- 您现在的位置：买卖IC网 > PDF目录20357 > MCZ33937EK (Freescale Semiconductor)IC PRE-DRIVER 3PHASE 54-SOIC PDF资料下载
参数资料
| 型号： | MCZ33937EK |
| 厂商： | Freescale Semiconductor |
| 文件页数： | 27/48页 |
| 文件大小： | 0K |
| 描述： | IC PRE-DRIVER 3PHASE 54-SOIC |
| 标准包装： | 26 |
| 系列： | SMARTMOS™ |
| 配置： | 3 相桥 |
| 输入类型： | 非反相 |
| 延迟时间： | 265ns |
| 电流 - 峰： | 600mA |
| 配置数： | 1 |
| 输出数： | 3 |
| 高端电压 - 最大（自引导启动）： | 15V |
| 电源电压： | 8 V ~ 40 V |
| 工作温度： | -40°C ~ 135°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 54-BSSOP（0.295"，7.50mm 宽）裸露焊盘 |
| 供应商设备封装： | 54-SOICW-EP |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页当前第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页
FUNCTIONAL INTERNAL BLOCK DESCRIPTION
VSUP
V SUP
3x
T-Lim
VLS
3x
T-Lim
VLS
-
-
Desat.
Comp.
VSUP
+
1.4V
HS
Control
High Px_BOOT
-Side
Driver
Px_HS_G
Phase x
Output
Desat.
Comp.
VSUP
+
1. 4V
HS
Control
High Px_BOOT
-Side
Driver
Px_HS_G
Phase x Output
Shorted to VSUP
(High-Side
FET Shorted)
Phase
Comp.
VSUP
R
LS
Control
Low
-Side
Driver
Px_HS_S
Px_LS_G
Phase x Output
Shorted to Ground
(Low-Side
FET Shorted)
Phase
Comp.
VSUP
R
LS
Control
Low
-Side
Driver
Px_HS_S
Px_LS_G
Phase x
Output
R
VLS_CAP
Px_LS_S
To Current
Sense Amplif.
Phase
Return
RSense
R
VLS_CAP
Px_LS_S
To Current
Sense Amplif.
Phase
Return
RSense
Px_HS_G
tBLANK
Px_HS_G
Px_LS_G
Deadtime
tFILT
Px_LS_G
Deadtime
tBLANK
V SUP
Correct Phase x Output Voltage
VSUP
Phase x Output Voltage Shorted to VSUP
-V D
0.5V SUP
Correct
Phase x Output
Voltage Shorted to Ground
-VD
0.5VSUP
Correct Phase x Output Voltage
PHASEx
Fault
PHASEx
Fault
Correct
Phase Error
Desaturation Error
Figure 15. Short to Ground Detection
When switching from Low Side to High Side, the High Side
will be commanded ON after the end of the deadtime. The
deadtime period starts when the Low Side is commanded
OFF. If the voltage at Px_HS_S is less than 1.4V below V SUP
after the blanking time (t BLANK ) a desaturation fault is
initiated. An additional 1.0 ? s digital filter is applied from the
initiation of the desaturation fault before it is registered, and
all phase drivers are turned OFF (Px_HS_G clamped to
Px_HS_S and Px_LS_G clamped to Px_LS_S). If the
desaturation fault condition clears before the filter time
expires, the fault is ignored and the filter timer resets.
Valid faults are registered in the fault status register, which
can be retrieved by way of the SPI. Additional SPI commands
will mask the INT flag and disable output stage shutdown,
due to desaturation and phase errors. See the Logic
Commands and Registers section for details on masking INT
behavior and disabling the protective function.
Phase Error
Figure 16. Short to Supply Detection
Phase Comparator
Faults could also be detected as Phase Errors . A phase
error is generated if the output signal (at Px_HS_S) does not
properly reflect the drive conditions.
A phase error is detected by a Phase Comparator. The
Phase Comparator compares the voltage at the Px_HS_S
node with a reference of one half the voltage at the VSUP pin.
A High Side phase error (which will also trigger the
Desaturation Detector) occurs when the High Side FET is
commanded on, and Px_HS_S is still low at the end of the
deadtime and blanking time duration. Similarly, a LS phase
error occurs when the Low Side FET is commanded on, and
the Px_HS_S is still high at the end of the deadtime and
blanking time duration.
The Phase Error Flag is the triple OR of phase errors from
each phase. Each phase error is the OR of the High Side and
Low Side phase errors. This flag can generate an interrupt if
the appropriate mask bit is set. The INT will be held in the
High state until the fault is removed, and the appropriate bit
in the Status Register 0 is cleared by the CLINT1 command.
This fault reporting mechanism is described in detail in the
Logic Commands and Registers section.
33937A
Analog Integrated Circuit Device Data
Freescale Semiconductor
27
相关PDF资料 |
PDF描述 |
|---|---|
| 345-100-527-204 | CARDEDGE 100POS DUAL .100 GREEN |
| T95D107K016LSAS | CAP TANT 100UF 16V 10% 2917 |
| HCC05DRTS-S13 | CONN EDGECARD 10POS .100 EXTEND |
| VI-264-CX-S | CONVERTER MOD DC/DC 48V 75W |
| 345-100-527-202 | CARDEDGE 100POS DUAL .100 GREEN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MCZ33937EK/R2 | 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:Three Phase Field Effect Transistor Pre-driver |
| MCZ33937EKR2 | 功能描述:功率驱动器IC THREE PHASE PRE DRIVER RoHS:否 制造商:Micrel 产品:MOSFET Gate Drivers 类型:Low Cost High or Low Side MOSFET Driver 上升时间: 下降时间: 电源电压-最大:30 V 电源电压-最小:2.75 V 电源电流: 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube |
| MCZ33970EG | 功能描述:马达/运动/点火控制器和驱动器 DUAL GAGE DRVR IMP DAMP RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| MCZ33970EG | 制造商:Freescale Semiconductor 功能描述:IC STEPPER MOTOR GAUGE DRIVER SPI |
| MCZ33970EGR2 | 功能描述:马达/运动/点火控制器和驱动器 DUAL GAGE DRVR IMP DAMP RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。