参数资料
型号: MPC8245TVV266D
厂商: MOTOROLA INC
元件分类: 微控制器/微处理器
英文描述: 32-BIT, 266 MHz, RISC PROCESSOR, PBGA352
封装: 35 X 35 MM, 1.70 MM HEIGHT, 1.27 MM PITCH, CAVITY-UP, TBGA-352
文件页数: 47/60页
文件大小: 674K
代理商: MPC8245TVV266D
MOTOROLA
MPC8245 Integrated Processor Hardware Specications
51
System Design Information
Wakeeld Engineering
603-635-5102
33 Bridge St.
Pelham, NH 03076
Internet: www.wakeeld.com
Ultimately, the nal selection of an appropriate heat sink depends on many factors, such as thermal
performance at a given air velocity, spatial volume, mass, attachment method, assembly, and cost. Other heat
sinks offered by Aavid Thermalloy, Alpha Novatech, IERC, Chip Coolers, and Wakeeld Engineering offer
different heat sink-to-ambient thermal resistances, and may or may not need airow.
1.7.9.1
Internal Package Conduction Resistance
For the TBGA, cavity down, packaging technology, shown in Figure 29, the intrinsic conduction thermal
resistance paths are as follows:
The die junction-to-case thermal resistance
The die junction-to-ball thermal resistance
Figure 29 depicts the primary heat transfer path for a package with an attached heat sink mounted to a
printed-circuit board.
Figure 29. TBGA Package with Heat Sink Mounted to a Printed-Circuit Board
In TBGA package the active side of the die faces the printed-circuit board. Most of the heat travels through
the die, across the die attach layer, into the copper spreader. Some of the heat is removed from the top
surface of the spreader through convection and radiation.
Another portion of the heat enters the
printed-circuit board through the solder balls. The heat is then removed off the exposed surfaces of the
board through convection and radiation. If a heat sink is used a larger percentage of heat leaves through the
top side of the spreader.
1.7.9.2
Adhesives and Thermal Interface Materials
A thermal interface material is recommended between the top of the package and the bottom of the heat sink
to minimize the thermal contact resistance. For those applications where the heat sink is attached by spring
clip mechanism, Figure 30 shows the thermal performance of three thin-sheet thermal-interface materials
External Resistance
Internal Resistance
Radiation
Convection
Radiation
Convection
Heat Sink
Printed-Circuit Board
Thermal Interface Material
Package/Leads
Die Junction
Die/Package
(Note the internal versus external package resistance)
相关PDF资料
PDF描述
MPC8245TVV333D 32-BIT, 333 MHz, RISC PROCESSOR, PBGA352
MC9S08SG16VTJR 8-BIT, FLASH, 40 MHz, MICROCONTROLLER, PDSO20
MC9S08SG16WTLR 8-BIT, FLASH, 40 MHz, MICROCONTROLLER, PDSO28
M30812MC-XXXGP 32-BIT, MROM, 32 MHz, MICROCONTROLLER, PQFP144
MC68HC705C9AFN 8-BIT, OTPROM, 2.1 MHz, MICROCONTROLLER, PQCC44
相关代理商/技术参数
参数描述
MPC8245TVV300D 功能描述:微处理器 - MPU INTEGRATED HOST PROC RoHS:否 制造商:Atmel 处理器系列:SAMA5D31 核心:ARM Cortex A5 数据总线宽度:32 bit 最大时钟频率:536 MHz 程序存储器大小:32 KB 数据 RAM 大小:128 KB 接口类型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作电源电压:1.8 V to 3.3 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:FBGA-324
MPC8245TVV333D 功能描述:微处理器 - MPU INTEGRATED HOST PROC RoHS:否 制造商:Atmel 处理器系列:SAMA5D31 核心:ARM Cortex A5 数据总线宽度:32 bit 最大时钟频率:536 MHz 程序存储器大小:32 KB 数据 RAM 大小:128 KB 接口类型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作电源电压:1.8 V to 3.3 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:FBGA-324
MPC8245TVV350D 功能描述:微处理器 - MPU INTEGRATED HOST PROC RoHS:否 制造商:Atmel 处理器系列:SAMA5D31 核心:ARM Cortex A5 数据总线宽度:32 bit 最大时钟频率:536 MHz 程序存储器大小:32 KB 数据 RAM 大小:128 KB 接口类型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作电源电压:1.8 V to 3.3 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:FBGA-324
MPC8245TZU266D 功能描述:微处理器 - MPU 266MHz 505.4MIPS RoHS:否 制造商:Atmel 处理器系列:SAMA5D31 核心:ARM Cortex A5 数据总线宽度:32 bit 最大时钟频率:536 MHz 程序存储器大小:32 KB 数据 RAM 大小:128 KB 接口类型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作电源电压:1.8 V to 3.3 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:FBGA-324
MPC8245TZU300D 功能描述:微处理器 - MPU 300MHz 570MIPS RoHS:否 制造商:Atmel 处理器系列:SAMA5D31 核心:ARM Cortex A5 数据总线宽度:32 bit 最大时钟频率:536 MHz 程序存储器大小:32 KB 数据 RAM 大小:128 KB 接口类型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作电源电压:1.8 V to 3.3 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:FBGA-324