
Analog Integrated Circuit Device Data
26
Freescale Semiconductor
相关PDF资料 |
PDF描述 |
|---|---|
| HSC05DRYI-S13 | CONN EDGECARD 10POS .100 EXTEND |
| ECC22DRYI | CONN EDGECARD 44POS DIP .100 SLD |
| H2MXS-5036G | DIP CABLE - HDM50S/AE50G/X |
| EEC17DRTH-S734 | CONN EDGECARD 34POS DIP .100 SLD |
| 1SMA5919BT3 | DIODE ZENER 5.6V 1.5W SMA |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MCZ33800EKR2 | 功能描述:马达/运动/点火控制器和驱动器 AUTO ENG CONTROL IC RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| MCZ33800R2 | 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:Engine Control Integrated Circuit |
| MCZ33810EK | 功能描述:马达/运动/点火控制器和驱动器 Ignition Injector Driver RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| MCZ33810EK/R2 | 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:Automotive Engine Control IC |
| MCZ33810EKR2 | 功能描述:马达/运动/点火控制器和驱动器 Ignition Injector Driver RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。