- 您现在的位置：买卖IC网 > PDF目录45334 > MM908E626AVEK (FREESCALE SEMICONDUCTOR INC) FLASH, 32 MHz, MICROCONTROLLER, PDSO54 PDF资料下载
参数资料
| 型号： | MM908E626AVEK |
| 厂商： | FREESCALE SEMICONDUCTOR INC |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | FLASH, 32 MHz, MICROCONTROLLER, PDSO54 |
| 封装： | 5.10 X 10.30 MM, 0.65 MM PITCH, LEAD FREE, SOIC-54 |
| 文件页数： | 8/43页 |
| 文件大小： | 842K |
| 代理商： | MM908E626AVEK |
第1页第2页第3页第4页第5页第6页第7页当前第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页
Analog Integrated Circuit Device Data
16
Freescale Semiconductor
908E626
FUNCTIONAL DESCRIPTION
FUNCTIONAL PIN DESCRIPTION
CURRENT LIMITATION FREQUENCY INPUT PIN
(FGEN)
Input pin for the half-bridge current limitation PWM
frequency. This input is not a real PWM input pin; it should
just supply the period of the PWM. The duty cycle will be
generated automatically.
Important The recommended FGEN frequency should
be in the range of 0.1 kHz to 20 kHz.
BACK ELECTROMAGNETIC FORCE OUTPUT PIN
(BEMF)
This pin gives the user information about back
electromagnetic force (BEMF). This feature allows stall
detection and coil failures in step motor applications. In order
to evaluate this signal the pin must be directly connected to
pin PTD0/TACH0/BEMF.
RESET PIN (RST_A)
RST_A
is the bidirectional reset pin of the analog die. It is
an open drain with pull-up resistor and must be connected to
the RST pin of the MCU.
INTERRUPT PIN (IRQ_A)
IRQ_A
is the interrupt output pin of the analog die
indicating errors or wake-up events. It is an open drain with
pull-up resistor and must be connected to the IRQ pin of the
MCU.
SLAVE SELECT PIN (SS)
This pin is the SPI Slave Select pin for the analog chip. All
other SPI connections are done internally. SS must be
connected to PTB1 or any other logic I/O of the
microcontroller.
LIN BUS PIN (LIN)
The LIN pin represents the single-wire bus transmitter and
receiver. It is suited for automotive bus systems and is based
on the LIN bus specification.
HALF-BRIDGE OUTPUT PINS (HB1:HB4)
The 908E626 device includes power MOSFETs
configured as four half-bridge driver outputs. The HB1:HB4
outputs may be configured for step motor drivers, DC motor
drivers, or as high side and low side switches.
The HB1:HB4 outputs are short-circuit and over-
temperature protected, and they feature current recopy,
current limitation, and BEMF generation. Current limitation
and recopy are done on the low side MOSFETs.
POWER SUPPLY PINS (VSUP1:VSUP3)
VSUP1:VSUP3 are device power supply pins. The
nominal input voltage is designed for operation from 12 V
systems. Owing to the low ON-resistance and current
requirements of the half-bridge driver outputs, multiple VSUP
pins are provided.
All VSUP pins must be connected to get full chip
functionality.
POWER GROUND PINS (GND1 AND GND2)
GND1 and GND2 are device power ground connections.
Owing to the low ON-resistance and current requirements of
the half-bridge driver outputs multiple pins are provided.
GND1 and GND2 pins must be connected to get full chip
functionality.
SWITCHABLE VDD OUTPUT PIN (HVDD)
The HVDD pin is a switchable VDD output for driving
resistive loads requiring a regulated 5.0 V supply; The output
is short-circuit protected.
+5.0 V VOLTAGE REGULATOR OUTPUT PIN (VDD)
The VDD pin is needed to place an external capacitor to
stabilize the regulated output voltage. The VDD pin is
intended to supply the embedded microcontroller.
Important The VDD pin should not be used to supply
other loads; use the HVDD pin for this purpose. The VDD,
EVDD, VDDA, and VREFH pins must be connected together.
VOLTAGE REGULATOR GROUND PIN (VSS)
The VSS pin is the ground pin for the connection of all non-
power ground connections (microcontroller and sensors).
Important VSS, EVSS, VSSA, and VREFL pins must be
connected together.
LIN TRANSCEIVER OUTPUT PIN (RXD)
This pin is the output of LIN transceiver. The pin must be
connected to the microcontroller’s Enhanced Serial
Communications Interface (ESCI) module (RXD pin).
ADC REFERENCE PINS (VREFL AND VREFH)
VREFL and VREFH are the reference voltage pins for the
ADC. It is recommended that a high quality ceramic
decoupling capacitor be placed between these pins.
Important VREFH is the high reference supply for the
ADC and should be tied to the same potential as VDDA via
separate traces. VREFL is the low reference supply for the
ADC and should be tied to the same potential as VSS via
separate traces.
For details refer to the 68HC908EY16 datasheet.
ADC SUPPLY PINS (VDDA AND VSSA)
VDDA and VSSA are the power supply pins for the analog-
to-digital converter (ADC). It is recommended that a high
quality ceramic decoupling capacitor be placed between
these pins.
Important VDDA is the supply for the ADC and should be
tied to the same potential as EVDD via separate traces.
相关PDF资料 |
PDF描述 |
|---|---|
| MMAD1108R2 | 0.4 A, 8 ELEMENT, SILICON, SIGNAL DIODE |
| MMBD1504A-TP | 0.2 A, 2 ELEMENT, SILICON, SIGNAL DIODE |
| MMBD1505A-TP | 0.2 A, 2 ELEMENT, SILICON, SIGNAL DIODE |
| MMBD2837LT3 | 0.15 A, 2 ELEMENT, SILICON, SIGNAL DIODE, TO-236AB |
| MMBZ27VCL/DG | TVS DIODE, TO-236AB |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MM908E626AVPEK | 功能描述:8位微控制器 -MCU MCU + LIN + MOTOR DRIVER RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| MM908E626AVPEKR2 | 功能描述:8位微控制器 -MCU RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| MM908E626R2 | 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:Integrated Stepper Motor Driver with Embedded MCU and LIN Serial Communication |
| MM-90N | 功能描述:ANT MAGN MNT VEHIC 3.5"DIA 10'NF RoHS:是 类别:RF/IF 和 RFID >> RF 天线 系列:* 标准包装:1 系列:* |
| MM90R9F | 制造商:Ohmite Mfg Co 功能描述: |
发布紧急采购，3分钟左右您将得到回复。