参数资料
型号: MPC5200BV400
厂商: Freescale Semiconductor
文件页数: 26/72页
文件大小: 0K
描述: IC MPU 32BIT 400MHZ 272-PBGA
标准包装: 40
系列: MPC52xx
核心处理器: 603e G2 LE
芯体尺寸: 32-位
速度: 400MHz
连通性: CAN,EBI/EMI,以太网,I²C,IrDA,J1850,SPI,UART/USART,USB
外围设备: AC'97,DMA,I²S,POR,PWM,WDT
输入/输出数: 56
程序存储器类型: 外部程序存储器
RAM 容量: 16K x 8
电压 - 电源 (Vcc/Vdd): 1.42 V ~ 1.58 V
振荡器型: 内部
工作温度: 0°C ~ 70°C
封装/外壳: 272-BBGA
包装: 托盘
MPC5200B Data Sheet, Rev. 4
32
Freescale Semiconductor
NOTES:
1 tUI, tMLI, tLI indicate sender-to-recipient or recipient-to-sender interlocks. That is, one agent (sender or recipient) is waiting for
the other agent to respond with a signal before proceeding.
tUI is an unlimited interlock that has no maximum time value.
tMLI is a limited time-out that has a defined minimum.
tLI is a limited time-out that has a defined maximum.
2 All timing parameters are measured at the connector of the drive to which the parameter applies. For example, the sender shall
stop generating STROBE edges tRFS after negation of DMARDY. STROBE and DMARDY timing measurements are taken at
the connector of the sender. Even though the sender stops generating STROBE edges, the receiver may receive additional
STROBE edges due to propagation delays. All timing measurement switching points (low to high and high to low) are taken at
1.5 V.
t AZ
10
10
10
Maximum time allowed for output drivers to release
from being asserted or negated
A8.36
tZAH
20
20
20
Minimum delay time required for output drivers to
assert or negate from released state
A8.37
t ZAD
0—0—0—
A8.38
t ENV
20
70
20
70
20
70
Envelope time—from DMACK to STOP and
HDMARDY during data out burst initiation.
A8.39
t SR
50
30
20
STROBE to DMARDY time, if DMARDY is negated
before this long after STROBE edge, the recipient
receives no more than one additional data word.
A8.40
t RFS
75
60
50
Ready-to-Final STROBE time—no STROBE edges
are sent this long after negation of DMARDY.
A8.41
t RP
160
125
100
Ready-to-Pause time—the time recipient waits to
initiate pause after negating DMARDY.
A8.42
t IORDYZ
20
20
20
Pull-up time before allowing IORDY to be released.
A8.43
t ZIORDY
0
0
0
Minimum time drive waits before driving IORDY
A8.44
t ACK
20
20
20
Setup and hold times for DMACK, before assertion or
negation.
A8.45
t SS
50
50
50
Time from STROBE edge to negation of DMARQ or
assertion of STOP, when sender terminates a burst.
A8.46
Table 29. Ultra DMA Timing Specification (continued)
Sym
MODE 0
(ns)
MODE 1
(ns)
MODE 2
(ns)
Comment
SpecID
Min
Max
Min
Max
Min
Max
相关PDF资料
PDF描述
MCF5282CVF80 IC MPU 32BIT 66MHZ 256-MAPBGA
MPC563MZP56R2 IC MPU 512K FLASH 56MHZ 388-PBGA
VE-23W-IX-F4 CONVERTER MOD DC/DC 5.5V 75W
VI-24J-CV-S CONVERTER MOD DC/DC 36V 150W
VE-23W-IX-F3 CONVERTER MOD DC/DC 5.5V 75W
相关代理商/技术参数
参数描述
MPC5200CBV266 功能描述:微处理器 - MPU 266MHz 760MIPS RoHS:否 制造商:Atmel 处理器系列:SAMA5D31 核心:ARM Cortex A5 数据总线宽度:32 bit 最大时钟频率:536 MHz 程序存储器大小:32 KB 数据 RAM 大小:128 KB 接口类型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作电源电压:1.8 V to 3.3 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:FBGA-324
MPC5200CBV400 功能描述:微处理器 - MPU 400MHz 760MIPS RoHS:否 制造商:Atmel 处理器系列:SAMA5D31 核心:ARM Cortex A5 数据总线宽度:32 bit 最大时钟频率:536 MHz 程序存储器大小:32 KB 数据 RAM 大小:128 KB 接口类型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作电源电压:1.8 V to 3.3 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:FBGA-324
MPC5200CBV400B 制造商:Freescale Semiconductor 功能描述:
MPC5200CVR266 功能描述:微处理器 - MPU NO-PB IND’L 5200 266MHZ RoHS:否 制造商:Atmel 处理器系列:SAMA5D31 核心:ARM Cortex A5 数据总线宽度:32 bit 最大时钟频率:536 MHz 程序存储器大小:32 KB 数据 RAM 大小:128 KB 接口类型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作电源电压:1.8 V to 3.3 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:FBGA-324
MPC5200CVR400 功能描述:微处理器 - MPU NO-PB IND’L 5200 400MHZ RoHS:否 制造商:Atmel 处理器系列:SAMA5D31 核心:ARM Cortex A5 数据总线宽度:32 bit 最大时钟频率:536 MHz 程序存储器大小:32 KB 数据 RAM 大小:128 KB 接口类型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作电源电压:1.8 V to 3.3 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:FBGA-324